Husqvarna 327HDA65 X-series Operator's Manual
Hedge trimmer
Hide thumbs
Also See for 327HDA65 X-series:
- Operator's manual (28 pages) ,
- Operator's manual (28 pages)
Table of Contents
Related Manuals for Husqvarna 327HDA65 X-series
Summary of Contents for Husqvarna 327HDA65 X-series
- Page 1 Operator′s manual 327HDA65 X-series 327HE3 327HE4 X-series X-series Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
KEY TO SYMBOLS Symbols Keep all parts of your body away from hot surfaces. WARNING! Incorrect or careless use of a hedge trimmer can turn it into a dangerous tool that can cause serious or even fatal injury. It is extremely important that you Always wear approved protective read and understand the contents gloves. -
Page 3: Table Of Contents
CONTENTS Contents Note the following before starting: KEY TO SYMBOLS Symbols ..............2 Please read the operator’s manual carefully. CONTENTS Contents ............... 3 WARNING! Long-term exposure to noise can result in permanent hearing Note the following before starting: ......3 impairment. -
Page 4: Introduction
The business concept is to develop, manufacture and market motor driven products for forestry and gardening as well as for building and construction industry. Husqvarna ′ s aim is also to be in the front edge according to ergonomics, usability, security and environmental protection. -
Page 5: What Is What
WHAT IS WHAT? 327HE4 327HDA65 What is what? Cutter 16 Air purge Grease nipple and plug for filling lubricant. 17 Air filter cover Bevel gear 18 Clutch cover Blade guard (327HDA65) 19 Hand guard mounting screw (327HDA65, 327HE3) Shaft 20 Angle adjustment handle (327HE3, 327HE4) Front handle (327HDA65, 327HE3) 21 Angle adjustment knob Front handle (327HE4) -
Page 6: General Safety Precautions
GENERAL SAFETY PRECAUTIONS Important Personal protective equipment IMPORTANT! IMPORTANT! Incorrect or careless use of a hedge trimmer can turn it The machine is only designed for cutting branches and into a dangerous tool that can cause serious or even fatal twigs. -
Page 7: Machine's Safety Equipment
GENERAL SAFETY PRECAUTIONS FIRST AID KIT Make sure the throttle control is locked at the idle setting when the throttle lockout is released. Always have a first aid kit nearby. Machine′s safety equipment This section describes the machine′s safety equipment, its purpose, and how checks and maintenance should be carried out to ensure that it operates correctly. - Page 8 GENERAL SAFETY PRECAUTIONS Stop switch The machine′s vibration damping system reduces the transfer of vibration between the engine unit/cutting Use the stop switch to switch off the engine. equipment and the machine′s handle unit. Regularly check the vibration damping units for cracks or deformation.
- Page 9 GENERAL SAFETY PRECAUTIONS Never use a machine that has a faulty muffler. using the locking nut on the top of the bar. Check that the screws are loose enough to allow the washers under the screw heads to slide sideways. Regularly check that the muffler is securely attached to the machine.
-
Page 10: Assembly
ASSEMBLY Fitting the hand guard and loop Fitting the cutting head handle (327HDA65) (327HDA65, 327HE3) It is important that the hedge trimmer is laid on a flat surface when you fit the cutting head. Otherwise the Slide the spacer into the slot in the loop handle. cutting head may not be fitted straight. -
Page 11: Fitting The Impact Guard
ASSEMBLY Fitting the impact guard (327HE4) Fit the guard using the three screws and washers. Fit the two short screws in hole A. Tighten the screws to a torque of 4 Nm. After the machine has been in use for around 20 hours, re-tighten the screws to 4 Nm. -
Page 12: Fuel Handling
Ensure the machine is cleaned and that a complete Two-stroke oil service is carried out before long-term storage. • For best results and performance use HUSQVARNA • The transport guard must always be fitted to the two-stroke engine oil, which is specially formulated for cutting attachment when the machine is being our air-cooled two-stroke engines. -
Page 13: Fuelling
FUEL HANDLING Mixing Fuelling • Always mix the petrol and oil in a clean container intended for fuel. • Always start by filling half the amount of the petrol to be used. Then add the entire amount of oil. Mix WARNING! Taking the following (shake) the fuel mixture. -
Page 14: Starting And Stopping
STARTING AND STOPPING Check before starting Starting and stopping • Inspect the working area. Remove any objects that WARNING! The complete clutch cover could be thrown out. and shaft must be fitted before the • Check the cutting attachment. Never use blades that machine is started, otherwise the clutch are dull, cracked or damaged. - Page 15 STARTING AND STOPPING CAUTION! Do not pull the starter cord all the way out and do not let go of the starter handle when the cord is fully extended. This can damage the machine. CAUTION! Do not put any part of your body in marked area.
