Unipulse F701-C Weighing Controller Manuals

Unipulse F701-C Weighing Controller Manuals

Manuals and User Guides for Unipulse F701-C Weighing Controller. We have 2 Unipulse F701-C Weighing Controller manuals available for free PDF download: Operation Manual, Manual

Unipulse F701-C Operation Manual

Unipulse F701-C Operation Manual (189 pages)

Brand: Unipulse | Category: Accessories | Size: 2 MB

Table of Contents

Safety Precautions
2
Table of Contents
6
1 ．Appearance Description

12
- Front Panel
  12
  - Status Display
    14
  - Function Keys
    15
- Rear Panel
  17
2 ．Connection

19
- Load Cell Connection
  19
  - 6-Wire Connection
    21
  - Connecting Load Cells in Parallel
    22
  - Sensor Cable
    22
- Connection of the Power Input Terminals
  23
- Connection of the Guard Ground
  23
- SI/F Connection
  24
- Connection of the Control Connector
  25
3 ．Methods of Setting

28
- Setting Procedure
  28
  - Method of Selecting a Setting Mode
    28
  - Method of Entering a Setting Value
    30
- Setting Mode
  34
  - Setting Mode 0
    35
  - Setting Mode 1
    37
  - Setting Mode 2
    39
  - Setting Mode 3
    42
  - Setting Mode 4
    44
  - Setting Mode 5
    47
  - Setting Mode 8
    49
4 ．Calibration

52
- Span Calibration
  52
- Span Calibration Procedure
  53
- Secondary Calibration Procedure (Equivalent Calibration)
  54
- Preparation for Calibration
  56
  - LOCK Release
    56
  - Unit
    57
  - Decimal Place
    57
  - Capacity
    58
  - Minimum Scale Division
    58
  - Balance Weight Value
    59
  - Gravitational Acceleration
    59
  - 1/4 Scale Division
    61
- Zero Calibration
  62
- Span Calibration
  64
- Secondary Calibration (Equivalent Calibration)
  65
5 ． Function Settings

66
- Display Frequency
  66
- Subdisplay Selection
  67
- Digital Filter
  67
- Analog Filter
  68
- Filter in Stable Condition
  68
- Motion Detection (MD)
  69
- Zero Tracking (ZT)
  71
- Digital Zero (DZ)
  72
- Digital Zero Clear
  73
- Zero Regulation Value
  73
- One-Touch Tare Subtraction
  74
- One-Touch Tare Subtraction Reset
  75
- Digital Tare Subtraction
  76
- Restriction of the Tare Subtraction Function
  77
- Switching Gross Weight/Net Weight Display
  78
- Reversing Symbol at Discharging Control
  79
- Invalidation of Function Keys
  79
6 ．Discharging Control Mode

80
7 ． Statistical and Accumulation Function Setting and Operation

113
- Data Display
  114
- Accumulation Command
  114
- Accumulation Clear
  116
- Auto Accumulation Command
  118
8 ．System Mode

120
- LOCK (Soft)
  120
- Password
  120
- Self-Check and Memory Clear
  121
9 ．External Input/Output Signals

122
- (Control Connector)
  122
- Control Connector-Pin Assignment
  122
- Equivalent Circuit (Input)
  123
- Equivalent Circuit (Output)
  123
- External Input Signal
  124
  - Gross/Net Switching (G/N) <Edge Input> <Level Input
    124
  - Digital Zero (D/Z ON) <Edge Input
    124
  - Tare Subtraction (TARE ON) <Edge Input
    125
  - Tare Subtraction Reset (TARE OFF) <Edge Input
    125
  - Hold (HOLD) <Level Input
    125
  - Judge <Level Input
    126
  - Feed / Discharge <Level Input
    126
  - Input Signals Used in Sequence Mode
    126
  - Accumulation Command <Edge Input
    127
  - Accumulation Clear <Edge Input
    127
  - Input Selection
    128
- External Output Signal
  129
  - Near Zero
    129
  - Lower Limit, Upper Limit
    129
  - Stable
    129
  - Weight Error
    129
  - Sequence Error
    130
  - Run
    130
  - Accumulation Error
    130
  - Sp1, Sp2, Sp3
    131
  - Under, Go, over
    132
  - Complete
    133
  - Output Selection
    134
10 ．Interface

135
- 2-Wire Serial Interface (SI/F)
  135
  - Connection
    135
  - Auto Print Command
    135
- RS-232C Interface
  136
  - Communication Specifications
    136
  - Cable
    136
  - Setting Values for RS-232C
    137
  - Communication Mode
    137
  - Transmission Format
    139
  - Communication Format
    140
- BCD Parallel Data Output Interface
  148
  - Control Connector-Pin Assignment
    148
  - Equivalent Circuit (Input)
    148
  - Equivalent Circuit (Output)
    149
  - BCD Data Output
    149
  - Polarity Output (MINUS)
    149
  - Over Status Output (OVER)
    150
  - Print Command Output
    150
  - Data Strobe (STROBE)
    150
  - BCD Data Update Rate Selection
    151
  - Data Hold Input
    151
  - Logic Switching Input
    151
  - Output Selection Input
    151
- D/A Converter
  152
  - Name of each Part
    152
  - Specifications
    154
  - Method of Adjusting the D/A Zero and Gain
    154
  - About D/A Resolution
    156
- Communication Interface
  157
  - Communication Specifications
    157
  - Connection
    157
  - RS-485 Communication Interface
    157
  - Setting Values for RS-485
    158
  - Communication Method
    159
  - Communication Format
    160
11 ．Over Scale & Error

168
- Over Scale
  168
- Sequence Error
  168
- Calibration Error
  169
12 ．Trouble Shooting

170
- Error Display
  171
13 ．Replacement of the Backup Battery

177
14 ．Block Diagram

178
15 ．Dimensions

179
16 ．Mounting on a Panel

180
17 ．Specifications

181
- Analog Section
  181
- Display Section
  182
- Setting Section
  182
- External Input/Output
  183
- Interface
  183
- General Performance
  185
- Attachment
  186
18 ．The List of Initial Setting Value

187
- Setting Mode 0
  187
- Setting Mode 1
  187
- Setting Mode 2
  188
- Setting Mode 3
  188
- Setting Mode 4
  188
- Setting Mode 5
  189
- Setting Mode 8
  189
- Calibration Mode (Setting Mode 9)
  189

Advertisement

Unipulse F701-C Manual

Unipulse F701-C Manual (39 pages)

WEIGHING INDICATOR

Brand: Unipulse | Category: Accessories | Size: 2 MB

Advertisement

Related Products

Unipulse Categories

Measuring Instruments Touch Panel Controller

Monitor

Monitor Accessories

More Unipulse Manuals