Page 1
Service SR7009 / U1B/N1B/N1SG/K1B/FN Manual AV Surround Receiver • For purposes of improvement, specifications and design are subject to change without notice. • Please use this service manual with referring to the operating instructions without fail. • Some illustrations using in this service manual are slightly different from the actual set. Ver.
CONTENTS ABOUT THIS MANUAL .............3 Audio Check PASS ..............121 What you can do with this manual ..........3 CLOCK FLOW & WAVE FORM IN DIGITAL BLOCK ...122 Using Adobe Reader (Windows version) ........4 LEVEL DIAGRAM ..............123 SAFETY PRECAUTIONS ............6 POWER DIAGRAM ..............130 NOTE FOR SCHEMATIC DIAGRAM .........7 WIRING DIAGRAM for CX870 ..........131 NOTE FOR PARTS LIST ............7...
ABOUT THIS MANUAL Read the following information before using the service manual. What you can do with this manual Search for a Ref. No. (phrase) Jump to the target of a schematic diagram connector (Ctrl+Shift+F) You can use the search function in Acrobat Reader to search for a Ref.
SAFETY PRECAUTIONS The following items should be checked for continued protection of the customer and the service technician. leakage current check Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassis resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective.
NOTE FOR SCHEMATIC DIAGRAM WARNING: Partsindicatedbythe z markhavecriticalcharacteristics.UseONLYreplacementpartsrecommendedbythemanufacturer. CAUTION: Beforereturningthesettothecustomer,besuretocarryouteither(1)aleakagecurrentcheckor(2)alinetochassisresistancecheck.If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the set is defective. WARNING: DONOTreturnthesettothecustomerunlesstheproblemisidentifiedandremedied. NOTICE: ALLRESISTANCEVALUESINOHM.k=1,000OHM/M=1,000,000OHM ALLCAPACITANCEVALUESAREEXPRESSEDINMICROFARAD,UNLESSOTHERWISEINDICATED.PINDICATESMICRO-MICRO...
Service Jig When you repair the printing board, you can use the following JIG (Extension cable kit). Please order it from Marantz Official Service Distributor in your region if necessary. 8U- 110084S : EXTENSION UNIT KIT : 1 Set 8U- 110136S : EXTENSION UNIT KIT : 1 Set (Refer to page.)
DISASSEMBLY • Remove each part in the order of the arrows below. • Reassemble removed parts in the reverse order. Read "Precautions During Work" before reassembling removed parts. • • I f wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing the work. Failure to shape the wires correctly may cause problems such as noise. TOP COVER FRONT PANEL ASSY DIGITAL PCB ASSY See "DISASSEMBLY" See "DISASSEMBLY" 1. FRONT PANEL ASSY 3. DIGITAL PCB ASSY and "EXPLODED VIEW" and "EXPLODED VIEW" FRONT PCB DIGITAL PCB (Ref. No. of EXPLODED VIEW : C5) (Ref. No. of EXPLODED VIEW : C49) HEAD PHONE PCB GUIDE PCB (Ref. No. of EXPLODED VIEW : C2) (Ref. No. of EXPLODED VIEW : C48) FRONT HDMI PCB CX870 ADAPTER PCB (Ref. No. of EXPLODED VIEW : C3) (Ref. No. of EXPLODED VIEW : C51)
Page 13
Explanatory Photos for DISASSEMBLY • The angles from which the photos are taken are shown by "Photo angle:A, B, C, D". • See the diagram below about the shooting direction of each photograph. • Photographs with no shooting direction indicated were taken from the top of the unit. •...
1. FRONT PANEL ASSY TOP COVER → FRONT PANEL ASSY Proceeding : (1) Remove the screws. View from the bottom (2) Cut the wire clamp, then remove the connector wires and FFC. Remove the screws. Front side CN602 STYLE PIN CN916 STYLE PIN CN915 CX870 Model CN321 CY920 Model...
2. RADIATOR ASSY TOP COVER → FRONT PANEL ASSY → RADIATOR ASSY Proceeding : (1) Remove the screws. View from the bottom (2) Cut the wire clamp. Remove the screws. (3) Cut the wire clamp, then remove the connector wires. CN461 CN704 CN701 CN702 CN703...
3. DIGITAL PCB TOP COVER → BACK CHASSIS → DIGITAL PCB Proceeding : (1) Remove the screws. Remove the Nut and Washer form the antenna connector. (2) Cut the wire clamp, then remove the connector wires and FFC. STYLE PIN CX870 ONLY CN903 CON1 CON2 CN916 CN704 CN914 ANT. CX870 Model STYLE PIN STYLE PIN CN321 CY920 Model (3) Remove the connector. Front side BN24A BN26A BN25A...
