Subscribe to Our Youtube Channel
Related Manuals for DynaColor S3
Summary of Contents for DynaColor S3
-
Page 1: Installation Guide
Integrated High Speed Dome Camera Outdoor Installation Guide Version 3.6 00P6H8020ZXSEC6... - Page 2 Installation Guide Preface Information given in this manual was current when published. The company reserves the right to revise and improve its products. All specifications are subject to change without notice. Notice This manual provides installation information for the outdoor integrated high speed dome.
- Page 3 Installation Guide This symbol on the product or on its packaging indicates that this product shall not be treated as household waste in accordance with Directive 2002/96/EC. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
-
Page 4: Warnings And Cautions
Installation Guide Warnings and Cautions • Handle the camera carefully Do not abuse the camera. Avoid striking, shaking, etc. The camera could be damaged by improper handing or storage. • Installing electricity wiring carefully Ask qualified personnel of electrical wiring for the installation. Please note that input electricity to the unit is at tolerance of DC12V/AC24V ±... -
Page 5: Table Of Contents
Installation Guide Table of Contents Introduction........................6 Standard Package Contents ..................7 Camera Setups and Cable Connections ..............9 Preparations for Dome Camera Setups ................9 Dome Camera Setups....................12 3.2.1 Switch/Connector Definition ................12 3.2.2 Communication Switch Setting ............... 13 3.2.3 ID Setting......................14 3.2.4 Camera Control Protocol Setting .............. - Page 6 Installation Guide Signal Distribution ......................48 System Integration ....................49 Using Pelco Keyboard....................49 Using Philips Allegiant Keyboard................... 50 Appendix A: Technical Specification ................51...
-
Page 7: Introduction
In addition, large set of built-in protocols provide connectivity to other surveillance systems. The built-in protocols include DynaColor, Pelco, VCL, Philips, AD-422, etc., which allow the Integrated High Speed Dome Camera to be integrated with other suppliers' surveillance systems. -
Page 8: Standard Package Contents
Installation Guide Standard Package Contents Before proceeding, please check the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance. Analog Model Dome Camera with Data Cable for Power Supply, Video, Alarm and RS-485 Outdoor Mount Kit (AC 24V) - Page 9 Installation Guide Network Model Dome Camera with Data Cable for Power Supply, Video, Audio and Alarm Outdoor Mount Kit (AC 24V) M3 Standard Screw (x1) Lubricant M3 Security Screw (x1) M5 Standard Screw (x1) Waterproof Rubber M5 Security Screw (x1) Security Torx Quick Guide Optical Cover...
-
Page 10: Camera Setups And Cable Connections
Installation Guide Camera Setups and Cable Connections Before installing or connecting the dome camera, please refer to this section and complete preparations for dome setups and various switch settings. Preparations for Dome Camera Setups The following installation procedure is for the outdoor dome equipped with the sunshield housing. - Page 11 Installation Guide STEP 4 Attach the dome cover to the camera body. Before doing that, apply some lubricant on the cover’s water-proof rubber make installation process smoother. Note that the tiny protrusion on the dome cover must align with one of the four holes on the dome body.
- Page 12 Installation Guide STEP 7 Set the switches located on the bottom of the dome body. Refer to section 3.2 Dome Camera Setups for detailed information about various switch setting.
