While Sewing - Baby Lock Destiny BLDY Instruction And Reference Manual

Problem
Pointer of the With thick elastic fabric, the position will be
embroidery foot "W+" misaligned only at raised parts in the fabric.
with LED pointer
With fabric having a very uneven surface, the
does not indicate the
position is not correctly aligned.
position correctly
Specifying with The sensor pen has not been calibrated.
sensor pen cannot be
done accurately.
The pen is being held differently than when it
was calibrated.

■ While sewing

Problem
Machine does not "Start/Stop" button was not pressed.
operate.
There is no pattern selected.
Presser foot is not lowered.
"Start/Stop" button was pressed with the foot
controller attached.
The "Start/Stop" button was pressed while the
machine is set for the sewing speed controller
to control the zigzag stitch width.
Needle breaks. Needle is installed incorrectly.
Needle clamp screw is not tightened.
Needle is turned or bent.
Using improper needle or thread for the
selected fabric.
Wrong presser foot was used.
Upper thread tension is too tight.
Fabric is pulled during sewing.
Spool cap is set incorrectly.
There are scratches around the opening in the
needle plate.
There are scratches around the opening in the
presser foot.
There are scratches on the bobbin case.
Needle is defective.
A bobbin designed specifically for this
machine is not used.
Upper threading is incorrect.
Bobbin is set incorrectly.
Presser foot is attached incorrectly.
Screw of the presser foot holder is loose.
Fabric is too thick.
Fabric is fed forcefully when sewing thick
fabric or thick seams.
Stitch length is too short.
Stabilizer is not attached to fabric being
embroidered.
Bobbin thread is incorrectly wound.
Cause
Manually adjust the position according to the
thickness of the fabric.
The pointer indication should be used only as
a reference.
Before using the sensor pen for the first time,
be sure to calibrate it.
When using the sensor pen, be sure to hold it
at the same angle as when it was calibrated.
The specification location may be misaligned if
the pen is held at a slightly different angle. In
this case, make fine adjustments after making
the selection.
Cause
Press the "Start/Stop" button.
Select a pattern.
Lower the presser foot.
Remove the foot controller, or use the foot
controller to operate the machine.
Use the foot controller instead of the "Start/
Stop" button to operate the machine, or set
the "Width Control" to "OFF" in the settings
screen.
Reinstall the needle correctly.
Tighten the needle clamp screw.
Replace the needle.
Check the "Fabric/thread/needle
combinations" chart.
Use the recommended presser foot.
Adjust the thread tension.
Do not pull the fabric during sewing.
Check the method for attaching the spool cap,
then reattach the spool cap.
Replace the needle plate, or consult your
authorized Baby Lock retailer.
Replace the presser foot, or consult your
authorized Baby Lock retailer.
Replace the bobbin case, or consult your
authorized Baby Lock retailer.
Replace the needle.
Incorrect bobbins will not work properly. Only
use a bobbin designed specifically for this
machine.
Check the steps for threading the machine and
rethread the machine.
Reset the bobbin thread correctly.
Attach the presser foot correctly.
Securely tighten the screw of the presser foot.
Use fabric that the needle can pierce when the
handwheel is turned.
Allow the fabric to be fed without being
forcefully pushed.
Adjust the stitch length.
Attach stabilizer.
Use a correctly wound bobbin.
TROUBLESHOOTING
Solution
Solution
111, 168, 200, 299
"STITCH SETTING
Page
250
—
50
50
Page
17
17
81
31, 81
73
74
73
75
CHART"
90, 287
—
60
9
117
68
376
73
57
60
57
68
69
85
85
89
173, 242
52
389