4. VIDEO PCB TOP COVER → BACK CHASSIS → DIGITAL PCB → SIDE CONNECT PCB → VIDEO PCB Proceeding : (1) Remove the FFC and the screw. (2) Remove the connector and remove the side connect PCB. BN21B BN28B BN27B PCB HOLDER SIDE CONNECT PCB 5. INPUT and HDAM PCB TOP COVER → BACK CHASSIS → DIGITAL PCB → VIDEO PCB → INPUT and HDAMPCB Proceeding : (1) Remove the connector.
6. SPK PCB Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB → SIDE CONNECT PCB → VIDEO PCB → INPUT and HDAM PCB → → FRONT CONNECT and FUSE PCB SPK PCB (1) Remove the screws. View from the bottom (2) Remove the connector wire.
(4) Remove the connector wire. Remove the screws. CN971 7. SMPS PCB Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB → SMPS PCB See "EXPLODED VIEW" for instructions on how to remove each PCB of the "SMPS PCB". 8. TRANS POWER Proceeding : TOP COVER → BACK CHASSIS → DIGITAL PCB → TRANS POWER See "EXPLODED VIEW" for instructions on how to remove each PCB of the "TRANS POWER".
SPECIAL MODE Special Mode Configuration Buttons No. 1 -12, 15 : Hold down buttons"A", "B" and "C" at the same time and press the power button to turn on the power. No. 13, 14 : Hold down buttons "A" and "B" for at least 3 seconds while the power is on. No.
1. Version Display Mode 1.1. Actions Version information is displayed when the device is started in this mode. 1.2. Starting up Hold down buttons "DIMMER" and "STATUS" at the same time and press the power button to turn on the power. Press the "STATUS"...
Page 22
u GUI SFLASH : G U I : X X Y Z * * * * X X : Model code Y : Model Z : Region(U=1, N=2, K=5, F=4) i Ethernet 1st Boot Loader, Hardware ID : E t h e r n e t F B L * * * * * * - A A AA :Hardware ID...
Page 23
1.4. Error display See the table below for descriptions of displayed errors and countermeasures for these. Display order is q , w , e , r , t , y , u . Condition States Display TROUBLE SHOOTING The model name, brand name and region F I R M E R R O R information written in the firmware are...
Page 24
1.5. Version Display in the Setup Menu Follow the steps below to display the firmware information. (1) Press the "SETUP" button on the remote control. (2) Select "General - Information - Firmware". The version information is displayed as a 14-digit number as shown in the screenshot below. General/Firmware XXXX-XXXX-XXXX-XX Version...
2. PANEL / REMOTE LOCK Selection Mode 2.1. Actions Turn the PANEL LOCK and REMOTE LOCK modes on and off. 2.2. Starting up Hold down buttons "BACK" and "ENTER" at the same time and press the power button to turn on the power. Select the mode using the button "CURSOR f / d ", and press the button "ENTER"...
3. Selection Modes for Service-related Operations 3.1. Actions Select diagnostic mode (service path check mode), protection history display mode, or 232C standby clear mode. 3.2. Starting up Hold down buttons "ZONE SELECT" and "BACK" at the same time and press the power button to turn on the power. Select the mode using the button "CURSOR f / d ", and press the button "ENTER"...
Page 28
3.4. DIAGNOSTIC MODE (Video/Audio (signal) path confirmation mode) 3.4.1. Specification This mode is used for confirming the Video and Audio (signal) paths. (Troubleshooting) Confirming the operation of unit can be easily done after repair. Backup data will not be lost. 3.4.2.
Page 29
Confirmation item FL display Settings Contents of confirmation HDMI (signal) Path Input Source : CBL/SAT ·HDMI Input ⇒ Speaker output ( Front L/R ) A 0 5 H D M I Input Mode : HDMI ( fixed ) ·HDMI Input ⇒ Preout output ( Front L/R ) fig.05a, fig.05b, fig.05c Vol.: 60.0 ( -20.0dB ) * * * .
Page 30
Confirmation item FL display Settings Contents of confirmation Front Wide (signal) Path Input Source : CBL/SAT ·Analog input ⇒ Speaker output ( Front Wide L / R ) A 1 5 F W Input Mode : Auto ·Analog input ⇒ Preout output ( Front Wide L / R ) fig.12a, fig.12b Sound mode: MULTI CH STEREO * * * .
