Metra Electronics 99-6510 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. Metra Electronics Manuals
  4. Automobile Accessories
  5. 99-6510
  6. Installation instructions manual

Metra Electronics 99-6510 Installation Instructions Manual

For chrysler 300 2005-2007, aspen 2007; dodge caliber 2007-2008, charger 2005-2007, durango 2005-2007, magnum 2005-2007, ram 1500 2006-2008, ram 2500/3500 2006-2008, jeep commander 2006-2007, compass 2007-2008, grand cherokee 2005-2007, patriot 2007-2008
Hide thumbs Also See for 99-6510:
Table of Contents

Advertisement

Quick Links

See also: User Manual
INSTALLATION INSTRUCTIONS FOR PART 99-6510
Dodge
Caliber
Charger
Durango
Magnum 2005-2007
Ram 1500 2006-2008
Ram 2500/3500 2006-2008
Designed For Vehicles With Factory Navigation Radios
Using this kit in vehicles without factory navigation requires the purchase of a factory
navigation radio trim panel from your local Chrysler, Dodge or Jeep parts department.
99-6510
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO DIN Radio Provision with Pocket
• Double DIN Radio Provision
• Stacked ISO Units Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Double DIN Brackets • E) Pocket • F) Double DIN Trim Plate
A
Phillips Screwdriver • Socket Wrench •
1-800-221-0932
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
APPLICATIONS
Chrysler
300
2005-2007
Aspen
2007
2007-2008
2005-2007
2005-2007
C
B
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• XSVI-6502-NAV - Chrysler CAN R.A.P. interface 2004-up
F
• CHTO-01 - Chrysler CAN amp interface 2004-up
Antenna Adapter:
• 40-CR10 - Chrysler antenna adapter 2004-up
TOOLS REQUIRED:
Small Flat Blade Screwdriver or
• Panel Removal Tool
www.metraonline.com
Jeep
Commander
2006-2007
Compass
2007-2008
Grand Cherokee 2005-2007
Patriot
2007-2008
D
• Cutting Tool
E

Advertisement

Table of Contents
loading

Related Manuals for Metra Electronics 99-6510

Summary of Contents for Metra Electronics 99-6510

  • Page 1 INSTALLATION INSTRUCTIONS FOR PART 99-6510 Dodge Caliber 2007-2008 Charger 2005-2007 Durango 2005-2007 Magnum 2005-2007 Ram 1500 2006-2008 Ram 2500/3500 2006-2008 Designed For Vehicles With Factory Navigation Radios Using this kit in vehicles without factory navigation requires the purchase of a factory navigation radio trim panel from your local Chrysler, Dodge or Jeep parts department.

  • Page 2: Table Of Contents

    99-6510 T ABLE OF CONTENTS Dash Disassembly - Chrysler Aspen 2007 ..........1 - Dodge Durango 2005-2007 .

  • Page 3: Dash Disassembly

    99-6510 CHRYSLER ASPEN 2007 DODGE DURANGO 2005-2007 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove (2) 7MM screws from the inside of the pocket facing upward. (Figure A) Unclip and remove the entire trim panel surrounding the radio and climate controls.

  • Page 4: Dodge Charger 2005-2007

    99-6510 DODGE CHARGER 2005-2007 DODGE MAGNUM 2005-2007 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove entire panel surrounding radio and climate controls, including a/c vents. (Figure A) Remove (4) 7MM screws securing radio to dash and remove radio. (Figure B) Continue to kit assembly.

  • Page 5: Chrysler 300 2005-2007

    99-6510 CHRYSLER 300 2005-2007 Disconnect the negative battery terminal to prevent an accidental short circuit. Unclip and remove entire panel surround- ing radio and climate controls, including a/c vents and clock. (Figure A) Remove (4) 7MM screws securing radio to dash and remove radio. (Figure B) Continue to kit assembly.

  • Page 6: Dodge Ram 2006-08 (Without Center Console)

    99-6510 DODGE RAM 1500 2006-2008 WITHOUT CENTER CONSOLE RAM 2500/3500 2006-2008 Disconnect the negative battery terminal to prevent an accidental short circuit. Open cup holder and remove (2) Phillips screws facing up on front edge of radio/climate control panel. (Figure A)

  • Page 7: Dodge Ram 2006-08 (With Mini Center Console)

    99-6510 DODGE RAM 1500 2006-2008 WITH MINI CENTER CONSOLE RAM 2500/3500 2006-2008 Disconnect the negative battery terminal to prevent an accidental short circuit. If vehicle has floor shifter, remove shifter knob. Remove center console inserts, if present. (Figure A) Remove screws securing the rear center console to the floor panel.

  • Page 8: Dodge Ram 2006-08 (With Full Center Console)

    99-6510 DODGE RAM 1500 2006-2008 WITH FULL CENTER CONSOLE RAM 2500/3500 2006-2008 Disconnect the negative battery terminal to prevent an accidental short circuit. If vehicle has floor shifter, remove shifter knob. Unsnap and remove console front top cover (closest to the dash). (Figure A) Remove two 8 mm screws from under console cover (previously removed).

  • Page 9: Jeep Grand Cherokee 2005-2007

    99-6510 JEEP GRAND CHEROKEE 2005-2007 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and remove panel from around radio including the vent on each side. (Figure A) Remove (4) 7MM screws securing radio to dash and remove radio. (Figure B) Continue to kit assembly.

  • Page 10: Jeep Compass 2007-2008

    99-6510 DODGE CALIBER 2007-2008 JEEP COMPASS 2007-2008 JEEP PATRIOT 2007-2008 Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap and move shifter trim to the side. (Figure A) (Compass and Patriot only) Unsnap and remove top center dash panel above AC vents.

  • Page 11: Jeep Commander 2007

    99-6510 JEEP COMMANDER 2006-2007 Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the (16) screws securing the radio trim panel. (Figure A) screws Unclip and remove the entire radio trim panel. (Figure B) Remove (4) 7MM screws securing radio to dash and remove radio.

  • Page 12: Kit Assembly

    99-6510 DIN RADIO PROVISION WITH POCKET Slide the DIN cage into the radio housing and secure by bending the metal locking tabs down. (Figure A) Slide the aftermarket radio into the cage until secure. (Figure B) Snap the pocket into the radio housing.

  • Page 13: Iso Radio Provision With Pocket

    99-6510 ISO RADIO PROVISION WITH POCKET Mount the ISO Brackets to the radio with the screws supplied with the unit. (Figure A) Slide the radio into the radio opening until the side clips engage. (Figure B) Snap the ISO Trim Plate into the radio housing.

  • Page 14: Double Din Radio Provision

    99-6510 DOUBLE DIN RADIO PROVISION Cut and remove center divider in radio housing. (Figure A) Snap the DDIN brackets to the inside edge of the radio housing. (Figure B) Slide the DDIN radio unit into the DDIN bracket/radio housing assembly and secure the radio unit to the kit using the screws sup- plied with the radio unit.

  • Page 15: Stacked Iso Units Provision

    99-6510 STACKED ISO UNITS PROVISION Cut and remove center divider in radio housing. (Figure A) Snap the DDIN brackets to the inside edge of the radio housing. (Figure B) Slide the stacked ISO DIN radio units into the DDIN bracket/radio...

  • Page 16: Final Assembly

    *NOTE: When Black a wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications. 1-800-221-0932 REV. 06/02/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION FINAL ASSEMBL Y Strip wire ends back 1/2" Twist ends together...

Table of Contents