Kikusui TOS9303LC Safety Analyzer Manuals

Manuals and User Guides for Kikusui TOS9303LC Safety Analyzer. We have 2 Kikusui TOS9303LC Safety Analyzer manuals available for free PDF download: User Manual

Kikusui TOS9303LC User Manual (340 pages)

Electrical Safety Analyzer

Brand: Kikusui | Category: Measuring Instruments | Size: 18 MB

About Manuals
3
Open Source Software
3
Accessories
4
Product Overview
4
Notations Used in this Manual
5
Safety Precautions
5
Notes on Usage
6
Table of Contents
7
Component Names
12
Safety Precautions for Testing

19
- Lighting of the DANGER LED
  19
- Test Precautions
  19
- Precautions after Output Has Been Turned Off21
  21
  - Estimated Discharge Time
    21
- Remote Control Precautions
  22
- Malfunction Precautions
  22
  - Dangerous Malfunctions
    22
  - Emergency Measures
    22
- Protection Functions
  23
Installation

25
Basic Operation

46
- Basic Panel Operations
  46
  - Switching Menus
    46
  - Using the Function Keys
    47
  - Inputting Numbers and Characters
    49
  - Changing Values
    50
- Selecting the Test Mode
  51
  - Selecting the Test Mode
    52
Withstanding Voltage and Insulation Resistance Tests

53
- Setting Test Conditions
  53
  - Displaying the Setup Screen (Home Menu)
    53
  - Description of Test Conditions
    54
  - Test Voltage
    55
  - Limit Voltage
    56
  - Start Voltage
    57
  - End Voltage
    58
  - Frequency
    59
  - Upper Limit
    60
  - Lower Limit
    61
  - Unit of Criteria (Judge Type)
    62
  - Auto Setting of the Judgment Delay (Delay Auto)
    63
  - Test Time
    65
  - Voltage Rise Time
    66
  - Voltage Fall Time
    67
  - Discharge Time
    68
  - Discharge When Interlock Is Activated (Discharge Interlock)
    69
  - Current Detection Response Speed (Filter)
    70
  - Grounding Mode (GND)
    71
  - Current Measurement Mode (Current RMS)
    73
  - Voltage Measurement Mode (Volt Measure)
    74
  - Using the Low-Pass Filter
    75
  - Peak Value Display (Display Peakhold)
    76
  - Offset (Offset Real, Offset Imag)
    77
  - Offset
    78
  - Checking the Scanner Contact (Contact Check)
    79
  - Setting Scanner Channels (Edit)
    80
  - Opening the Scanner (All Open)
    81
- Starting a Test
  82
  - Output Time Limit
    82
  - Starting a Test
    83
Patient Leakage Current

84
- Operation after a Test Starts
  84
Test

84
- Changing the Voltage Setting During a Test
  87
- Finishing the Test and Viewing the Judgment
  88
Earth Continuity Test

90
- Setting Test Conditions
  90
  - Displaying the Setup Screen (Home Menu)
    90
  - Description of Test Conditions
    91
  - Test Current
    91
  - Limit Current
    92
  - Frequency
    92
  - Upper Limit
    93
  - Lower Limit
    94
  - Test Time
    95
  - Current Rise Time
    96
  - Current Fall Time
    96
  - Terminal Wiring Method (Terminals Wire)
    97
  - Contact Check
    98
  - Peak Value Display (Display Peakhold)
    99
  - Offset
    100
- Starting a Test
  101
  - Output Time Limit
    101
  - Operation after a Test Starts
    102
  - Changing the Current Setting During a Test
    105
- Finishing the Test and Viewing the Judgment106
  106
  - Stopping Tests
    106
  - Conditions that Cause a Test to End
    106
  - Judgment Types and Operation
    107
  - Clearing the Judgment Result
    107
Partial Discharge Test

