Other Function; Display Mode; Recording An Analog Source; Selecting Analog Audio Input Or Digital Audio - Marantz SR7002 User Manual

OTHER FUNCTION

DISPLAY MODE

AV SURROUND RECEIVER SR8002
LIP.SYNC
PREV
GUIDE
PURE DIRECT SURROUND
DISP MULTI AUTO TUNED ST SPKR A B V-OFF PEAK ATT ANALOG MENU
DIGITAL DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 NIGHT EQ
L C R
AAC PCM LFE
SL S SR TEST CH.SEL
DSD
1
7.1CH ATT
SURROUND MULTI
MODE AUTO MULTI SPEAKER BAND T-MODE MEMORY
4
7.1CH INPUT DISPLAY
DISP DISP OSD
S
PURE DIRECT THX M-DAX
7 7
ENTER
MENU EXIT
PHONES
MIC
THX
CLEAR
You can select the display mode for the front display
of the unit.
To select this mode, press the DISPLAY on the
remote controller or the front panel.
When this button is pressed, the display mode is
switched in the following sequence.
Input Mode → Surround Mode → Auto display OFF
→ Display OFF → Normal Mode → Input Mode
Normal Mode:
Displays the selected input function. If the function
has been renamed using the Function Rename
feature (see page 44), the renamed name appears
on the display.
Input Mode:
Displays the input mode set via the Function Input
Setup feature (see page 43).
Surround Mode:
Displays the status of the selected surround
mode.
Auto Display Off mode:
The display is off. But, if you make a change to
the unit such as the input or surround mode, the
display will show that change, then go back to off
after about 3 seconds. When changing the volume,
it is not displayed.
Display Off mode:
The display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition.
64

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source
selected for listening through this unit is sent to the
record outputs.
This means that any program you are watching
or listening to may be recorded simply by placing
MUTE
machines connected to the outputs for TAPE OUT,
EXIT
CD/CDR OUT, VCR1 OUT, and DSS/VCR2 OUT in
SURR
2 3
the record mode.
SPK-AB
5 6
SLEEP
8 9
To record the input source signal you are currently
0
MEMO
watching or listening to
1.
AV SURROUND RECEIVER SR8002
INPUT SELECTOR
PURE DIRECT DISP MULTI AUTO TUNED
SLEEP AUTO SURR DIRECT
DSD
SURROUND MULTI
MODE AUTO MULTI SPEAKE
1.
7.1CH INPUT
PURE DIRECT THX
STANDBY
MENU
POWER ON/OFF PHONES
1.
Select the input source to record by turning the
INPUT FUNCTION SELECTOR knob on the
front panel or simply press the input selector
buttons on the remote controller.
The input source is now selected and you may
watch or listen to it as desired.
2.
The currently selected input source signal
is output to the TAPE OUT, CD/CDR OUT,
VCR1 OUT, and DSS/VCR2 OUT outputs for
recording.
3.
Start recording to the recording component as
desired.
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
USE PAGE
CH
TUNER CD
TAPE AUX1
1
Learning Remote Controller
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for each
input source as following procedures.
TV TV DVD DVD VCR VCR DSS DSS
Press the AMP button and press the > button until
TUNER TUNER CD CD CD-R CD-R MD MD
PAGE4 is displayed. Press the A/D (D3) button.
TAPE TAPE AUX1 AUX1 AUX2 AUX2 AMP
When this button is pressed, the input mode is
LIGHT
1 2
switched in the following sequence.
RC8001SR
Learning Remote Controller
Auto → HDMI → Digital → Analog → Auto
Auto mode:
The types of signals being input to the digital and
analog input jacks for the selected input source are
detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
HDMI mode:
HDMI mode can be selected only when an HDMI
input has been assigned as an input source.
When "HDMI AUDIO" under PREFERENCE of the
SETUP MENU is set to "THROUGH", the HDMI
mode cannot be selected.
Digital mode:
The input signal is fi xed to an assigned digital input
terminal.
Analog mode:
The analog input jacks are selected.
This selection is temporary and will not be stored in
memory.
To store changes to the input mode, select "1. INPUT
SETUP" from the MAIN MENU. (See page 43)

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the unit's output
through a pair of headphones. Be certain that the
M
headphones have a standard 1/4" stereo phono
D1
plug.
D2
Note that the speakers will automatically be turned
D3 D3
off when the headphone jack is in use.
D4
4
D5 D5
VOL
CD-R MD
AUX2 AMP AMP
LIGHT
2
RC8001SR
Note:
• When using headphones, the surround mode will
change to STEREO and Dolby Headphone by
MENU and Cursor button.
• The surround mode returns to the previous setting
as soon as the headphone plug is removed from the
jack.
AV SURROUND RECEIVER SR8002
INPUT SELECTOR
PURE DIRECT DISP MULTI AUTO TUNED ST SP
SLEEP AUTO SURR DIRECT DISC 6.1
DSD
SURROUND MULTI
MODE AUTO MULTI SPEAKER
7.1CH INPUT
PURE DIRECT THX
STANDBY
MENU
POWER ON/OFF PHONES