-
Page 13: Dome Camera Setups
Installation Guide Dome Camera Setups Before connecting the Dome Camera to other devices of CCTV system, please complete the Dome Camera’s ID and communication switch settings. These switches are located on the bottom of the Dome Camera. 3.2.1 Switch/Connector Definition Please refer to the diagrams and tables accompanied with for use of each switch/connector. -
Page 14: Communication Switch Setting
Installation Guide 3.2.2 Communication Switch Setting Communication Switch SW 1 RS-485 Setting SW 2 Termination SW 3 Line Lock SW 4 Factory Default Reset SW 5 Reserved SW 6 RS-485 is the interface that communicates the dome camera and its control device;... -
Page 15: Id Setting
Installation Guide 3.2.3 ID Setting Please change the analog Dome Camera’s ID if there is more than one Dome Camera on the same installation site. Use the switch to change your Speed Dome Camera’s ID by turning the arrow to the desired number respectively. For instance, if the camera’s ID is 123, the ID switch should be set as below. -
Page 16: Camera Control Protocol Setting
Installation Guide 3.2.4 Camera Control Protocol Setting Define the protocol you are going to use basing on the devices of your surveillance system. Generally, use one protocol even the devices are provided from different manufacturers. Use the switch to set your camera control protocol and the baud rate. -
Page 17: Cables And Connections
Installation Guide Cables and Connections The Dome Camera is supplied with one integrated 22-pin Data Cable for connecting with the power, video, and RS-485/audio input & audio output cables. Please read the following sections thoroughly before making connections. 3.3.1 Cable Requirements For operation, the Integrated High Speed Dome Cameras require video, RS-485 and power cables as described below: •... -
Page 18: Network Model
Installation Guide NOTE: Be careful not to pull the cables improperly during installation. Additionally, it is suggested to fasten the cables after cable connection is completed. Furthermore, when wiring the AC 24V power cable, make sure the Ground wire is inserted into the mid-pin of the terminal block. -
Page 19: Analog Model
Installation Guide Analog Model The analog Dome Camera’s 22-pin connector definition is listed as below. Definition Cable Definition Cable AC 24-1/DC (＋) 20AWG ALM-1 ALM NC ALM-3 AC 24-2/DC (－) 20AWG ALM-2 ALM NO ALM-4 20AWG ALM-5 ALM COM ALM-6 ALM-7 ALM-8 24AWG... -
Page 20: Rs-485 Connector Definition
Installation Guide 3.3.4 RS-485 Connector Definition RS-485 is the interface that communicates the Dome Camera and its control device. Please connect the control keyboard to the Dome Camera through the terminal block. The recommended cables for RS-485 communication are CAT 5 cables; maximum cable length for over 24-gauge wire is 4000 feet (1219 meters). -
Page 21: Ethernet Cable Connection
Installation Guide Insert the terminal into the pin holes connector housing, with hook outward, as indicated in the figure. To unlock the terminal, press the hook, as indicated in the figure, with a proper tool and pull it out gently. Connect the 22-pin connector to the Dome Camera. -
Page 22: Dome Camera Installation
Installation Guide Dome Camera Installation Basing on user’s installation environments, the Dome Camera can be installed on ceiling, on wall or on pole. In the following section, various Dome Camera’s installation accessories, installation methods and installation procedures will be described in detail. In addition, the next section will provide the Dome Camera’s dimensions for your reference before installation. -
Page 23: Optional Accessories
Installation Guide Optional Accessories Dome Camera Accessories Sunshield Height: 129.5 mm (5.05 inches); Diameter: 190 mm (7.48 inches); 0.15 kg (0.33 lbs) Transparent/Vandal Proof/Smoke Cover Diameter: 147 mm (5.8 inches) Security Screw Set (equipped with Vandal Proof Cover) Power Adapter 77H07-A1030 (Input: 100~115VAC/Output: 24VAC 72VA) 77H07-A2030 (Input: 220~230VAC/Output: 24VAC 72VA) NOTE: When wiring, make sure the G/Y wire (Ground) inserted into the... - Page 24 Installation Guide Mounting Accessories Standard Pendent Mount White; 348×104×138.6 mm (13.7×4.1×5.5 inches); 1.5 kg (3.3 lbs); Diameter: 45 mm (1.8 inches). Supplied with M8x12 screw x1, spring washer-8 x1, pendent tube washer x1, rubber washer-8 x1 and sponge x2. Compact Pendent Mount 184×104×115.2 mm (7.24×4.09×4.54 inches);...
- Page 25 Installation Guide Swan Tube For mounting with Swan Tube. White; Iron, Dimension: 835 x 300 mm (32.9×11.8 inches); Diameter: 45 mm (1.8 inches); Weight: 3.8 kg (8.4 lbs); Supplied with pendent tube washer x1, rubber washer-8 x1, waterproof rubber x1, spring washer-8 x1 and M8x12 screw x1. Corner Plate Mini For mounting with Compact Pendent Mount.
- Page 26 Installation Guide Pole Thin Direct Mounting 232(L)×136(W)×60(D) mm (9.1×5.4×2.4 inches); Diameter: 112~140 mm (4.4~5.5 inches); 0.7 kg (1.6 lbs). Supplied with stainless steel straps x4, M8x16 screw x4, washer x4 and spring washer-8 x4. Pole Wide Direct Mounting 270(L)×170(W)×60(D) mm (10.6×6.7×2.4 inches); Diameter: 112~130 mm (4.4~5 inches);...
- Page 27 Installation Guide Corner Wide Box Mounting 232(L)×234(W)×210(D) mm (9.1×9.2×8.3 inches); 2.7 kg (6 lbs); Supplied with M8x16 screw x4, washer-8 x4, and spring washer-8 x4. Power Box can be set inside the wide box. Pole Thin Box Mounting 291(L)×136(W)×242 (D) mm (11.5×5.4×9.5 inches); 3.1 kg (6.9 lbs); Supplied with M8x16 screw x4, washer-8 x4, spring washer x4 and stainless steel straps x4.
