Table of Contents
Advertisement
OTHER FUNCTION
The remote control operations in this chapter are
performed with the remote control unit set to the
Amp mode. To set the Amp mode, tap the A/V
Amp on the Home screen on the remote control
unit.
VIDEO AUTO ON/OFF FUNCTION
This function allows the component connected to
the VIDEO input jack to control the power (ON/
OFF) to the SR9600.
The Auto Power On/Off mode is explained using a
connected DVD player as an example.
AUTO POWER ON
1.
Connect a DVD player to the DVD VIDEO, S-
VIDEO or COMPONENT VIDEO input jack.
2.
Be sure the Video on mode in the SETUP
MENU is set to "ENABLED". (See page 43 : 4.
VIDEO SETUP) Turn on the DVD player.
4 . V I D E O
S E T U P
V I D E O
A U T O
O N
V I D E O
C O L O R
B A R
V I D E O
C O N V E R T
: E N A B L E
A U T O
V I D E O
S E L : D I S A B L E
O S D
I N F O
: E N A B L E
R E T U R N
3.
Turn off the power to the DVD player and the
SR9600.
4.
Turn on the DVD player.
5.
The SR9600 turns on and DVD player is
selected automatically.
AUTO POWER OFF
1.
Turn the DVD player off.
2.
The power to the SR9600 switches to standby
after approx. 5 minutes.
Notes:
• The Auto Power Off mode is canceled if the
SR9600 is set to a source other than DVD.
• Some progressive video signals cannot be
detected when input to the COMPONENT
VIDEO input jacks.
SR9600U DFU̲01̲ENG 4̲4
Page 55
All manuals and user guides at all-guides.com
AUTO VIDEO SELECTOR
(AUTO VIDEO SEL)
Function can be changed according to the
detected video signal.
1.
Be sure the AUTO VIDEO SEL mode in the
SETUP MENU is set to "ENABLED". (See
page 43 : 4. VIDEO SETUP)
4 . V I D E O
V I D E O
A U T O
V I D E O
C O L O R
V I D E O
C O N V E R T
A U T O
V I D E O
S E L : D I S A B L E
O S D
I N F O
R E T U R N
2.
Turn on the power, for example, to the DVD
player.
3.
The DVD Function is automatically selected.
Notes:
• If a separate video signal (e.g., DSS, etc.) is input
after another component has been automatically
selected, the receiver switches to the DSS mode.
Then, when that DSS signal ceases, the receiver
searches for a component that is inputting a video
signal and switches to it.
• This feature works with the VIDEO, S-VIDEO
and COMPONENT VIDEO input jacks.
E X I T
• Some progressive video signals cannot be
detected when input to the COMPONENT
VIDEO input jacks.
ATTENUATION TO ANALOG INPUT
SIGNAL
If the selected analog audio input signal is greater
than the capable level of internal processing, the
"PEAK" indicator will light up on the front display.
1.
If this happens, you should tap the ATT on the
remote control unit.
The "ATT" indicator is illuminated when this
S E T U P
function is activated. The signal input level is
O N
reduced by about half.
B A R
: E N A B L E
wed Jun 01
5/8
: E N A B L E
E X I T
2.
To turn the attenuation feature off, tap the
ATT on the remote control unit again.
Notes:
• Attenuation will not work with the output signal
from TAPE OUT, CD-R/MD OUT, VCR1 OUT
and VCR2/DVD-R OUT.
• This function is memorized for each individual
input source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR9600's
output through a pair of headphones. Be certain that
the headphones have a standard 1/4" stereo phono
plug. (Note that the speakers will automatically be
turned off when the headphone jack is in use.)
Note:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
DOLBY HEADPHONE MODE
This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD menu system that appears when the
MENU button is pressed is shown below.
4:40
pm
A/V Amp
Mode
1.
Select the desired DOLDBY HP (Headphone)
mode with the
BYPASS → DH1 → DH2 → DH3 → BYPASS
BYPASS : Bypasses the Dolby headphone mode
DH1: The size of a typical living room space
DH2: The expansiveness of a structure as
DH3: A large space such as that found in a
When the Pure Direct or Source Direct mode is
selected, Dolby surround processing is bypassed
and "✽✽✽" is displayed as the mode indication.
Surround mode can be selected when DH1, DH2
or DH3 is selected.
The L/R level can be set in the ±10 dB range.
Notes:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
• The TONE cannot be set when DH1, DH2 or DH3
AV SURROUND RECEIVER SR9600
AV SURROUND RECEIVER SR9600
is selected.
INPUT SELECTOR
INPUT SELECTOR
• The Dolby Headphone mode will not work when
96/192 kHz PCM digital signals are input.
PURE DIRECT
PURE DIRECT
THX
THX
DOWN
DOWN
TUNING
UP
BAND
F/P
SURROUND
SURROUND
MULTI
MULTI
MODE
MODE
AUTO
AUTO
MULTI
MULTI
SPEAKER
SPEAKER
AUTO TUNE
T-MODE
MEMORY
CLEAR
7.1CH INPUT
7.1CH INPUT
DISPLAY
SPEAKERS
PURE DIRECT
PURE DIRECT
THX
THX
MRAC
A/B
STANDBY
STANDBY
ENTER
MENU
MENU
EXIT
POWER ON/STANDBY
POWER ON/STANDBY
PHONES
PHONES
MIC
05.4.27, 5:47 PM
Adobe PageMaker 6.5J/PPC
HEAD PHONE
DOLBY HP MODE
: BYPASS
: ✽✽✽
SURROUND
L LEVEL
: 0dB
R LEVEL
: 0dB
or
cursor buttons.
and delivers ordinary 2 channel stereo.
is simulated.
large as a music hall is simulated.
movie theater is simulated.
VOLUME
DOWN
UP
AUX 1 INPUT
DIGITAL
S-VIDEO
VIDEO
L
AUDIO
R
55
Advertisement
Table of Contents
