Applications; Preparation Before Operation - Hitachi Koki C10FCH2 Instruction Manual

I English
OPTIONAL ACCESSORIES...sold separately
[1] Extension Holderand Stopper (Code No.322710)
42) Saw blade 10" (255mm)TCT Saw blade for wood cut (Totalteeth:
60) (CodeNo.976472)
[3) Sawblade10"(255mm)TCTSawbladefor aluminum cut (Totalteeth:
100) (CodeNo.319658)
[4_ Crown molding Vise Ass'y (Code No. 322712) (Include Crown
molding Stopper (L))
[5) Crown molding Stopper (L) (CodeNo. 322713)
[6) Crown molding Stopper (R) (CodeNo. 322714)
NOTE:
Accessories a re subjectto changewithout any obligationon the
part of the HITACHI.
APPLICATIONS
Wood and aluminum sash.
PREPARATION BEFORE OPERATION
Make the following preparations before operating the power tool:
1. Installation
16-3/8" (416mm)
11/32" (9mm)
4 Holes
_ 14-1/6" (360mm)
.)
)1
Base -=
{3
5/16" (8ram) Bol
E
Work bench 5/16" (8ram) Nut
Fig.4
Attach the power tool to a level, horizontal work bench in accordance
with Fig. 4.
Select 5/16" (8mm) diameter bolts suitable in length for the thickness
of the work bench.
Bolt length should be at least 1-3/8" (35mm) plus the thickness of
the work bench.
For example, use 2-11/32" (60ram) or larger bolts for a 1" (25ram)
thick work bench.
The holder attached to the rear of the base helps stabilize the power
tool.
Holder (B),clamp lever adjustment:
Attach the included holder (B) in the position as shown in figure 5
and adjustthe holder (B) until its bottom surfacecontactsthe work
benchsurface. A fter adjustments,securelytighten the 6mm bolt with
the included 10mmbox wrench. Loosenthe M6 x 20 screw on the
clamp lever and attach to a position where the clamp lever can be
easilyoperated.
/_ CAUTION:
Attachthe powertoolto a workbenchwith bolts(6mm),andif the
turntablehasbeenswiveled45° degrees or more,becarefulnotto
letthe handthat isholding the sidehandlegetcaughtbetweenthe
sidehandleandheadsof bolts(6mm). InJuries c ouldresult.
M6x2OScrew _ ___
Adjust tiilii[__
until its bottom Move
surface contacts the
work bench surface.
Fig.5-a
Install the side handle
Remove the MIO bolt and install the side handle that came enclosed
with this unit.
MIO Bolt
Fig.5-b
Install the sub fence(B)
In the case of direct angle cutting and angle cutting, use the sub
fence. The sub fence (B) can be installed on the right side of the
guide fence(B).Placethe attachedplate (A)in the position asshown
in figure 11, insert the tip in the groove of fence (B) and
simultaneously, insert flathead screw M6 into fence (B), sub fence
(B),and plate(A),thentighten nylon nut M6 with the included 10mm
box wrench until the sub fence (B) can smoothly rotate. Then, you
can realizestablecutting of the materialwith a wide backface.
_\M6 Flat screw
Sub fence (_ Plate (A_J_'\'\ ,.-_
M6 Nylon nut_,j_
Fence (B)
Fig.5-c
Releasingthe locking pin
When the power tool is prepared for shipping, its main parts are
securedby a locking pin.
Move the handleslightly so that the locking pin can be disengaged.
NOTE:
Loweringthe handle slightly willenableyou todisengage the locking
pin moreeasilyandsafely.
Thelockpositionofthe locking pin isfor carryingandstorageonly.