- Page 28 Installation Guide Wall Box Mounting 270(L)×166(W)×95(D) (10.6×6.5×3.7 inches); 2.2 kg (4.84 lbs); Supplied with M8x16 screw x4, washer-8 x4 and spring washer-8 x4. Power Box can be set inside the wall box. Stainless Steel Straps For fixing Pole Direct Mounting/ Pole Box on the pole. Length: 700 mm (27.5 inches);...
- Page 29 Installation Guide Other Application Accessories Repeater/Converter D77R1: RS-485/RS-232 Converter D77R2: RS-232 between RS-485/RS-442 D77R3: Bi-phase to RS-485/RS-422 D77R1 D77R2 D77R3 Power Box 186.5×147 mm (7.3×5.8 inches); 2.6 kg (5.8 lbs) P1030 (Input: 110~115VAC/Output: 24VAC 72VA) P2030 (Input: 220~230VAC/Output: 24VAC 72VA) Signal Distribution Unit Relay control codes to speed dome cameras.
-
Page 30: Ceiling Mounting With Straight Tube
Installation Guide Ceiling Mounting with Straight Tube The Straight Tube is available in different length: 25 cm and 30 cm. Package Contents: • M8x12 Screw x1 • Spring Washer-8 x1 • Pendant Tube Washer x1 • Rubber Washer-8 x1 • Waterproof Rubber x1 Items Needed: •... - Page 31 Installation Guide 6) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Straight Tube with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 7) Connect the cable(s) to the Dome Camera. 8) Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and washers.
-
Page 32: Wall Mount
Installation Guide Wall Mount 4.4.1 Swan Tube Package Contents: • M8x12 Screw x1 • Spring Washer-8 x1 • Pendent Tube Washer x1 • Rubber Washer-8 x1 • Waterproof Rubber x1 Items Needed: • Dome Camera • Swan Tube and other equipped items (optional accessory) •... -
Page 33: Compact Pendent Mount
Installation Guide Wall Mount: Swan Tube + Indoor Mounting Kit 4.4.2 Compact Pendent Mount Package Contents: • Rubber Washer-8 x1 • Pendant Tube Washer x1 • Spring Washer-8 x1 • M8x12 Screw x1 Items Needed: • Dome Camera • Outdoor Mount Kit (supplied) •... - Page 34 Installation Guide Tools Needed: • Tool for drilling • Tool for screwing Follow the steps below to mount the Dome Camera with the Compact Pendent Mount. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, users could push up the Cable Entry Board on the Compact Pendent Mount’s Mounting Plate to place the cables, as shown in the photo below.
-
Page 35: Standard Pendent Mount
Installation Guide 6) Connect the cable(s) to the Dome Camera. 7) Join the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw and washers. Wall Mounting: Compact Pendent Mount + Outdoor Mount Kit 4.4.3 Standard Pendent Mount Package Contents: •... - Page 36 Installation Guide Tools Needed: • Tool for drilling • Tool for screwing Follow the steps below to mount the Dome Camera with the Standard Pendent Mount. 1) Make a cable entry hole on the wall to recess the cables. Otherwise, users could push up the cable entry board on the Standard Pendent Mount’s mounting plate to place the cables (see the illustration in section 4.4.2 Compact Pendent Mount >...
-
Page 37: Wall Box Mounting
Installation Guide Wall Mounting: Standard Pendent Mount + Outdoor Mount Kit 4.4.4 Wall Box Mounting Package Contents: • M8x16 Screw x4 • Washer-8 x4 • Spring Washer-8 x4 Items Needed: • Dome Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) •... - Page 38 Installation Guide Follow the steps to mount the Dome Camera with the Standard/ Compact Pendent Mount and Wall Box Mounting. 1) Make a cable entry hole on the wall to recess the cable(s). 2) Fix the Wall Box Mounting on the wall with proper screws and screw anchors.
-
Page 39: Corner Mount
Installation Guide Corner Mount 4.5.1 Corner Standard Mounting Plate/Corner Plate Mini Package Contents: • Washer-8 x4 • Spring Washer-8 ×4 • M8x16 Screw x4 • M8 Nut x4 Items Needed: • Dome Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) •... - Page 40 Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. See the illustrations in section 4.4.2 Compact Pendent Mount > Step 4. 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers.
-
Page 41: Corner Thin/Wide Box Mounting
Installation Guide 4.5.2 Corner Thin/Wide Box Mounting Package Contents: • M8x16 Screw x4 • Washer-8 x4 • Spring Washer-8 x4 Items Needed: • Dome Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Ethernet Cable (network Dome Camera) •... - Page 42 Installation Guide 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera.
