1. Manuals
  2. Brands
  3. Husqvarna Manuals
  4. Trimmer
  5. 327LDX Series
  6. Operator's manual

Husqvarna 327LDX series Operator's Manual

Owners manual
Hide thumbs Also See for 327LDX series:
Table of Contents

Advertisement

Quick Links

See also: Workshop Manual
Operator's manual
327LS 327LD
X-series
Please read the operator's manual carefully and make sure you understand the instructions
before using the machine.
E E E E n n n n g g g g l l l l i i i i s s s s h h h h

Advertisement

Table of Contents
loading

Related Manuals for Husqvarna 327LDX series

Summary of Contents for Husqvarna 327LDX series

  • Page 1 Operator’s manual 327LS 327LD X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...

  • Page 2: Key To Symbols

    KEY TO SYMBOLS Symbols Only use non-metallic, flexible WARNING! Clearing saws, cutting attachments, i.e. trimmer brushcutters and trimmers can be heads with trimmer cord. dangerous! Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the Other symbols/decals on the machine refer to...

  • Page 3: Table Of Contents

    Carburetor ............19 Muffler ..............19 Cooling system ............. 20 Spark plug ............20 Two-piece shaft (327LDx) ........21 Air filter ..............21 The Emissions Compliance Period referred to on the Maintenance schedule ......... 23 Emission Compliance label indicates the number of...

  • Page 4: Introduction

    Dear customer! Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689, when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production of muskets.

  • Page 5: What Is What

    13 Starter handle Bevel gear 14 Fuel tank Cutting attachment guard 15 Air filter cover Shaft 16 Air purge Shaft coupling (327LDx) 17 Choke control Loop handle 18 Handle adjustment Throttle control 19 Drive disc Stop switch 20 Operator’s manual...

  • Page 6: General Safety Precautions

    GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! The machine is only designed for trimming grass. A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can The only accessories you can operate with this engine cause serious or fatal injury to the operator or others.

  • Page 7: Machine's Safety Equipment

    GENERAL SAFETY PRECAUTIONS BOOTS control (B). When you release the handle the throttle control and the throttle lockout both move back to their Wear sturdy, non-slip boots. original positions. This movement is controlled by two independent return springs. This arrangement means that the throttle control is automatically locked at the idle setting.
  • Page 8 GENERAL SAFETY PRECAUTIONS be checked. See instructions under the heading Vibration damping system Maintenance. Your machine is equipped with a vibration damping system that is designed to reduce vibration and make operation easier. Stop switch Use the stop switch to switch off the engine. Use of incorrectly wound cord or an incorrect cutting attachment increases the level of vibration.

  • Page 9: Cutting Equipment

    GENERAL SAFETY PRECAUTIONS In countries that have a warm and dry climate there is a WARNING! Bear in mind that: significant risk of fire. We therefore fit certain mufflers with a spark arrestor screen. Check whether the muffler on your machine is fitted with this kind of screen. The exhaust fumes from the engine are hot and may contain sparks which can start a fire.
  • Page 10 GENERAL SAFETY PRECAUTIONS Trimmer head IMPORTANT! Always ensure the trimmer cord is wound tightly and evenly around the drum, otherwise the machine will generate harmful vibration. • Only use the recommended trimmer heads and trimmer cords. These have been tested by the manufacturer to suit a particular engine size.

  • Page 11: Assembly

    • Now adjust the trimmer to give a comfortable working coupling. position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft (327LDx) Assembly: • Loosen the coupling by turning the knob. • Align the tab of the attachment (A) with the arrow on the coupling (B).

  • Page 12: Assembling The Cutting Equipment

    ASSEMBLY Assembling the cutting • Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. equipment WARNING! When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of •...

  • Page 13: Fuel Handling

    Two-stroke oil long-term storage, if the machine is not under close supervision and when performing all service • For best results and performance use HUSQVARNA measures. two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. WARNING! Take care when handling fuel.

  • Page 14: Fueling

    FUEL HANDLING Mixing Fueling • Always mix the gasoline and oil in a clean container intended for fuel. • Always start by filling half the amount of the gasoline to be used. Then add the entire amount of oil. Mix (shake) the fuel mixture.