108
Touch Current Test

134
- Setting Test Conditions
  134
  - Displaying the Setup Screen (Home Menu)
    134
  - Description of Test Conditions
    135
  - Network
    136
  - Polarity of the Power Supply Line
    137
  - Single Fault Mode (Condition)
    138
  - Probe Connection Destination
    139
  - Output from the 110% Terminal (110% OUT)
    140
  - Upper Limit
    141
  - Lower Limit
    142
  - Judgment Delay (Judge Delay)
    143
  - Test Time
    144
  - Measurement Range
    145
  - Measurement Mode (Measure Mode)
    147
  - Peak Value Display (Display Peakhold)
    149
  - Measurement Check (Measure Check)
    149
  - Offset
    150
  - Voltage Conversion (Conv Voltage)
    151
  - Checking the EUT Operation (Line OUT)
    151
- Starting a Test
  152
  - Connecting the Test Leads to the EUT
    152
  - Starting a Test
    154
  - Operation after a Test Starts
    155
- Finishing the Test and Viewing the Judgment157 Stopping Tests
  157
Current Test

159
- Setting Test Conditions
  159
  - Displaying the Setup Screen (Home Menu)
    159
  - Description of Test Conditions
    160
  - Network
    161
  - Polarity of the Power Supply Line
    162
  - Single Fault Mode (Condition)
    162
  - Upper Limit
    163
  - Lower Limit
    164
  - Judgment Delay (Judge Delay)
    165
  - Test Time
    166
  - Measurement Range
    167
  - Measurement Mode (Measure Mode)
    168
  - Peak Value Display (Display Peakhold)
    170
  - Measurement Check (Measure Check)
    170
  - Offset
    171
  - Voltage Conversion (Conv Voltage)
    172
  - Checking the EUT Operation (Line OUT)
    172
- Starting a Test
  173
  - Operation after a Test Starts
    174
- Finishing the Test and Viewing the Judgment176 Stopping Tests
  176
- Setting Test Conditions
  178
  - Displaying the Setup Screen (Home Menu)
    178
  - Description of Test Conditions
    179
  - Network
    179
  - Polarity of the Power Supply Line
    180
  - Single Fault Mode (Condition)
    181
  - Probe Connection Destination
    182
  - Output from the 110% Terminal (110% OUT)
    183
  - Upper Limit
    184
  - Lower Limit
    185
  - Judgment Delay (Judge Delay)
    186
  - Test Time
    187
  - Measurement Range
    188
  - Measurement Mode (Measure Mode)
    189
  - Voltmeter Band Expansion (Voltmeter Bandwidth)
    190
  - Peak Value Display (Display Peakhold)
    191
  - Measurement Check (Measure Check)
    191
  - Offset
    192
  - Voltage Conversion (Conv Voltage)
    193
  - Checking the EUT Operation (Line OUT)
    193
- Starting a Test
  194
  - Connecting the Test Leads to the EUT
    194
  - Starting a Test
    196
  - Operation after a Test Starts
    197
- Finishing the Test and Viewing the Judgment199
  199
  - Stopping Tests
    199
  - Conditions that Cause a Test to End
    199
  - Judgment Types and Operation
    200
  - Clearing the Judgment Result
    200
Meter Mode

201
- Constructing the Measurement Circuit
  202
- Setting Measurement Conditions
  203
  - Displaying the Setup Screen (Home Menu)
    203
  - Overview of Measurement Conditions
    203
  - Network
    204
  - Measuring Across Terminals a and B (A-B Terminal)
    205
  - SELV Setting
    206
  - Measurement Range
    207
  - Measurement Mode (Measure Mode)
    208
  - Measurement Check (Measure Check)
    208
  - Offset
    209
  - Output from the 110% Terminal (110% OUT)
    210
  - Polarity of the 110% Output
    211
- Executing a Measurement
  212
Auto Test

215
- Auto Test Overview
  215
  - Tests that Auto Test Can Run
    215
  - Programs and Steps
    215
  - Main Functions
    216
- Program Configuration
  217
  - Displaying the Program Editing Screen
    217
  - Creating a Program
    218
  - Changing a Program Name
    218
  - Deleting a Program
    219
- Setting Steps
  220
  - Displaying the Step Editing Screen
    220
  - Editing Steps
    221
- Program Operation Configuration
  224
  - Fail Judgment Operation (FAIL Judgment)
    224
  - Step Interval
    225
  - Step Start Operation (Trigger Source)
    226
  - EUT Power Supply (Line Output)
    227
- Running Auto Tests
  228
  - Running an Auto Test
    228
  - Behavior During the Test
    229
- Finishing the Test and Viewing the Judgment230
  230
  - Stopping Tests
    230
  - Conditions that Cause a Test to End
    230
  - Judgment Types and Operation
    231
  - Clearing the Judgment Result
    231
- Exporting and Importing Programs
  232
  - Exporting Programs to a USB Memory Device
    232
  - Importing Programs from a USB Memory Device
    233
External Control

