AT&T SynJ SB67108 Quick Start Manual

Install and charge the handset battery
Step 1
Plug the battery connector securely into the
socket inside the handset battery compartment,
matching the color-coded label. Insert the
supplied battery with the label THIS SIDE UP
facing up, as indicated.
Step 2
Align the co�er flat against the battery
compartment, then slide it upwards.
Step 3
To lock the battery compartment, turn the latch
clockwise until it points to the lock icon , as
shown on the graphic.
Install and charge the handset battery
(continued)
Step 4
To charge the handset, place it in the charger.
The CHARGE light is on when the handset is
charging.
CHARGE
light
Add and register handsets
You can add up to ten SynJ SB67108 handsets
(sold separately) to the SynJ SB67138/SB67158,
but you must register each new handset with
the telephone base before use. Each handset is
assigned numbers in the order they are registered
(handsets 1 to 10).
To register a handset to your telephone base:
1. Make sure the handset is out of the charger
and the screen shows Press MENU on BS, sel
Registration & sel Register HS. Then put HS
in cradle before you begin registration.
2. On the telephone base, press MENU/ .
ENTER
3. Scroll down to Registration and press
ENTER.
MENU/
4. Press ENTER again to select
MENU/
Register HS. The telephone base screen shows
Registering new device...
5. Place the unregistered handset into the
charger. The handset beeps once and begins
registering to the telephone base. It takes up
to 60 seconds to complete the registration.
Add and register handsets (continued)
You hear a beep when the registration is
successful. The handset shows Handset
registered, and then shows X: Handset X
(X represents the extension number [1-0];
Handset X represents the handset name).
NOTE: If the registration is not successful, the screen shows
Press MENU on BS, sel Registration & sel Register HS.
Then put HS in cradle. To reset the handset, remo�e the set the handset, remo�e the
handset from the charger. Try the registration process again.
Mailbox setup
Each handset has its own mailbox that is different
from the general mailbox on the base. If you turn
on the auto attendant on the base, the caller can
lea�e a message on the handset mailbox after
two rings (Fast answer mode = On), or fi�e rings
(Fast answer mode = Off).
To turn Fast answer mode on or off:
1. Press the ress the M.box softkey.
2. Press DIR or CID to scroll to
Fast answer mode. Press /ENTER.
MENU
3. Press DIR or CID to select On or Off.
Press ENTER/
4. to sa�e the setting and
MENU
return to the pre�ious menu.
To record a new personal announcement:
1. Press the M.box softkey.
2. Press DIR or CID to scroll to
Anncemnt setup. Press /ENTER to play
MENU
current announcement.
3. Press the Press the Change softkey, and then press the
Start softkey. The system announces, "Record
after the tone. Press Stop when you are done."
4. Press the Stop softkey when finished. The
recorded announcement plays.
5. Press the OK softkey to use the new recorded
announcement.
-OR-
Press the Change softkey to record a new
announcement.
Message playback
You can play the messages from your handset
mailbox and the general mailbox. If you ha�e
new messages, the system plays them (in
chronological order) automatically when you
access the mailbox.
To listen to new messages on a cordless handset: listen to new messages on a cordless handset:
When the handset is idle, press the M.box softkey.
To listen to new messages on the general
mailbox:
1. When the handset is idle, press the
M.box softkey.
2. Press DIR or CID to scroll to
General mailbox.
3. Press /ENTER.
MENU
Quick start guide
SynJ SB67108
DECT 6.0 expansion handset
for use with AT&T model SynJ
SB67138/SB67158