Page 31
3.5.6 Video system confirmation items fig. XX: Refer to the block diagram of the fig.XXth. Confirmation items FL display Settings Contents of confirmation Analog Video through (signal) Path Input Source : CBL / SAT ·Component input ⇒ Component output V 0 1 V I D E O Video Convert ( IP Scaler ) : OFF, All sources fig.17 * * * .
Page 32
fig.01 SR7009 ANALOG AUDIO BLOCK R2A15220 HDAM PREOUT FL_VOL RY871 MAIN_FL PREOUT_FL PREOUT_FL AUDIO IN DAFL MAIN ZONE2 ZONE3 TONE PREOUT_FL 78,79 EXT_FL PREOUT_FR 74,75 BLU-RAY PREOUT_FL FR_VOL PREOUT_SW1 70,71 CBL/SAT MAIN_FR CBL/SAT PREOUT_FR 72,73 DAFR PREOUT_SW2 TONE 76,77 EXT_FR 82.83 PHONO MEDIA...
Page 33
fig.02a SR7009 ANALOG AUDIO BLOCK R2A15220 HDAM PREOUT FL_VOL RY871 MAIN_FL PREOUT_FL PREOUT_FL AUDIO IN DAFL MAIN ZONE2 ZONE3 TONE PREOUT_FL 78,79 EXT_FL PREOUT_FR 74,75 BLU-RAY PREOUT_FL FR_VOL PREOUT_SW1 70,71 CBL/SAT MAIN_FR CBL/SAT PREOUT_FR 72,73 DAFR PREOUT_SW2 TONE 76,77 EXT_FR 82.83 PHONO MEDIA...
Page 75
3.6. Protection History Display Mode 3.6.1. Actions This mode records and displays an event in which the THERMAL, CURRENT, ASO or DC protection was activated. If protections have been activated multiple times, the latest protection operation is recorded. 3.6.2. Starting up Hold down buttons "ZONE SELECT"...
Page 76
3.6.4. Clearing the Protection History There are two ways to clear the protection history. (a) Start Protection History Display Mode. Press the button "STATUS" to display the protection history. Press and hold the button "ENTER" for 3 seconds. P R O T E C T H I S T O R Y : D C Press and hold the button "ENTER"...
Page 77
3.8. Operation Info Mode 3.8.1. Actions This mode displays the accumulated operating time, power on count and each protection count. 3.8.2. Starting up Hold down buttons "ZONE SELECT" and "BACK" at the same time and press the power button to turn on the power. Select the "4.
3.9. TUNER STEP mode (N only) 3.9.1. Actions This is a special mode for enabling reception STEP of the ANALOG TUNER to be changed. 3.9.2. Starting up Hold down buttons "ZONE SELECT" and "BACK" at the same time and press the power button to turn on the power. Select the "5.
5. CX870 / CY920 Initialization mode 5.1. Actions The following items are initialized. (1) Favorites (2) Quick Select (3) Presets (4) Internet Radio Recently Played (5) Flickr contacts (6) User ID (7) Resume Playback station 5.2. Operations (1) Select "Online Music" (2) Hold down buttons "BACK"...
JIG FOR SERVICING The following jigs (extension cable kit) are used when repairing the PCBs. Order the jigs from your dealer if necessary. CAUTION : Incorrect connections may cause malfunction. • Connection of Jig for DIGITAL PCB -Items to Be Prepared- 8U- 110084S EXTENSION UNIT KIT 1 Set...
Page 81
BN21B BN28B BN27B PCB HOLDER BN24C BN26C From AMP PCB CN706 BN64C CN481 BN23C HDAM (3) Remove the DIGITAL PCB from the chassis and turn it over. Place an insulation sheet larger than the PCB underneath the DIGITAL PCB. Connect the earth of the PCB to the chassis using an earth wire, etc. PCB INPUT PCB VIDEO PCB DIGITAL...
Page 82
(4) Connect the expansion cables. PCB FRT CNT PCB HDMI PCB SIDE CNT PCB FRT CNT PCB VIDEO PCB SIDE CNT PCB VIDEO PCB SIDE CNT Connection table of Board to Board Ref. No. Ref. No. 15pin CN27A SIDE CNT BN27A DIGITAL 27pin...
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC. The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows. Procedure after PCB Name Ref. No. Description Remark Replacement DIGITAL IC151 R5F56108VNFP SOFTWARE:Main DIGITAL IC171 R5F5210ABDFP SOFTWARE:Sub IC254/IC264/ DIGITAL MX25L1606EM2I-12G SOFTWARE:DSP1 / 2 / 3 / 4 ROM IC273/IC283 DIGITAL IC404...
