Sign In
Upload
Manuals
Brands
Fluke Manuals
Test Equipment
6135A/PMU
Fluke 6135A/PMU Manuals
Manuals and User Guides for Fluke 6135A/PMU. We have
1
Fluke 6135A/PMU manual available for free PDF download: Operator's Manual
Fluke 6135A/PMU Operator's Manual (160 pages)
Calibration System
Brand:
Fluke
| Category:
Test Equipment
| Size: 16.7 MB
Table of Contents
Table of Contents
3
Introduction and Specifications
7
Introduction
7
About this Chapter
7
Standard Accessories
9
Safety Information
10
Specifications
10
About the Manual Set
10
Contact Fluke Calibration
11
Performance Verification and Repair Information
11
Calibration System Overview
12
Components of the Calibration System
14
Client PC
14
Server PC
15
6135A Three Phase Power Standard
16
Microsemi GPS Receiver
18
6135A/PMU System Timing Unit
19
6135A/PMU System Software Status Panel
21
Pmucal Software
22
Overview
22
Monitor Screen
22
Navigation Menu
23
The System Status Panel
24
General Specifications
25
Input Power
25
Dimensions
25
Environment
25
Standard and Agency Approvals
25
Electrical Source Accuracy Specifications
25
Performance Specifications for IEEE C37.118.1A-2014 Tests
25
PMU Test: Limits to Range of Influence Quantities
26
General Test Limits
26
Steady State Tests
26
Modulation Tests
26
Frequency Ramp Tests
26
Input Step Change Tests
26
Installation Instructions
27
About this Chapter
29
Unpack and Inspect
29
Install the Calibration System
30
Pre-Installation Preparation
30
Installation Procedure
31
Install the Pmucal Software
31
Configure the Client PC
32
Configure Windows Firewall
32
Network Connection Instructions
35
Direct Connection Instructions
36
Set up the File Storage Directory
40
Install the Test Files
42
Software Operation
43
About this Chapter
45
UUT Calibration Procedure
45
Overview
45
Calibration Procedure Information
46
Calibration Compliance to IEEE C37.118.1A-2014
47
About Synchrophasor Calibration
48
Time to Complete a UUT Calibration
49
Calibration Test Measurements
49
Calibration Procedure Preparation
50
UUT Configuration
50
UUT and Simulator Personality Profiles
50
UUT Personality Profile
50
Simulator Personality Profile
52
Testing Methods
53
Automated Testing
55
General and Custom Interactive Test Methods
55
General Interactive Testing
56
Custom Interactive Testing
56
Interactive Test Sequence of Events
57
Run the Test
57
Set up the Interactive Graph
58
Analyze the Data on the Interactive Graph
58
Modes of Operation
59
Simulation Mode
60
PMU Test Mode
60
Standard Compliance Tests and Test Files
60
Standard Compliance Tests and Subtests
62
Steady State Compliance Tests
62
Dynamic Compliance Tests
63
Standard Compliance Tests File Naming Convention
64
Automated Test List Files
66
Test Results and Results Files
66
About Result Files and the Active Results File
66
Results Files Naming Convention
67
Result File Save Options
68
Results File Storage Directory
68
Raw Data Files
69
Test Report and Calibration Report
69
UUT Calibration Setup
71
About this Chapter
73
Safety Information
73
General Operation Information
74
Turn on the Calibration System
74
Turn off the Calibration System
74
Calibration System Warm-Up
74
Connect the Calibration System to a UUT
74
Prepare the UUT for Calibration
75
Current Connections
76
Voltage Connections
77
UUT Data Cable Connection
78
GPS Signal Cable Connection
78
Communicate with the UUT
79
Set up a UUT Personality Profile
81
Configure the UUT Phase Order
84
UUT Connection Test
86
Automated Testing
93
About this Chapter
95
Automated Testing Overview
95
Getting Started
95
Run an Automated Test
96
Incomplete Tests
98
Make a New Automated Test
100
General Testing
103
About this Chapter
105
General Testing
105
Test Configuration Instructions
108
General Test Parameters
108
Test Type Parameter
109
Test Parameters
109
Steady State Test Parameters
110
Frequency Ramp Test Parameters
112
Modulation Test Parameters
113
Step Test Parameters
115
Measurement Latency Test Parameters
117
Run a Single Test
117
Run a Custom Interactive Test
118
Interactive Graphs, Results, and Reports
119
Introduction
121
Interactive Graph
121
Graph Configuration Window
122
Make an Interactive Graph
122
Example Interactive Graph Configurations
125
One Source and One Input Graph Configuration Example
125
Two Sources and One Input Graph Configuration Example
125
Two Source and Two Inputs Graph Configuration Example
126
Y-Axis Analysis Results Configuration Example
127
Change the View of an Interactive Graph
128
Zoom-In and Zoom-Out of a Plot
128
Undock and Dock a Panel
129
Change the Displayed Data
130
Change the Look of the Plot
130
Measurement Latency Test Results
131
Test Results
132
Test Results Viewer
132
View Test Results in the Results Viewer
132
Log of Tests
133
Test Reports
134
Report Templates
134
Create One Report
135
Create Multiple Reports
135
View a Report
137
Troubleshooting, Maintenance, and Care
139
About this Chapter
141
Troubleshooting
142
General
142
6135A/PMU System Timing Unit
142
Server PC
143
6135A Three Phase Power Standard
143
GPS Receiver
144
Network
144
Calibration Software
144
Uut
145
Test Reports
147
Cleaning
148
Performance Verification and Repair Information
148
Performance Verification
149
About this Chapter
151
Prerequisites
151
Equipment Required
151
Procedures
151
Verify Signal Alignment with the UTC
151
Verify the Accuracy of the Timing Inputs
152
Verify Step Timing Accuracy
153
L1V Test
154
L2V Test
155
L3V Test
156
A Glossary
157
Advertisement
Advertisement
Related Products
Fluke 6135A/PMUCAL
Fluke 6100B
Fluke 6105A
Fluke 6109A
Fluke 6101B
Fluke 6106A
Fluke 685
Fluke 683
Fluke 682
Fluke 680
Fluke Categories
Measuring Instruments
Test Equipment
Multimeter
Thermometer
Laboratory Equipment
More Fluke Manuals
Login
Sign In
OR
Sign in with Facebook
Sign in with Google
Upload manual
Upload from disk
Upload from URL