-
Page 16: Working Techniques
WORKING TECHNIQUES General working instructions • Keep in mind that the operator is responsible for accidents or hazards occuring to other people or their property. IMPORTANT! Safety instructions while working This section takes up the basic safety precautions for working with a hedge trimmer. If you encounter a situation where you are uncertain how to proceed you should ask an expert. -
Page 17: Basic Working Techniques
WORKING TECHNIQUES • Never put the machine down with the engine running • Hold the machine as close to your body as possible to unless you have it in clear sight. get the best balance. Safety instructions after completing work •... -
Page 18: Transport Position
WORKING TECHNIQUES (327HDA65) Loosen the knob on the shaft (clockwise). • Undo the knob. Grip the handle on the cutting unit and angle the cutting unit upwards. At an angle of 90 degrees there is a stop position. To pass the stop position, pull out the lock button. -
Page 19: Maintenance
Carburettor the optimal setting and should be maintained for the first few hours the machine is in use. The carburettor Your Husqvarna product has been designed and should then be finely adjusted. Fine adjustment manufactured to specifications that reduce harmful should be carried out by a skilled technician. -
Page 20: Cooling System
MAINTENANCE cause fire if directed against dry and combustible Cooling system material. To keep the working temperature as low as possible the machine is equipped with a cooling system. Some mufflers are equipped with a special spark arrestor mesh. If your machine has this type of muffler, you should clean the mesh at least once a week. -
Page 21: Air Filter
See instructions under the heading Oiling the air filter. Oiling the air filter Always use HUSQVARNA filter oil, art. no. 531 00 92-48. The filter oil contains a solvent to make it spread evenly through the filter. You should therefore avoid skin contact. -
Page 22: Cleaning And Lubrication
MAINTENANCE Cleaning and lubrication Clean any resin and plant residue from the blades using cleaning agent 531 00 75-13 (UL22) before and after using the machine. Lubricate the blade bars with special grease, part no. 531 00 75-12 (UL 21) before long periods of storage. 22 –... -
Page 23: Maintenance Schedule
MAINTENANCE Maintenance schedule The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the Maintenance section. The user must only carry out the maintenance and service work described in this Operator’s Manual. -
Page 24: Technical Data
TECHNICAL DATA Technical data 327HDA65 327HE3 327HE4 Engine Cylinder displacement, cm 25,4 25,4 25,4 Cylinder bore, mm Stroke, mm Idle speed, rpm 2700 2700 2700 Recommended max. speed, rpm 11000-12600 11000-12600 11000-12600 Max. engine output, acc. to ISO 8893, kW/ rpm 0,9/8400 0,9/8400 0,9/8400... -
Page 25: Ec-Declaration Of Conformity
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declare under sole responsibility that the hedge trimmers Husqvarna 327HDA65 from 2009’s serial numbers and onwards (the year is clearly stated in plain text on the type plate with subsequent serial number), are in conformity with the standards or or other normative documents following the provisions in the COUNCIL’S DIRECTIVES:... - Page 28 Original instructions 1153296-26 ´®z+U=^¶6d¨ ´®z+U=^¶6d¨ 2010-08-27...