Page 84
1.2. Unzip Download File Unzip the downloaded file on your computer. SR7009U USB_SR7009_XXXXXXXXXXXX-XXXX.zip copy to USB flash drive You can find "firmwares" folder after unzipped. Copy that folder to USB flash drive. You have to put "firmwares" folder on root directly on USB flash drive(memory). 1.3.
Page 85
1.4. Insert the USB memory in the USB port. NOTE:Remove the LAN cable from this unit when performing updates. Download firmware in USB flash drive. 1.5. Start the update. Hold down buttons "HDMI OUT" and "STATUS" at the same time and press the power button to turn on the power. 1.6.
Page 86
1.9 Forced USB All Device Write Mode 1.9.1. Actions Mode used when this unit cannot be recovered. Forcibly switches this unit to USB update mode. 1.9.2. Operations Press the "HDMI OUT" and "STATUS" buttons simultaneously while inserting the AC plug to turn the power on. 1.9.2.
Page 87
1.11. About the error code See the table below for error codes and details of faults when the firmware is updated through USB memory. Error USB Update Error Display Details of Error code Coping strategies Code C o n n e c t i o n f a i l Disconnect and connect the USB mem- Unable to detect USB.
Page 88
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. M a i n * * * m i n Block Write failed while rewriting If the FL display stops at the Error dis- Main. U p d a t i n g f a i l play, press and hold the "Power opera- tion" button for five seconds.
Page 89
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. M a i n * * * m i n Time Out in USB Check. If the FL display stops at the Error dis- C o n n e c t i o n F a i l 3 9 play, press and hold the "Power opera- tion" button for five seconds.
Page 90
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several NACK received in response or no times. Wait until the FL display stops. S u b * * * m i n response from Sub for L com- If the FL display stops at the Error dis- U p d a t i n g f a i l mand. play, press and hold the "Power opera- tion" button for five seconds.
Page 91
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several Abnormal data in Update Packet times. Wait until the FL display stops. G U I * * * m i n received from CX870 / CY920 If the FL display stops at the Error dis- U p d a t i n g f a i l (PacketNoError). play, press and hold the "Power opera- tion" button for five seconds.
Page 92
Error USB Update Error Display Details of Error code Coping strategies Code This unit automatically retries several times. Wait until the FL display stops. E t h e r I M G * * * m i n Failed to transit to Application If the FL display stops at the Error dis- Mode. U p d a t i n g f a i l play, press and hold the "Power opera- tion" button for five seconds.
2. Updating by DPMS Download the latest firmware from the internet and update the firmware. 2.1. Network Connection (1) System Requirements • A broadband internet connection • Modem • Router • Ethernet cable (CAT-5 or greater recommended) (2) Settings Internet Computer Modem ComputerLAN port / Ethernet connector...
Page 94
2.3. About the error code See the following table for details on the error code, details of the error code, display and coping strategies when updating the firmware from DPMS. (D&M Product Management Server) Error DPMS Update Error Display Details of Error code Coping strategies Code Initialize the unit and try updating...
Page 95
Error DPMS Update Error Display Details of Error code Coping strategies Code Abnormal data in Update Packet M a i n * * * m i n Turn on the power again. Update will received from CX870 (Packet No start automatically. U p d a t i n g f a i l Error). M a i n * * * m i n Block Erase failed before rewriting Turn on the power again. Update will...
Page 96
Error DPMS Update Error Display Details of Error code Coping strategies Code Check the network connection. Update M a i n * * * m i n Connect Time Out by DPMS con- in an environment where there is a nection. C o n n e c t i o n F a i l 3 9 small network load.
Page 97
Error DPMS Update Error Display Details of Error code Coping strategies Code NACK received in response or no S u b * * * m i n Turn on the power again. Update will response from Sub for L com- start automatically. U p d a t i n g f a i l mand. S u b * * * m i n No Update Packet received from Turn on the power again. Update will...
Page 98
Error DPMS Update Error Display Details of Error code Coping strategies Code Check the network connection. Update E t h e r I M G * * * m i n IP Address acquisition failure in an environment where there is a (Time Out). C o n n e c t i o n F a i l A 1 small network load.
Page 99
Device display during firmware update Display of target device during firmware update. Target device DPMS Update Display Error code when an error occurs M a i n * * * m i n 10 - 16 Main CPU 36 - 3F U p d a t i n g * * % 50 - 52 S u b...
ADJUSTMENT Audio Section Adjusting Idling Current Required measurement equipment: DC Voltmeter 1. Preparation (1) Avoid direct blow from an air conditioner or an electric fan, and adjust the unit at normal room temperature 15 °C ~ 30 °C (59 °F ~ 86 °F). (2) Presetting •...