234
- SIGNAL I/O Connector
  235
  - Pin Arrangement
    235
  - I/O Signal Circuit
    236
  - Input Signal Usage Example
    237
  - Output Signal Usage Example
    237
  - Connecting to the SIGNAL I/O Connector
    238
- Activating and Releasing Interlock
  239
- Recalling from Memory
  241
- Starting and Stopping Tests
  242
  - Starting a Test
    242
  - Stopping a Test
    242
- Monitoring the Test Status
  243
- Monitoring Measurements
  246
- Using Option Products
  248
  - Signal Output from the STATUS out Connector
    248
  - Signal I/O of the REMOTE Connector
    248
Memory Function

249
- Saving and Recalling Test Conditions
  249
  - How to View the Setup Memory Screen
    249
  - Saving to the Setup Memory
    250
  - Checking the Setup Memory Details
    251
  - Recalling the Setup Memory
    252
- Viewing and Saving Test Results
  253
- Viewing and Saving Test Data
  256
  - Viewing Test Data
    256
  - Saving Test Data to a USB Memory Device
    257
  - Deleting Test Data
    257
System Settings

258
- Displaying and Changing CONFIG Settings
  258
  - Panel Settings at Startup (Power On)
    259
  - Operation When There Is no SCPI Communication (Watchdog)
    260
  - Key Lock
    262
  - Calibration Configuration
    263
  - Beep Sound (Beeper)
    264
  - Fail Mode
    265
  - Test Start Settings
    266
  - PASS Judgment Result Hold Time
    267
  - STATUS out Setting (Status Output)
    268
  - Outputting Judgment for each Step (Step END Judgment)
    269
- Displaying/Changing the Interface Settings
  270
- Displaying SCPI Errors
  272
- Setting the Date/Time
  273
- Changing Calibration Date
  274
- Initializing the Settings
  275
  - Restoring the Factory Default Settings
    275
  - Restoring the Reset Settings
    276
- Updating
  277
- Displaying the Device Information
  278
Maintenance

279
- Inspection
  279
- Replacing Components
  283
  - Replacing the Backup Battery
    283
  - Replacing the Fuse
    283
- Periodic Calibration
  284
Specifications

286
- Withstanding Voltage Test Section
  286
- Insulation Resistance Test Section
  289
- Earth Continuity Test Section
  294
- Partial Discharge Test Section
  296
- Leakage Current Test Section
  299
- Interface
  306
- Other Functions
  308
- General Specifications
  310
- External Dimensions
  311
Appendix

315
- Default Settings and Reset Settings
  315
  - Withstanding Voltage (ACW/DCW), Insulation Resistance (IR) Test Conditions
    315
  - Earth Continuity (EC) Test Conditions
    316
  - Partial Discharge (PD) Test Conditions
    316
  - Leakage Current (LC) Test Conditions
    317
  - Auto Test (AUTO) Settings
    318
  - Memory Function
    318
  - CONFIG Settings
    319
  - Interface Settings
    320
- Stray Capacitance of AC Withstanding Voltage Tests
  321
- Timing Charts
  322
  - Contact Check Operation
    322
  - ACW Test (PASS Judgment)
    323
  - ACW Test (FAIL Judgment)
    324
  - ACW Test (Interlock)
    325
- Example of Partial Discharge Test
  326
  - Calculating the Setting
    326
  - Performing a Pre-Test Inspection
    326
  - Performing Tests
    328
  - Performing an Alternative Test
    329
- Options
  330
  - High Voltage Scanner
    330
  - Remote Control Box
    331
  - DIN Adapter Cable
    331
  - High Voltage Test Probe
    332
  - Warning Light Unit
    332
  - Multi-Outlet
    333
  - Brackets
    334
- Troubleshooting
  335
- Index
  337

