Full HD Speed Dome IP Camera Installation Guide Indoor / Outdoor Version 1.3 00P6NH720ZXSEA3...
Page 2
Installation Guide Preface The information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice. Notice This manual provides the installation information for the indoor integrated high speed dome.
Page 3
Installation Guide This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002 / 96 / EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Installation Guide Warnings and Cautions Handle the camera carefully Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage. Installing electricity wiring carefully Ask qualified personnel of electrical wiring for the installation. Please note that input electricity to the unit is at tolerance of DC 12V / AC 24V ±...
Page 5
Installation Guide Never face the camera towards the sun Do not aim the camera at bright objects. Whether the camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise, the camera may be smeared or damaged.
Installation Guide Introduction The Full HD Speed Dome IP Camera is designed to deliver superb performance and durability with an intelligent and stylish housing that is suitable in any security and surveillance installation. Standard Package Contents Before proceeding, please check the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact dealer for assistance.
Page 8
Installation Guide Outdoor Model M3 Standard Screw (x1) M3 Security Screw (x1)* M5 Standard Screw (x1) M5 Security Screw (x1)* Camera Body with Outdoor Mount Kit Quick Guide Waterproof Rubber CD: Operation Manuals Optical Cover Lubricant Security Torx* *Optional: For Vandal Proof Cover only.
Installation Guide Camera Cable Connections Before installing or connecting the Dome Camera, please refer to this section and complete preparations for dome setups and various switch settings. There will be a PE cloth sheet covered inside the dome cover and a lens cap on the lens for shipping protection.
Installation Guide Cable Requirements For operation, the network Speed Dome IP Camera requires power cable and RJ-45 as described below: 3.2.1 Power Connection Please refer to the illustrations below to connect power core through the supplied power adaptor. Definition AC 24- AC 24+ 3.2.2 Ethernet Cable Connection...
Installation Guide Dome Camera Installation Basing on user’s installation environments, the Dome Camera can be installed on ceiling, on wall or on pole. In the following sections, various Dome Camera installation accessories, installation methods and installation procedures will be described in detail. In addition, the next section will provide the Dome Camera’s dimensions for reference before installation.
Installation Guide Optional Accessories Dome Camera Accessories Transparent / Vandal Proof Transparent Cover (Standard) Vandal Proof Cover (Optional) Power Adapter 77H07-A1015 (Input: 100~115 VAC / Output: 24 VAC 36 VA) 77H07-A2015 (Input: 220~230 VAC / Output: 24 VAC 36 VA) NOTE: When wiring, make sure the G / Y wire (Ground) inserted into the mid-pin of the terminal block.
Page 13
Installation Guide Mounting Accessories Hard Ceiling Mount (Standard Equipment) For Hard Ceiling Installation. Height: 24.01 mm (0.95 inches); Diameter of the three holes: 4.2 mm (0.17 inches); Diameter of the bracket: 103.1 mm (4.1 inches); Weight: 65 g (0.14 Ibs) In-Ceiling (T-Bar) Mount For In-Ceiling Installation.
Page 14
Installation Guide Indoor Mounting Kit (IMK) Height (with Hard Ceiling Mount): 75.1 mm (3.0 inches); Height: 58 mm (2.3 inches); Total Width: 110.66 mm (4.4 inches); Weight: 260 g (0.56 Ibs) Standard Pendent Mount White; 348×104×138.6 mm (13.7×4.1×5.5 inches); 1.5 kg (3.3 lbs); Diameter: 45 mm (1.8 inches).
Page 15
Installation Guide Compact Pendent Mount 184×104×115.2 mm (7.24×4.09×4.54 inches); 0.6kg (1.2 lbs). Supplied with rubber washer-8 x1, pendent tube washer x1, spring washer-8 x1 and M8x12 screw x1. Straight Tube Iron; Height: 250 / 500 mm (9.8 / 19.7 inches); Diameter: 50 mm (2 inches) 1 kg (2.2 lbs) / 1.8 kg (4 lbs).
Page 16
Installation Guide Swan Tube For mounting with Swan Tube. White; Iron, Dimension: 835 x 300 mm (32.9×11.8 inches); Diameter: 45 mm (1.8 inches); Weight: 3.8 kg (8.4 lbs). Supplied with pendent tube washer x1, rubber washer-8 x1, waterproof rubber x1, spring washer-8 x1 and M8x12 screw x1.
Page 17
Installation Guide Corner Standard Mounting Plate 222(L) x 204(W) x 117(D) mm (8.7 x 8 x 4.6 inches); 2 kg (4.4 lbs). Supplied with washer-8 x4, spring washer-8 x4, M8x16 screw x4, and M8 nut x4. Pole Thin Direct Mounting 232(L) x 136(W) x 60(D) mm (9.1 x 5.4 x 2.4 inches);...