Contents Connections Playback Settings Tips Appendix SOUND MODES AND CHANNEL OUTPUT Sound modes and channel output S This indicates the audio output channels or surround parameters that can be set. D This indicates the audio output channels. The output channels depend on the settings of “Speaker Config.” (v p. 236). Channel output Front L/R Center...
Contents Connections Playback Settings Tips Appendix Surround Parameter Dialog Tone MultEQ XT32 ® Dynamic EQ Dynamic Audyssey Audyssey M-DAX Sound mode Enhancer Volume ® Direct/Pure Direct (2-channel) Direct/Pure Direct (Multi-channel) DSD Direct (2-channel) DSD Direct (Multi-channel) Stereo Multi Ch In Dolby Surround DTS Neo:X Audyssey DSX...
Page 103
Contents Connections Playback Settings Tips Appendix 2-channel signal Multi-channel signal Analog / Dolby DTS-HD DTS ES DTS ES Dolby Dolby Dolby Dolby Sound mode NOTE Digital (-HD) (Super Multi Express Dscrt6.1 Mtrx6.1 Atmos TrueHD Digital Digital (Super (+/HD) Audio Plus (EX) Audio Multi Ch In...
TROUBLE SHOOTING 1. POWER 1.1. The unit does not power on The unit does not power on Does the power indicator Does the power indicator on on the front panel flash in the front panel flash in red green or white when the when the power is turned on? power is turned on? Has a fuse broken?
2. Analog video Perform the operation below beforehand.- b Check it whether connection cable and Monitor are normal. b VIDEO Convert is set to ON. b Setting as follows. V : SAT COMPONENT : SAT MONITOR OUT (CVBS/Cmponent/HDMI) output NG Input Input CVBS...
Page 106
The VIDEO PCB is faulty. Use the jigs to extend the DIGITAL PCB. Check power supply voltage and I2C control signal of video selector IC.(IC511) V+3.3V : J5043 Power supply IC (IC513) flaw. V-5V : J5042 SIDE CNT PCB(BN28B) flaw. I2C(SCL) : J5046 Video selector IC(IC511) の...
(7) Are the HDMI output settings of the Blu-ray/DVD player correct? and set the HDMI output correctly. (8) If using a marantz Blu-ray/DVD player, is the "HDMI" indicator of the fluorescent display lit? Proceed to YES if using a Blu-ray/DVD player from another compa-...
Page 109
(11) Are a picture and sound output when a different Blu-ray/DVD The Blu-ray/DVD player is faulty. player is used? Check the TV. Use a TV that supports HDCP. Computer monitors can- (12) Does the TV support HDCP? not be used. If the TV does not support 1080P/4K, a picture cannot be (13) Does the TV support 1080P/4K? output even if the Blu-ray/DVD player is set to 1080P/4K.
4. AUDIO 4.1. AUDIO CHECK No audio output See "Audio Check PATH"(121 page) CHECK1 INPUT SURROND MODE SOURCE Check the ANALOG AUDIO BLOCK Audio output OK? ANALOG 2CH DIRECT ANALOG CHECK2 INPUT SURROND MODE SOURCE Check the DIGITAL AUDIO BLOCK Legacy Audio output OK? COAX or OPT...
Page 111
4.2. Power AMP (AMP PCB) No audio output. Protection is activated. Is the power transistor open or short circuit- Replace the power transistor. 2SB1647/2SD2560 Is the emitter resistor of the power transis- tor open? Replace the emitter resistor. 0.47 Ω Is the base resistor of the power transistor open? Replace the base resistor.
Page 112
4.3. Analog audio No audio output. Is a voltage of ± 7V supplied to SIDE Repair the ± 7V power supply. CNT PCB CN64C 4-7pin? Is there an audio signal in INPUT PCB Repair the power amplifier. CN461? Connect the connectors correctly. Is electron volume serial data be- Is the connector correctly connected ing sent to SIDE CNT PCB CN23C...
5. Network/Bluetooth/USB 5.1. Cannot connect to the network Check the connection environment Insert the LAN cable correctly and then turn Is the LAN cable correctly inserted? on the power again. Check the connection environment Set the IP address, etc. correctly. If the IP settings are fixed, check that no Are the network settings of this unit correct? other devices have the same IP address and...
Page 114
Can an output voltage (3.3V) to Is E_POWER1 (IC151 uCOM 53pin) The circuit of E_POWER1 between Q1107(FET_SW) be confirmed? "Hi" ? IC151 and Q1107 are faulty. The circuit around Q1107(FET_SW) is faulty. Can an output voltage (1.2V) to IC115 Is E_POWER4 (IC151 uCOM 56pin) The circuit of E_POWER4 between be confirmed? "Hi"...