Kikusui TOS9303LC User Manual (290 pages)

Electrical safety Analyzer

Brand: Kikusui | Category: Measuring Instruments | Size: 10 MB

About Manuals
3
Accessories
4
Product Overview
4
Notations Used in this Manual
5
Safety Precautions
5
Notes on Usage
6
Table of Contents
7
Component Names
12
Safety Precautions for Testing

18
- Lighting of the DANGER LED
  18
- Test Precautions
  18
- Precautions after Output Has Been Turned Off20
  20
  - Estimated Discharge Time
    20
- Remote Control Precautions
  21
- Malfunction Precautions
  21
  - Dangerous Malfunctions
    21
  - Emergency Measures
    21
- Protection Functions
  22
Installation

24
Basic Operation

42
- Basic Panel Operations
  42
  - Switching Menus
    42
  - Using the Function Keys
    43
  - Inputting Numbers and Characters
    45
  - Changing Values
    46
- Selecting the Test Mode
  47
Patient Leakage Current

47
- Selecting the Test Mode
  48
Withstanding Voltage and Insulation Resistance Tests

49
- Setting Test Conditions
  49
  - Displaying the Setup Screen (Home Menu)
    49
  - Description of Test Conditions
    50
  - Test Voltage
    51
  - Limit Voltage
    52
  - Start Voltage
    53
  - Frequency
    54
  - Upper Limit
    55
  - Lower Limit
    56
  - Unit of Criteria (Judge Type)
    57
  - Auto Setting of the Judgment Delay (Delay Auto)
    58
  - Test Time
    60
  - Voltage Rise Time
    61
  - Voltage Fall Time
    62
  - Discharge Time
    63
  - Discharge When Interlock Is Activated (Discharge Interlock)
    64
  - Current Detection Response Speed (Filter)
    65
  - Grounding Mode (GND)
    66
  - Current Measurement Mode (Current RMS)
    68
  - Voltage Measurement Mode (Volt Measure)
    69
  - Peak Value Display (Display Peakhold)
    70
  - Using the Low-Pass Filter
    71
  - Offset (Offset Real, Offset Imag)
    72
  - Offset
    73
  - Checking the Scanner Contact (Contact Check)
    74
  - Setting Scanner Channels (Edit)
    75
  - Opening the Scanner (All Open)
    76
- Starting a Test
  77
- Finishing the Test and Viewing the Judgment
  83
Earth Continuity Test

85
- Setting Test Conditions
  85
  - Displaying the Setup Screen (Home Menu)
    85
  - Description of Test Conditions
    86
  - Test Current
    86
  - Limit Current
    87
  - Frequency
    87
  - Upper Limit
    88
  - Lower Limit
    89
  - Test Time
    90
  - Current Rise Time
    91
  - Current Fall Time
    91
  - Terminal Wiring Method (Terminals Wire)
    92
  - Contact Check
    93
  - Peak Value Display (Display Peakhold)
    94
  - Offset
    95
- Starting a Test
  96
- Finishing the Test and Viewing the Judgment100
  100
  - Stopping Tests
    100
  - Conditions that Cause a Test to End
    100
  - Judgment Types and Operation
    101
  - Clearing the Judgment Result
    101
Touch Current Test

102
- Setting Test Conditions
  102
  - Displaying the Setup Screen (Home Menu)
    102
  - Description of Test Conditions
    103
  - Network
    104
  - Polarity of the Power Supply Line
    105
  - Single Fault Mode (Condition)
    106
  - Probe Connection Destination
    107
  - Output from the 110% Terminal (110% OUT)
    108
  - Upper Limit
    109
  - Lower Limit
    110
  - Judgment Delay (Judge Delay)
    111
  - Test Time
    112
  - Measurement Range
    113
  - Measurement Mode (Measure Mode)
    115
  - Voltmeter Band Expansion (Voltmeter Bandwidth)
    116
  - Peak Value Display (Display Peakhold)
    117
  - Measurement Check (Measure Check)
    117
  - Offset
    118
  - Voltage Conversion (Conv Voltage)
    119
  - Checking the EUT Operation (Line OUT)
    119
- Starting a Test
  120
  - Connecting the Test Leads to the EUT
    120
  - Starting a Test
    121
  - Operation after a Test Starts
    122
- Finishing the Test and Viewing the Judgment124
  124
  - Stopping Tests
    124
  - Conditions that Cause a Test to End
    124
- Finishing the Test and Viewing the Judgment166
  124
  - Judgment Types and Operation
    125
  - Clearing the Judgment Result
    125
Protective Conductor Current Test