  • Page 15: Starting And Stopping

    STARTING AND STOPPING Check before starting Starting and stopping • Check that the support flange is not cracked due to WARNING! The complete clutch cover fatigue or due to being tightened too much. Discard and shaft must be fitted before the the support flange if it is cracked.
  • Page 16 STARTING AND STOPPING apply full throttle; the throttle will automatically disengage from the start setting. CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended.

  • Page 17: Working Techniques

    WORKING TECHNIQUES General working instructions Always hold the machine with both hands. Hold the machine on the right side of your body. IMPORTANT! This section takes up the basic safety precautions for working with a trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert.

  • Page 18: Basic Working Techniques

    WORKING TECHNIQUES Basic working techniques Cutting • The trimmer is ideal for cutting grass that is difficult to Always slow the engine to idle speed after each working reach using a normal lawn mower. Keep the cord operation. Long periods at full throttle without any load on parallel to the ground when cutting.

  • Page 19: Maintenance

    Basic setting • The basic carburetor settings are adjusted during Your Husqvarna product has been designed and testing at the factory. The basic setting is richer than manufactured to specifications that reduce harmful the optimal setting and should be maintained for the emissions.

  • Page 20: Cooling System

    MAINTENANCE cause fire if directed against dry and combustible Cooling system material. To keep the working temperature as low as possible the machine is equipped with a cooling system. Some mufflers are equipped with a special spark arrestor screen. If your machine has this type of muffler, you should clean the screen at least once a week.

  • Page 21: Two-Piece Shaft (327Ldx)

    See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact.

  • Page 22: Bevel Gear

    However, before using the machine you should check that the bevel gear is filled three-quarters full with grease. Use HUSQVARNA special grease. The grease in the bevel gear does not normally need to be changed except if repairs are carried out.

  • Page 23: Maintenance Schedule

    MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. Daily Weekly Monthly Maintenance maintenance maintenance maintenance Clean the outside of the machine. Make sure the throttle trigger lock and the throttle function correctly from a safety point of view.

  • Page 24: Technical Data

    TECHNICAL DATA Technical data 327LDx 327LS Motor Cylinder displacement, cu.in/cm 1,50/24,5 1,50/24,5 Cylinder bore, inch/mm 1,34/34 1,34/34 Stroke, inch/mm 1,06/27 1,06/27 Idle speed, rpm 2700 2700 Recommended max. speed, rpm 11000-11700 11000-11700 Speed of output shaft, rpm 8300 8300 Max. engine output, acc. to ISO 8893, kW/ rpm...
  • Page 25 537 42 54-01 The accessories have been developed mainly for the Husqvarna 125LD trimmer, but can also be used in combination with the specified power heads and have been evaluated to applicable ISO- and EN safety requirement standards by the Swedish Machinery Testing Institute.

  • Page 26: Federal And California Emissions Control Warranty Statement

    If the part fails prior to the first scheduled replacement, Husqvarna Forest & Garden. the part will be repaired or replaced by Husqvarna Forest & Garden at no cost. Any such part repaired or replaced OWNER′S WARRANTY...

  • Page 27: Emission Warranty Parts List

    EPA may not be used. The use of any non-exempted add-on or modified parts will be grounds for disallowing a warranty claim. Husqvarna Forest & Garden will not be liable to warrant failures of warranted parts caused by the use of a non-exempted add-on or modified part.
  • Page 29 8,5 m 10 cm 4" 4,2 m "Clic" 15 cm 6"...
  • Page 30 4,25 m 4,25 m 15 cm 6" 15 cm 6"...
  • Page 31 T35, T35x 8,5 m 10 cm 4" 4,3 m "Clic" 15 cm 6"...
  • Page 32 6,0 m 10 cm 4" 3,05 m "Clic" 15 cm 6"...
  • Page 36 Original instructions 1153293-95 ´®z+U=G¶59¨ ´®z+U=G¶59¨ 2010-03-03...

This manual is also suitable for:

327ls

Table of Contents