Page 115
5.2.1. Cannot connect to the Bluetooth (Case of CX870 model) Check the Bluetooth Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Enable the Bluetooth function and try connecting Is the Bluetooth function enabled on the Bluetooth device? again.
Page 116
5.2.2. Cannot connect to the Bluetooth (Case of CY920 model) Check the Bluetooth Is the Bluetooth device compatible with the A2DP profile? Use a device that is A2DP profile compatible. Enable the Bluetooth function and try connecting Is the Bluetooth function enabled on the Bluetooth device? again.
Page 117
5.3. A connected USB device is not recognized. Check the USB device being used Is a USB hub being used? Do not use a USB hub. Is the USB device supported by this unit? This unit supports devices in the FAT16 and FAT32-for- matted mass storage class, MTP-compatible devices and iPods (with the exception of some models).
6. SMPS DC 5V is not output. Replace the IC901 (TOP256YN) and Is IC901 (TOP256YN) damaged? D9001 / D9002 / D9003 / D9004. Has a fuse (F9001) broken? Replace the damaged part(s). Are there the damage in IC901 / D9001 / D9002 / D9003 / D9004 / C90040? Are there any short circuits caused by Repair the short circuited area(s) by the...
Page 120
Operation waveform for each part OPTION AC100 ~ 120V CCQF2E104KZE-T Primary drain After primary side rectification AC220 ~ 240V OPEN (Caution: High voltage, electric shock) (Caution: High voltage, electric shock) C9002 0.01uF 250V OPTION HEATSINK (16*16*30) D9001 1N4007 or CHASSIS After secondary rectifications D9002 1N4007 D9012...
LEVEL DIAGRAM SR7009 LEVEL DIAGRAM FRONT ch LINE IN HDAM MUTE PRE OUT GAIN PCM1690 ADJ. + + + - - R2A15220FP ANALOG H/P OUT + SPEAKER EXT IN R2A15218FP +30dB 4.22Vrms:A/D FULL SCALE SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω...
Page 124
SR7009 LEVEL DIAGRAM CENTER ch HDAM MUTE PRE OUT GAIN PCM1690 + ADJ. + - - R2A15220FP + SPEAKER EXT IN R2A15218FP +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS +10dB...
Page 125
SR7009 LEVEL DIAGRAM SUBWOOFER ch HDAM MUTE PRE OUT GAIN PCM1690 ADJ. + + - - R2A15220FP + SPEAKER EXT IN R2A15218FP +30dB MAX. SIGNAL LEVEL R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms Differential Out PCM1690 DOLBY LIMIT LEVEL (ALLch-3dBFS) 2.83Vrms=0dBFS +20dB +20dB -10dBFS +10dB +10dB...
Page 126
SR7009 LEVEL DIAGRAM SURROUND ch HDAM MUTE PRE OUT GAIN PCM1690 + ADJ. + - - R2A15220FP + SPEAKER EXT IN R2A15218FP +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS +10dB...
Page 127
SR7009 LEVEL DIAGRAM SURROUND BACK ch PCM1690 + + - - R2A15220FP + SPEAKER EXT IN R2A15218FP MUTE PRE OUT HDAM GAIN ADJ. +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS...
Page 128
SR7009 LEVEL DIAGRAM FRONT WIDE/HEIGHT1/DHIEGHT2 ch PCM1690 + + - - R2A15220FP + SPEAKER R2A15218FP HDAM MUTE PRE OUT GAIN ADJ. +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω Differential Out PCM1690 2.83Vrms=0dBFS MAX. SIGNAL LEVEL +20dB +20dB DOLBY LIMIT LEVEL (ALLch-3dBFS) +29dB -10dBFS +10dB...
Page 129
SR7009 LEVEL DIAGRAM ZONE2/ZONE3 LINE IN To MAIN PCM5100 MUTE PCM5100 MONO R2A15220FP NJW1149V MONO MONO NJW1149V + SPEAKER MONO R2A15218FP MUTE Z2/3MONO from D/A F-ch from D/A SB-ch from D/A FH/FW-ch +30dB SP OUT R2A15218FP/R2A15220FP MAX. OUTPUT 3.8Vrms 4.48Vrms/8Ω PCM5100 MAX.
TO 2C TO DIGITAL CNT (Mz : PAGE 23) (Mz : PAGE 19) TO LEVEL CHG. TO A4 A3,4 TO A6 R1585 4.7K 4.7K R1586 R1587 4.7K R1577 4.7K R1578 OPEN OPEN R1579 R1580 OPEN R1581 OPEN R1582 OPEN R1583 OPEN OPEN R1584...