Page 18
Installation Guide Pole Wide Direct Mounting 270(L) x 170(W) x 60(D) mm (10.6 x 6.7 x 2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); Weight: 1 kg (2.2 lbs). Supplied with M8x16 screw x4, washer x4, stainless steel straps x4 and spring washer-8 x4. Corner Thin Box Mounting 300(L) x 164(W) x 222(D) mm (11.8 x 6.5 x 8.7 inches);...
Page 19
Installation Guide Corner Wide Box Mounting 232(L) x 234(W) x 210(D) mm (9.1 x 9.2 x 8.3 inches); Weight: 2.7 kg (6 lbs). Supplied with M8x16 screw x4, washer-8 x4, and spring washer-8 x4. Pole Thin Box Mounting 291(L)×136(W)×242 (D) mm (11.5×5.4×9.5 inches); 3.1 kg (6.9 lbs). Supplied with M8x16 screw x4, washer-8 x4, spring washer x4 and stainless steel straps x4.
Page 20
Installation Guide Pole Wide Box Mounting 270(L)×166(W)×155(D) mm (10.6×6.5×6.1 inches); 3.2 kg (7.1 lbs). Supplied with M8x16 screw x4, washer-8 x4, spring washer-8 x4 and stainless steel straps x4. Wall Box Mounting 270(L) x 166(W) x 95(D) (10.6 x 6.5 x 3.7 inches); Weight: 2.2 kg (4.84 lbs). Supplied with M8x16 screw x4, washer-8 x4 and spring washer-8 x4.
Page 21
Installation Guide Stainless Steel Straps For fixing Pole Direct Mounting / Pole Box on the pole. Length: 650 mm (25.6 inches); Width: 12.7mm; Weight: 50 g (0.1 lb) Stainless Strap Cutter For tension, cut and crimp stainless steel straps. Weight: 1.4 kg (3.1 lbs). Suitable for straps width: 1/2”, 5/8”, 3/4”...
Installation Guide Ceiling Mount Generally, there are three kinds of Dome Camera ceiling mounting methods: hard-ceiling, in-ceiling and mounting with Straight Tube. Refer to the following sections for more details. The following figures show how cables connect to the Dome Camera in different ways.
Page 23
Installation Guide STEP 2 In the marked locations, drill each hole slightly smaller than the supplied Screw Anchors, and put supplied Anchors into these drilled holes. Then Fasten the Hard Ceiling Mount with the three supplied Self-tapping Screws. STEP 3 Thread the Data Cable and Ethernet cable through the center hole of the Mount and connect the cable to the camera body.
Page 24
Installation Guide STEP 6 After installing the Camera on the Hard Ceiling Mount, put the Dome Cover back, and use a flat screw drive to fasten two supplied Flat Screws on the Dome Cover. STEP 7 Fasten the supplied Standard Screw (Security Screw for Vandal Proof Dome) on the Dome Cover.
Installation Guide 4.3.2 In-Ceiling (T-Bar) Mounting Here lists the items and tools needed to mount the Dome Camera into the ceilings. The supplied items are all in the Dome Camera package. Package Contents: Lock Bar x1 M3x6 Screw x2 ...
Page 26
Installation Guide STEP 2 Tighten the screw at the side of the Fixing Plate. Finishes install Camera on T-Bar Bottom Mount. STEP 3 Place the Ceiling Sticker on the ceiling plate, and cut the circle part out of the ceiling. STEP 4 Disassemble the wings from the In-Ceiling (T-Bar) Mount by loosening three screws counterclockwise...
Page 27
Installation Guide STEP 5 Put up the T-Bar Bracket into the ceiling opening and fix the In-Ceiling (T-Bar) Mount on the ceiling by tightening three screws clockwise. STEP 6 When screwing, the Wings will get approached to the ceiling board until it is completely flush with the board.
Page 28
Installation Guide STEP 10 Fix the Trim Ring to the T-Bar Bracket.
Installation Guide 4.3.3 Ceiling Mounting with Indoor Mounting Kit Indoor Mounting Kit is able to work with other ceiling mounting accessories, such as Standard Pendent Mount, Compact Pendent Mount, Straight Tube and Swan Tube. Here lists the items and tools needed to mount the Dome Camera onto the Indoor Mounting Kit.
Page 30
Installation Guide STEP 2 Install the Camera on the Indoor Mounting Kit by turning the Camera clockwise. Then tighten the screw on the side of the Fixing Plate. STEP 3 After installing the Camera on the Hard Ceiling Mount, put the Dome Cover back, and use a flat screw drive to fasten two supplied Flat Screws on the Dome Cover.