126
- Setting Test Conditions
  126
  - Displaying the Setup Screen (Home Menu)
    126
  - Description of Test Conditions
    127
  - Network
    128
  - Polarity of the Power Supply Line
    129
  - Single Fault Mode (Condition)
    129
  - Upper Limit
    130
  - Lower Limit
    131
  - Judgment Delay (Judge Delay)
    132
  - Test Time
    133
  - Measurement Range
    134
  - Measurement Mode (Measure Mode)
    135
  - Voltmeter Band Expansion (Voltmeter Bandwidth)
    136
  - Peak Value Display (Display Peakhold)
    137
  - Measurement Check (Measure Check)
    137
  - Offset
    138
  - Voltage Conversion (Conv Voltage)
    139
  - Checking the EUT Operation (Line OUT)
    139
- Starting a Test
  140
  - Operation after a Test Starts
    141
- Finishing the Test and Viewing the Judgment143
  143
  - Stopping Tests
    143
  - Conditions that Cause a Test to End
    143
  - Judgment Types and Operation
    144
  - Clearing the Judgment Result
    144
- Setting Test Conditions
  145
  - Displaying the Setup Screen (Home Menu)
    145
  - Description of Test Conditions
    146
  - Network
    146
  - Polarity of the Power Supply Line
    147
  - Single Fault Mode (Condition)
    148
  - Probe Connection Destination
    149
  - Output from the 110% Terminal (110% OUT)
    150
  - Upper Limit
    151
  - Lower Limit
    152
  - Judgment Delay (Judge Delay)
    153
  - Test Time
    154
  - Measurement Range
    155
  - Measurement Mode (Measure Mode)
    156
  - Peak Value Display (Display Peakhold)
    158
  - Measurement Check (Measure Check)
    158
  - Offset
    159
  - Voltage Conversion (Conv Voltage)
    160
  - Checking the EUT Operation (Line OUT)
    160
- Starting a Test
  161
  - Connecting the Test Leads to the EUT
    161
  - Starting a Test
    163
  - Operation after a Test Starts
    164
  - Stopping Tests
    166
  - Conditions that Cause a Test to End
    166
  - Judgment Types and Operation
    167
  - Clearing the Judgment Result
    167
Meter Mode

168
- Constructing the Measurement Circuit
  169
- Setting Measurement Conditions
  170
  - Displaying the Setup Screen (Home Menu)
    170
  - Overview of Measurement Conditions
    170
  - Network
    171
  - Measuring Across Terminals a and B (A-B Terminal)
    172
  - SELV Setting
    173
  - Measurement Range
    174
  - Measurement Mode (Measure Mode)
    175
  - Measurement Check (Measure Check)
    175
  - Offset
    176
  - Output from the 110% Terminal (110% OUT)
    177
  - Polarity of the 110% Output
    178
- Executing a Measurement
  179
Auto Test

182
- Auto Test Overview
  182
  - Tests that Auto Test Can Run
    182
  - Programs and Steps
    182
  - Main Functions
    183
- Program Configuration
  184
  - Displaying the Program Editing Screen
    184
  - Creating a Program
    185
  - Changing a Program Name
    185
  - Deleting a Program
    186
- Setting Steps
  187
  - Displaying the Step Editing Screen
    187
  - Editing Steps
    188
- Program Operation Configuration
  189
  - Fail Judgment Operation (FAIL Judgment)
    189
  - Step Interval
    190
  - Step Start Operation (Trigger Source)
    191
  - EUT Power Supply (Line Break)
    192
- Running Auto Tests
  193
  - Running an Auto Test
    193
  - Behavior During the Test
    194
- Finishing the Test and Viewing the Judgment195
  195
  - Stopping Tests
    195
  - Conditions that Cause a Test to End
    195
  - Judgment Types and Operation
    196
  - Clearing the Judgment Result
    196
- Exporting and Importing Programs
  197
  - Exporting Programs to a USB Memory Device
    197
  - Importing Programs from a USB Memory Device
    198
External Control