TO A5 (Mz : PAGE 19_A4) TO DIGITAL CONNECT (Mz : PAGE 19_B1) TO DIGITAL SUPPLY POWER TO C1 DETECT SR7009 ONLY SR7009 ONLY CN203 OPEN R1904 4.7K DGND T206 T186 T185 Q1907 Q1910 Q1913 Q1901 2SC3052 2SC3052 2SC3052 T188 T189 RT1N141C T246...
(Mz : PAGE 26_A4) (Mz : PAGE 25_A4) (Mz : PAGE 26_D4) (Mz : PAGE 26_D2) FROM DSP1 PART TO A.PLD PART FROM DSP1 PART FROM DSP1 PART TO E8 TO F6 TO F3 TO F2 5 6 7 8 5 6 7 8 1 2 3 4 1 2 3 4...
TO F7 (Mz : PAGE 28_D4) (Mz : PAGE 25_A4) (Mz : PAGE 26_D2) TO F0 FROM DSP3 PART ADUDIO PLD PART FROM DSP1 PART TO F4 IC282 C2855 1000P A3V56S40GTP-60 256M BIT SDRAM C2847 C2856 VDD_INT DAI_P09 R2845 DSP4_FLAG0 FLAG0 DAI_P05 DQ15...
(Mz : PAGE 22_B6) (Mz : PAGE 25_A3) TO SUB CPU TO AUDIO PLD TO F1 TO D0 A+5V ADINL ADINR DAGND C3055 C3056 C3057 1000P C3058 1000P C3059 OPEN C3060 OPEN C3061 1000P C3062 1000P C3063 1000P C3064 1000P C3065 OPEN C3066...
TO B5 TO G8 (Mz : PAGE 19_B3) (Mz : PAGE 25_D1) FROM DIGITAL POWER TO AUDIO PLD IC422 OPEN MCU&CY920 TO C6 TO MAIN CPU VPLD_TRANS2 VPLD_TRANS2 VPLD_TRANS1 (Mz : PAGE 21_B1) VPLD_TRANS1 ADV8003 VPLD_TRANS0 VPLD_TRANS0 TO SUB CPU RGB/YC R4201 R4216...
TO 1H TO CN64C TO CN24C TO CN23C TO BN89B FROM PREOUT FROM SIDE CONNECT PART FROM FRONT CONNECT PART TO PREOUT FROM SIDE CONNECT PART (PAEG 12_D6) (PAEG10_B4) (PAEG 7_B2) (PAEG 10_D6) (PAEG 10_B2) CN89A (PAGE 14_D1) BN64C BN64C BN24C C125Z2 SR7009 :...
SIDE CNT_CUP12631Z(CONNECT A) CN23A CN27A TO BN23A TO BN27A FROM DIGITAL CON.PART FROM DIGITAL CON.PART SR7009/AV7702 : PAGE 17_D1 SR7009/AV7702 : PAGE 17_C1 CN23A CN27A C125Z1-27 C125Z1-15 SR7009/AV7702 USA VER. ONLY IC961 PQ033DNA1ZPH R9621 C9602 Specific IC C9615 10/50V R9601 R9607 OPEN R9622...
R9821 MODEL SR7009 AREA EU/AP JPN/CHN OPTION A TUNER PART C9827 R9825 OPEN OPEN C9821 OPEN C9825 L9821 OPEN OPEN R9823 R9827 OPEN C9809 OPEN C9810 OPEN CHASSIS R9826 C9828 OPTION A OPEN OPEN C9826 C9811 L9822 OPEN OPEN 0.1uF R9824 CHASSIS R9828...
CN69A SR7009/AV7702 PAGE 19_B1 TO CN69B TO DIGITAL CON. FRONT B'D VOLUME & REMOTE PART CN69A C6918 OPEN C6917 OPEN LUG61 OPEN C6916 IC603 C6915 OPEN FL602 CHASSIS NJM2887 C6914 OPEN GP1261AI C6913 OPEN R6354 C6912 0.1uF R6353 4.7K C6911 0.1uF R6352 4.7K...
EXPLODED VIEW Please refer to the last chapter for the part list. C53-1 C53-2 CX870 ONLY CY920 ONLY CX870 ONLY WARNING: Parts marked with this symbol z have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
SEMICONDUCTORS Only major semiconductors are shown, general semiconductors etc. are omitted to list. The semiconductor which described a detailed drawing in a schematic diagram are omitted to list. 1. IC's R5F56108VNFP (DIGITAL : IC151) PE0/D8 PC4/A20 PD7/D7 PC5/A21/SCK5/CS5#-D PD6/D6 PC6/A22/RxD5/CS6#-D PD5/D5 PC7/A23/TxD5/CS4#-D/CS7#-D PD4/D4...
