Wolf ICBDF304 Installation Instructions Manual page 10

W O L F D UA L F U E L R A N G E S
G A S R A T I N G
Total Heat Electrical
Ouput Gas Rating ppliance
Model # (Gas) Units ( mps) Category
I2H
ICBDF304 17.1 kW 20
I2E
I2E+
ICBDF304-LP 1051 g/h 20 I3P
I2H
ICBDF364C 22.7 kW 20
I2E
I2E+
ICBDF364C-LP 1425 g/h 20 I3P
I2H
ICBDF364G 22.7 kW 20
I2E
I2E+
ICBDF364G-LP 1425 g/h 20 I3P
I2H
ICBDF366 26.7 kW 20
I2E
I2E+
ICBDF366-LP 1632 g/h 20 I3P
I2H
ICBDF484CG 28.3 kW 30
I2E
I2E+
ICBDF484CG-LP 1800 g/h 30 I3P
I2H
ICBDF486C 32.3 kW 30
I2E
I2E+
ICBDF486C-LP 2007 g/h 30 I3P
I2H
ICBDF486G 32.3 kW 30
I2E
I2E+
ICBDF486G-LP 2007 g/h 30 I3P
I2H
ICBDF484DG 28.3 kW 30
I2E
I2E+
ICBDF484DG-LP 1800 g/h 30 I3P
I2H
ICBDF484F 21.9 kW 30
I2E
I2E+
ICBDF484F-LP 1342 g/h 30 I3P
I2H
ICBDF604CF 27.5 kW 40
I2E
I2E+
ICBDF604CF-LP 1716 g/h 40 I3P
I2H
ICBDF606CG 37.9 kW 40
I2E
I2E+
ICBDF606CG-LP 2381 g/h 40 I3P
10
Types and
Pressures
(mbar) Country of Designation
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
T, DK, EE, FI, GR, IE, IT, LT, NO, PT, ES,
G20 at 20
SE, SI, SK, GB, CH
G20 at 20 DE, PL
G20 at 20/25 BE, FR
G31 at 37 BE, CZ, FR, GR, IE, NL, NO, PT, ES, GB, CH
E L E C T R I C A L R E Q U I R E M E N T S
Verify that power is disconnected from
the electrical box before proceeding.
R E Q U I R E D P O W E R S U P P LY
Single phase: 220-240V C; 50/60 Hz
3phase: 380-415V C; 50/60 Hz
M A X I M U M C O N N E C T E D L O A D
762 mm and 914 mm Dual Fuel ranges:
Single phase: 20 amps
3phase: 20 amps
1219 mm Dual Fuel ranges:
Single phase: 30 amps
3phase: 20 amps
1524 mm Dual Fuel ranges:
Single phase: 40 amps
3phase: 20 amps
Refer to the wiring diagram showing the
connections for each lead to the terminal box
on the unit.
Single phase wiring diagram
3phase wiring diagram
The complete appliance must be properly
grounded at all times when electrical
power is applied.
NOTE: Improper connection can result in
a fire hazard.
Before obtaining access to terminals, all
supply circuits must be disconnected.
Open the terminal box to expose the screws
with corresponding numbers. Run the cord
through the strain relief hole and into the
terminal box.
For Single Phase Install (Line, Neutral,
Ground): Loosen the 1, 5, and ground screws.
ttach the Neutral wire to the number 5
position. Line should be attached to the 1
postion and attach the ground to the corre-
sponding ground screw.
For 3phase Install (L1, L2, L3, Neutral,
Ground): Loosen the 1, 2, 3 and remove the
copper bars. Loosen 5 and ground screws.
ttach L1 to position 1. L2 to position 2. L3 to
position 3. Neutral wire to position 5 and attach
the ground to the corresponding ground screw.
IMPORT NT NOTE: Connection of this appli-
ance should be through a fused connection
unit or a suitable isolator, which complies with
national and local safety regulations. The
on/off switch should be easily accessible after
the appliance has been installed. If the switch
is not accessible after installation (depending
on country) an additional means of disconnec-
tion must be provided for all poles of the
power supply. When switched off there must
be an all pole contact gap of 3 mm in the
isolator switch. This 3 mm contact disconnect
gap must apply to any isolator switch, fuses
and/or relays according to EN60335.
Copper bars must be removed from posi-
tions 1, 2, and 3 when connecting to
3phase power.