-
Page 43: Pole Mount
Installation Guide Pole Mount 4.6.1 Pole Thin/Wide Direct Mounting Package Contents: • Stainless Steel Straps x4 • M8x16 Screw x4 • Washer x4 • Spring Washer-8 x4 Items Needed: • Dome Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) •... - Page 44 Installation Guide NOTE: Please block the cable entry hole with the supplied sponge to avoid insects entering the Pendent Mount. See the illustrations in section 4.4.2 Compact Pendent Mount > Step 4. 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers.
-
Page 45: Pole Thin/Wide Box Mounting
Installation Guide 4.6.2 Pole Thin/Wide Box Mounting Package Contents: • M8x16 Screw x4 • Washer-8 x4 • Spring Washer x4, • Stainless Steel Straps x4 Items Needed: • Dome Camera • Outdoor Mount Kit (supplied) • Data Cable (supplied) • Ethernet Cable (network Dome Camera) •... - Page 46 Installation Guide 4) Attach the Waterproof Rubber to the Standard/ Compact Pendent Mount. 5) Thread the cable(s) through the Outdoor Mount Kit and join the Outdoor Mount Kit to the Standard/ Compact Pendent Mount with the supplied screws and washers. Then adjust the Waterproof Rubber to the joint. 6) Connect the cable(s) to the Dome Camera.
-
Page 47: System Expansion
Installation Guide System Expansion Connecting with Power Box A power box contains a 24V AC adapter, two terminal blocks (for communication and power) and one alarm board. With an IP66 case, the Power Box is ideal for outdoor installation environment. Two models are available: 100~115V AC power input (P1030) and 220~230V AC (P2030). -
Page 48: Data Formats Transforming
Installation Guide Data Formats Transforming To integrate other surveillance devices with the high speed dome cameras or to extend the distance of communications, users could employ three kinds of repeater/converter, as shown below. With the advanced circuit design, these repeaters/converters offer 1KVrms isolation voltage and surge protection capability. -
Page 49: Signal Distribution
Installation Guide Signal Distribution The RS-485 Signal Distribution Unit (SDU) is designed to relay control codes to speed dome cameras. It is capable of communicating with cameras up to 1.0 kilometers away. Additionally, the SDU can be installed in either “star” or “daisy chain”... -
Page 50: System Integration
Installation Guide System Integration The dome camera is allowed to be integrated into other suppliers' surveillance systems with large set of built-in protocols. Refer to the following sections for more information. Using Pelco Keyboard The speed dome camera can be controlled through a Pelco keyboard which built in with D protocol and P protocol. -
Page 51: Using Philips Allegiant Keyboard
Installation Guide Cable Definition (D Protocol Keyboard to PTZ Camera) Tx - Rx - For D Protocol Keyboard For SpeedDome Using Philips Allegiant Keyboard The dome cameras can be integrated into Philips Allegiant systems through D77R3 repeaters. Please follow the instructions to control dome cameras through Philips Allegiant systems. -
Page 52: Appendix A: Technical Specification
Auto / Manual AGC control Back Light On / Off Compensation OPERATION DynaColor, Pelco D&P, VCL, Philips, AD-422, JVC, Kalatel, etc Built-in Protocol English, French, German, Italian, Japanese, Polish, Portuguese, Multi-Language OSD Russian, Spanish, Turkish, Simplified Chinese, Traditional Chinese 360° endless Pan Travel -10°... - Page 53 Installation Guide Items G Model M Model V Model P Model T Model Cruise Privacy Mask On / Off (Pan and tilt speed proportional to zoom ratio) Proportional Pan & Tilt Resume after Power loss Zone Title Preset, Sequence, Auto pan, Cruise Home Function Digital / Mechanical / Off Auto Flip...
- Page 54 Auto / Manual AGC control On / Off Back Light Compensation OPERATION DynaColor, Pelco D&P, VCL, Philips, AD-422, JVC, Kalatel, etc. Built-in Protocol English, French, German, Italian, Japanese, Polish, Portuguese, Multi-Language OSD Russian, Spanish, Turkish, Simplified Chinese, Traditional Chinese 360° endless Pan Travel -10°...
- Page 55 Installation Guide Items S3 Model S4 Model S5 Model S6 Model Mechanical / Digital / Off Auto Flip On / Off Digital Slow Shutter On / Off Motion Detection On / Off Wide Dynamic Range Auto / Manual Day/Night: IR Cut Filter...
Need help?
Do you have a question about the S3 and is the answer not in the manual?
Questions and answers