Advertisement
ENGLISH
To obtain full benefit from the WA 41 A and
trouble
free
operation,
structions and information carefully.
DESCRIPTION AND FUNCTION
*
The control panel incorporates a
switch, a locking device for the fuel and a
pilot light.
*
The
electric
pump, which is positioned in the tank.
*
The fuel pump delivers fuel to the com-
bustion dish and is controlled by means of
the button above the control panel,
At position low, the consumption is approx.
2,5 l/h. At position high, the consumption
is approx. 4,3 l/h.
One and another depends on viscosity.
*
The main fan is controlled by a thermostat.
As soon as the combustion chamber has warmed
up sufficiently, the fan starts to operate.
*
The burner is equipped with an air intake
fan to supply air for combustion. This air
combustion
fan
extinguished.
connected to this fan so that the combustion
air can be sucked from outside the area to
be heated.
*
Most types of waste oil can be used, such as
gearbox oil, gas oil, diesel oil, hydraulic
oil, HBO 1, 2 and 3, but not those with a
high viscosity, such as SAE90.
DO
NOT
USE
TRANSFORMER
CONTAIN
SUBSTANCES
PERFORMANCE OF THE BURNER (PCB)
*
When the pump motor stops, the flame will
extinguish once the fuel in the burner dish
is exhausted.
WARNINGS
1
There
could
explosion if the burner is reignited while
it is still warm.
2
There must be sufficient air for combustion;
make sure that the combustion air intake fan
is never blocked.
3
Modifications made to the burner by dealer
or end user, invalidate the manufacturer's
warranty.
INSTALLATION
*
For
installation,
prescriptions.
*
The burner must be installed on a completely
level, concrete floor.
*
Check that the chose position presents no
problem for:
- electrical supply 230V/2Amp.;
- flue pipe installation;
- combustion air supply.
*
Open the top cover of the burner and remove
the cover of the combsution
chamber.
read
the
following
pump
motor
drives
the
stops
when
the
flame
φ
Pipes
200
mm
can
OIL
WHICH
DETRIMENTAL
TO
be
a
possible
danger
consult
the
* The
following
in-
combustion chamber:
1x
T-piece with built-in draught stabiliser
for flue pipe connection
1x
cleaning shovel
1x
scraping
combustion dish
1x
combustion dish
fuel
2x
burner ring
1x
spare card to seal the bottom of com-
bustion chamber
2x
handle with bolts
1x
pedal
FLUE PIPE
For
clean
and
essential that the flue pipe is installed correctly.
a.
minimum diameter of flue pipe: 150mm
b.
check that flue connections are well sea-
led
c.
minimum flue height: 5 m
d.
the wind must be able to reach the top of
has
the flue from all directions (e.g.: it may
be necessary to extend flue above roof
be
apex)
e.
all pipes should be vertical if possible,
keep
minimum
f.
avoid bends in the flue installation if
possible but if unavoidable e.g. if flue
has
through a wall or window, then:
MIGHT
1.
THE
2.
3.
of
local
-NLC-
items
are
packed
tool
to
remove
trouble
free
combustion,
horizontal
pipes
to
two
bends
because
of
the pipe should be as high as
possible within the building
flue
pipe
outside
should
be
insulated
walled)
the minimum height of the flue
has to be increased to 7.5 m to
compensate.
use a raincap
within
the
residue
from
it
is
the
absolute
installation
the
building
(double
Advertisement
