Polar Electro Look Keo Power User Manual

oFFSet caliBration training
The Polar LOOK Kéo Power system calibrates itself automatically Starting a training SeSSion
each time the transmitters wake up and a receiving Polar device
is found. Calibration takes a couple of seconds.
1. Wake up the transmitters and turn on the training wait
mode in your receiving device. Let the system calibrate.
Training temperature has an effect on the calibration
2. Start the training session with your receiving device to get
accuracy, so make sure your bike's temperature has become
stable before you start the offset calibration. information about power, cadence, efficiency and pedaling
balance.
1. Wake up the transmitters and turn on the training wait
For more instructions, see the user manual of your receiving
mode in your receiving Polar device to start the calibration.
device.
2. Keep the bike upright and cranks in place until calibration
is completed. Stopping a training SeSSion
3. Complete the calibration as guided by your receiving device.
After you've stopped the training session with your receiving
device, the transmitters go to sleep after 90 seconds of inactivity.
To ensure the calibration is done properly:
Force Vector MeaSureMent
» don't put any weight on the pedals during calibration.
» don't interrupt the calibration.
The Polar LOOK Kéo Power system comes with force vector
measurement. The feature enables the Polar training computer
If you're unsure whether the calibration succeeded or the
temperature changes by more than 10 °C / 18 °F, do it again to analyze your pedaling more precisely and helps you to learn
more efficient pedaling technique.
manually.
You can take the feature into use in the receiving device.
You can start the manual calibration with your receiving device
also during a training session.
You can find information on offset calibration with other than
Polar devices at www.polar.com/support.
iMportant inForMation
changing BatterieS technical SpeciFication
It's recommended that you change both transmitter batteries at Kéo Power Transmitters
the same time. Battery type CR2354
Battery life 5 months (2 h/day, 7 days/week)
Operating temperature -10 °C to +50 °C / 14 °F to 122 °F
changing tranSMitter Sealing ringS
Storage temperature -20 °C to +60 °C / -4 °F to 140 °F
Material Aluminium, PA+GF
Water resistance IPX7 (splash proof )
You received additonal sealing rings for the transmitters in the
product package.
LOOK Kéo Power Pedals
Operating temperature -10 °C to +50 °C / 14 °F to 122 °F
Remove the old sealing rings carefully with tweezers. Place the Storage temperature -20 °C to +60 °C / -4 °F to 140 °F
Distance crank/middle of the pedal 55 mm
new sealing rings into the grooves on the transmitters. Handle
Pedal float 0 (black cleats), 4.5 (grey cleats), or 9
the transmitter with extra care.
(red cleats) degrees
Water resistance IPX7 (splash proof )
Maintenance
Measurement ranges
Average power 0-2000 W
Before every ride, check the pedals and cleats to be sure they L/R balance 0-100%
are free of dirt and that they are operating properly. Check your Cadence 30-199 rpm
Maximum load 1800 N
cleats daily for excessive wear, and replace them if needed. Worn
cleats may come loose without noticing and cause you to crash.
Replace them only with genuine LOOK Kéo cleats. Do not drill,
paint or refinish them. Keep pedals and cleats away from any heat
source. Spindle: LOOK spindles are subjected to a rotation test of
two million cycles at 100 revs / minute, with a load of 90 kg on the
pedal and off centered rotation (which creates an impact at each
rev). This test exceeds the toughest known standard EN 14781.
High pressure cleaners are not recommended.
pedal tenSion adjuStMent 1.
LOOK pedals are always delivered preset to a minimum tension.
You can adjust them with a 3 mm Allen key at the rear of
the pedal on the lever. By turning the key in the + direction
(clockwise), you increase the amount of stress necessary for cleat
release. Allow tension to remain minimal until you've become
perfectly familiar with the system. Adjustment can't be carried
out when the cleat is engaged in the pedal. You will hear a "click"
when the maximum adjustment is reached. Once you hear the
click, stop screwing as it may damage the pedal.
engageMent / releaSe
Engagement: Insert the cleat in the pedal in accordance with
picture 1 and press down on the pedal to lock the cleat.
Release: Turn your heel outwards as in picture 2 and the cleat will 2.
disengage. Do not tilt your foot towards the bike, as the heel may
touch the spokes and cause a crash.
Find product support at Stay tuned with polar
www.polar.com/support/keo_power_sensor_
bluetooth_smart and at www.lookcycle.com.
facebook.com/ twitter.com/
polarglobal polarglobal
youtube.com/ instagram.com/
polar polarglobal
Stay tuned with looK cycle
LOOK Cycle velolook
Manufactured by
Polar Electro Oy LOOK Cycle International Lookcycletv
Professorintie 5 27, rue du Dr Léveillé
FI-90440 KEMPELE CS 90013
Tel +358 (0)8 5202 100 FR-58028 NEVERS Cedex
Fax +358 (0)8 5202 300 Tel +33 (0)3 86 71 63 00
www.polar.com Fax +33 (0)3 86 71 63 10
www.lookcycle.com
17952253.00 ENG 05/2014
Polar look kéo Power
User Manual
English