Husqvarna 327LS Series Operator's Manual
  1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 327LS
  6. Operator's manual

Husqvarna 327LS Series Operator's Manual

Hide thumbs Also See for 327LS Series:
Table of Contents

Advertisement

Quick Links

See also: Workshop Manual , Operator's Manual
Operator's manual
327LS 327LD
X-series
Please read the operator's manual carefully and make sure you understand the instructions
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 327LS Series

Summary of Contents for Husqvarna 327LS Series

  • Page 1 Operator’s manual 327LS 327LD X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols Only use non-metallic, flexible WARNING! Clearing saws, cutting attachments, i.e. trimmer brushcutters and trimmers can be heads with trimmer cord. dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual.

  • Page 3: Table Of Contents

    CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............2 Please read the operator’s manual carefully. CONTENTS Maintenance, replacement, or repair of the emission Contents ............... 3 control devices and system may be performed by any Note the following before starting: ......3 nonroad engine repair establishment or individual.

  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets.

  • Page 5: What Is What

    WHAT IS WHAT? What is what? Trimmer head 12 Cylinder cover Grease filler cap, bevel gear 13 Starter handle Bevel gear 14 Fuel tank Cutting attachment guard 15 Air filter cover Shaft 16 Air purge Shaft coupling (327LDx) 17 Choke control Loop handle 18 Handle adjustment Throttle control...

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can The only accessories you can operate with this engine cause serious or fatal injury to the operator or others.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS BOOTS control (B). When you release the handle the throttle control and the throttle lockout both move back to their Wear sturdy, non-slip boots. original positions. This movement is controlled by two independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting.
  • Page 8 GENERAL SAFETY PRECAUTIONS be checked. See instructions under the heading Vibration damping system Maintenance. Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Stop switch Use the stop switch to switch off the engine. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS In countries that have a warm and dry climate there is a WARNING! Bear in mind that: significant risk of fire. We therefore fit certain mufflers with a spark arrestor screen. Check whether the muffler on your machine is fitted with this kind of screen. The exhaust fumes from the engine are hot and may contain sparks which can start a fire.

  • Page 10: Trimmer Head

    GENERAL SAFETY PRECAUTIONS Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size.

  • Page 11: Assembly

    ASSEMBLY Fitting the loop handle • Before using the unit, tighten the knob securely. • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Dismantling: • Loosen the coupling by turning the knob (at least 3 times).

  • Page 12: Assembling The Cutting Equipment

    ASSEMBLY Assembling the cutting • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. equipment WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of •...

  • Page 13: Fuel Handling

    Two-stroke oil long-term storage, if the machine is not under close supervision and when performing all service • For best results and performance use HUSQVARNA measures. two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. WARNING! Take care when handling fuel.

  • Page 14: Fueling

    FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.

  • Page 15: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping • Check that the support flange is not cracked due to WARNING! The complete clutch cover fatigue or due to being tightened too much. Discard and shaft must be fitted before the the support flange if it is cracked.
  • Page 16 STARTING AND STOPPING apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.

  • Page 17: Working Techniques

    WORKING TECHNIQUES General working instructions Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.

  • Page 18: Basic Working Techniques

    WORKING TECHNIQUES Basic working techniques Cutting • The trimmer is ideal for cutting grass that is difficult to Always slow the engine to idle speed after each working reach using a normal lawn mower. Keep the cord operation. Long periods at full throttle without any load on parallel to the ground when cutting.

  • Page 19: Maintenance

    MAINTENANCE Carburetor cause fire if directed against dry and combustible material. Adjustment of the idle speed Before any adjustments are made, make sure that the air filter is clean and the air filter cover is fitted. Adjust the idle speed using the idle adjustment screw T, if it is necessary to readjust.

  • Page 20: Cooling System

    MAINTENANCE Cooling system If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.020 inch (0.5 mm).

  • Page 21: Bevel Gear

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 22: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily Weekly Monthly Maintenance maintenance maintenance maintenance Clean the outside of the machine. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.

  • Page 23: Technical Data

    TECHNICAL DATA Technical data 327LDx 327LS Motor Cylinder displacement, cu.in/cm 1,50/24,5 1,50/24,5 Cylinder bore, inch/mm 1,34/34 1,34/34 Stroke, inch/mm 1,06/27 1,06/27 Idle speed, rpm 2700 2700 Recommended max. speed, rpm 11000-11700 11000-11700 Speed of output shaft, rpm 8300 8300 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/8400 0,9/8400 Catalytic converter muffler...
  • Page 24 537 42 54-01 The accessories have been developed mainly for the Husqvarna 125LD trimmer, but can also be used in combination with the specified power heads and have been evaluated to applicable ISO- and EN safety requirement standards by the Swedish Machinery Testing Institute.

  • Page 25: Federal And California Emissions Control Warranty Statement

    If the part fails prior to the first scheduled replacement, engine is defective, the part will be repaired or replaced the part will be repaired or replaced by Husqvarna Forest by Husqvarna Forest & Garden. & Garden at no cost. Any such part repaired or replaced under warranty is warranted for the remainder of the OWNER′S WARRANTY...

  • Page 26: Your Warranty Rights And Obligations

    EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
  • Page 28 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 29 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 30 T35, T35x 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...
  • Page 31 6,0 m 10 cm 4" 3,05 m "Clic" 15 cm 6"...
  • Page 36 Original instructions 1155663-95 ´®z+WbG¶5,¨ ´®z+WbG¶5,¨ 2014-12-02...

This manual is also suitable for:

327ldx series327rjx series

Table of Contents