199
- SIGNAL I/O Connector
  200
  - Pin Arrangement
    200
  - I/O Signal Circuit
    201
  - Input Signal Usage Example
    202
  - Output Signal Usage Example
    202
  - Connecting to the SIGNAL I/O Connector
    203
- Activating and Releasing Interlock
  204
- Recalling from Memory
  206
- Starting and Stopping Tests
  207
  - Starting a Test
    207
  - Stopping a Test
    207
- Monitoring the Test Status
  208
- Monitoring Measurements
  211
  - Monitoring Current Waveforms
    211
  - Monitoring Voltage Waveforms
    211
- Using Option Products
  212
  - Signal Output from the STATUS out Connector.212
    212
  - Signal I/O of the REMOTE Connector
    212
Memory Function

213
- Saving and Recalling Test Conditions
  213
  - How to View the Setup Memory Screen
    213
  - Saving to the Setup Memory
    214
  - Checking the Setup Memory Details
    215
  - Recalling the Setup Memory
    216
- Saving and Viewing Test Results
  217
System Settings

219
- Displaying and Changing CONFIG Settings
  219
  - Panel Settings at Startup (Power On)
    220
  - Operation When There Is no SCPI Communication (Watchdog)
    221
  - Screen Saver
    222
  - Key Lock
    223
  - Calibration Configuration
    224
  - Beep Sound (Beeper)
    225
  - Fail Mode
    226
  - Test Start Settings
    227
  - PASS Judgment Result Hold Time
    228
  - STATUS out Setting (Status Output)
    229
  - Outputting Judgment for each Step (Step END Judgment)
    230
- Displaying/Changing the Interface Settings
  231
- Displaying SCPI Errors
  233
- Setting the Date/Time
  234
- Initializing the Settings
  235
  - Restoring the Factory Default Settings
    235
  - Restoring the Reset Settings
    236
- Updating
  237
- Displaying the Device Information
  238
Maintenance

239
- Inspection
  239
- Replacing Components
  243
  - Replacing the Backup Battery
    243
  - Replacing the Fuse
    243
- Periodic Calibration
  244
Specifications

246
- Withstanding Voltage Test Section
  246
- Insulation Resistance Test Section
  249
- Earth Continuity Test Section
  253
- Leakage Current Test Section
  255
- Interface
  262
- Other Functions
  263
- General Specifications
  265
- External Dimensions
  266
Appendix

269
- Default Settings and Reset Settings
  269
  - Withstanding Voltage (ACW/DCW), Insulation Resistance (IR) Test Conditions
    269
  - Earth Continuity (EC) Test Conditions
    270
  - Leakage Current (LC) Test Conditions
    270
  - Auto Test (AUTO) Settings
    272
  - Memory Function
    272
  - CONFIG Settings
    273
  - Interface Settings
    274
- Stray Capacitance of AC Withstanding Voltage Tests
  275
- Timing Charts
  276
  - Contact Check Operation
    276
  - ACW Test (PASS Judgment)
    277
  - ACW Test (FAIL Judgment)
    278
  - ACW Test (Interlock)
    279
- Options
  280
  - High Voltage Scanner
    280
  - Remote Control Box
    281
  - DIN Adapter Cable
    281
  - High Voltage Test Probe
    282
  - Warning Light Unit
    282
  - Multi-Outlet
    283
  - Brackets
    284
- Troubleshooting
  285
- Index
  287

Kikusui Categories

Power Supply Test Equipment Measuring Instruments Racks & Stands Extender

More Kikusui Manuals

Kikusui TOS9303LC Safety Analyzer Manuals

Kikusui TOS9303LC User Manual (340 pages)

Table of Contents

Safety Precautions for Testing

Installation

Basic Operation

Withstanding Voltage and Insulation Resistance Tests

Patient Leakage Current

Test

Earth Continuity Test

Partial Discharge Test

Touch Current Test

Current Test

Meter Mode

Auto Test

External Control

Memory Function

System Settings

Maintenance

Specifications

Appendix