Installation Guide 4.3.4 Ceiling Mounting with Straight Tube The Straight Tube is available in different length: 25 cm and 50 cm. Package Contents: M8x12 Screw x1 Spring Washer-8 x1 Pendent Tube Washer x1 Rubber Washer-8 x1 Waterproof Rubber x1 ...
Page 32
Installation Guide 7) Mount the Dome Camera to the Mounting Kit. (Ensure the Dome Camera is fixed completely, and the thread holes on the Lock Screw Plate and Mounting Kit are aligned). Afterwards, screw the supplied M5 standard screw / security screw, as shown in the picture.
Installation Guide Wall Mount The Dome Camera can be mounted on the wall with Compact Pendent Mount, Standard Pendent Mount and Wall Box. Please follow the installation instructions below for mounting the Dome Camera via different ways. 4.4.1 Swan Tube Package Contents: M8x12 Screw x1 ...
Installation Guide 4.4.2 Compact Pendent Mount Package Contents: Rubber Washer-8 x1 Pendent Tube Washer x1 Spring Washer-8 x1 M8x12 Screw x1 Items Needed: Dome Camera Power Cable Ethernet Cable Compact Pendent Mount and equipped items (optional accessory) ...
Page 36
Installation Guide 7) Run the cable(s) through the Compact Pendent Mount. NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. The sponge can be placed in two ways as shown in the illustrations below. Sponge Sponge 8) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to...
Installation Guide 4.4.3 Standard Pendent Mount Package Contents: M8x12 Screw x1 Spring Washer-8 x1 Pendent Tube Washer x1 Rubber Washer-8 x1 Sponge x2 Items Needed: Dome Camera Power Cable Ethernet Cable Standard Pendent Mount and equipped items (optional accessory) ...
Page 38
Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. Refer to the illustrations in section 4.4.2 Compact Pendent Mount > Step 4. 5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to the Standard Pendent Mount with the supplied screws and washers.
Installation Guide 4.4.4 Wall Box Mounting Package Contents: M8x16 Screw x4 Washer-8 x4 Spring Washer-8 x4 Items Needed: Dome Camera Power Cable Ethernet Cable Standard / Compact Pendent Mount and equipped items (optional accessory) Wall Box Mounting (optional accessory) ...
Page 40
Installation Guide 5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to the Standard / Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera. 7) Join the Dome Camera to the Mounting Kit with the supplied screw and washers.
Installation Guide Corner Mount 4.5.1 Corner Standard Mounting Plate / Corner Plate Mini Package Contents: Washer-8 x4 Spring Washer-8 ×4 M8x16 Screw x4 M8 Nut x4 Items Needed: Dome Camera Power Cable Ethernet Cable ...
Page 42
Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. Refer to the illustrations in section 4.4.2 Compact Pendent Mount > Step 4) Attach the Waterproof Rubber to the Standard / Compact Pendent Mount. 5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to the Standard / Compact Pendent Mount with the supplied screws and washers.
Installation Guide 4.5.2 Corner Thin / Wide Box Mounting Package Contents: M8x16 Screw x4 Washer-8 x4 Spring Washer-8 x4 Items Needed: Dome Camera Power Cable Ethernet Cable Standard / Compact Pendent Mount and equipped items (optional ...
Page 44
Installation Guide 4) Attach the Waterproof Rubber to the Standard / Compact Pendent Mount. 5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to the Standard / Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera.
Installation Guide Pole Mount 4.6.1 Pole Thin / Wide Direct Mounting Package Contents: Stainless Steel Straps x4 M8x16 Screw x4 Washer x4 Spring Washer-8 x4 Items Needed: Dome Camera Power Cable Ethernet Cable Standard / Compact Pendent Mount and equipped items (optional ...
Page 46
Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. Refer to the illustrations in section 4.4.2 Compact Pendent Mount > Step 4) Attach the Waterproof Rubber to the Standard / Compact Pendent Mount. 5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to the Standard / Compact Pendent Mount with the supplied screws and washers.
Installation Guide 4.6.2 Pole Thin / Wide Box Mounting Package Contents: M8x16 Screw x4 Washer-8 x4 Spring Washer x4, Stainless Steel Straps x4 Items Needed: Dome Camera Power Cable Ethernet Cable Standard / Compact Pendent Mount and equipped items (optional ...
Page 48
Installation Guide 4) Attach the Waterproof Rubber to the Standard / Compact Pendent Mount. 5) Thread the cable(s) through the Mounting Kit and join the Mounting Kit to the Standard / Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera.
Need help?
Do you have a question about the NH720 and is the answer not in the manual?
Questions and answers