Page 185
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY 16 MD0 M3VPu 17 P86 (CEC POWER2) Reserve (CEC POWER2 control) REMOTE 232C POWER SUPPLY (REMOTE 3.3V) 18 P85 POWER(232C) control pin.(ON: H) 19 RES# RESET Reset input (reset: L) 20 XTAL XTAL Clock input...
Page 186
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY ETHERNET communication control pin 53 P56/TRDATA2 E SPI MOEI N3VPu (DM860) HDMI Tx/ip Scaler/OSD RESET control 54 P55/TRDATA1 ADV8003 RST SW3VPu pin (ADV8003) ETHERNET communication control pin 55 P54/TRDATA0 E SPI MIEO N3VPu (DM860)
Page 187
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY PA5/A5/PO21/ Master Volume rotation detection TIOCA7/TIOCB7/ VSEL B pin(Rotary encoder) TCLKG PA4/A4/PO20/ E POWER 2 Unused TIOCA7 (Reserve) PA3/A3/PO19/ DAC (ETHER) MUTE control pin TIOCC6/TIOCD6/ DAC(ETHER) MUTE (PCM5100 for DM860) TCLKF PA2/A2/PO18/ PRE Z2 MUTE...
Page 188
Pull up/ Pin Name Symbol LvCnv STBY STOP Function down STBY H/P DET / MIC MIC detection / Headphone detection 134 P46/IRQ14-B/AN6 DET/THERMAL A / HEAT PROTECT-A detection pin 135 P45/IRQ13-B/AN5 KEY3 SW3VPu Button input 3 136 P44/IRQ12-B/AN4 KEY2 SW3VPu Button input 2 137 P43/IRQ11-B/AN3 KEY1...
Page 189
RX210 Group 1. Overview R5F5210ABDFP (DIGITAL : IC171) RX210 Group PLQP0100KB-A (100-pin LQFP) (Top view) VREFL0 VREFH0 AVCC0 AVSS0 R5F5210ABDFP Terminal Functions Note: • This figure indicates the power supply pins and I/O port pins. For the pin configuration, see the table “List of Pins and Pin Functions (100-Pin LQFP)”.
Page 190
Symbol Pin Name Pu/Pd LvCnv STBY Function STBY 35 PH3 HSDA HDMI I2C- MN8647781 3VPu 36 PH2/IRQ1 HSCL HDMI I2C- MN8647781 3VPu 37 PH1/IRQ0 778_1_HINT HDMI MN8647781(TX) HDMI INT input pin 38 PH0 778_2_RST HDMI MN8647781(RX) RESET control pin ※ 39 P55 778_2_HINT HDMI MN8647781(RX) HDMI INT input pin...
Page 191
Symbol Pin Name Pu/Pd LvCnv STBY Function STBY 85 PD1/IRQ1 DSP1CS DSP control pin (ADSP21487KSWZ-3B) 3VPu 86 PD0/IRQ0 DSP1FLAG0 DSP control pin (ADSP21487KSWZ-3B) 87 P47/AN007 88 P46/AN006 VIN A COMPOSITE VIDEO SELECT IC(NJM2595) 89 P45/AN005 VIN B COMPOSITE VIDEO SELECT IC(NJM2595) 90 P44/AN004 VIN C COMPOSITE VIDEO SELECT IC(NJM2595)
Page 197
A3V56S30FTP A3V56S40FTP 256M Single Data Rate Synchronous DRAM A3V64S40GTP-60 Pin Function Pin Descriptions SYMBOL TYPE DESCRIPTION Clock: CLK is driven by the system clock. All SDRAM input signals are sampled on the positive edge of CLK. CLK also increments the internal burst counter and controls the output registers. Input Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal.
Page 198
A3V56S30FTP A3V56S40FTP 256M Single Data Rate Synchronous DRAM A3V64S40GTP-60 Block Diagram Note:This figure shows the A3V56S30FTP The A3V56S40FTP configuration is 8192x512x16 of cell array and DQ0-15 Type Designation Code A 3V 56 S40F TP-G6 Speed Grade 75: 133MHz@CL=3 7: 143MHz@CL=3 6:...
Page 202
PCM1690(FRONT CNT : IC301 / IC311) PCM1690 Pin Function TERMINAL PULL- DESCRIPTION NAME DOWN TOLERANT RSV2 — — — Reserved, tied to analog ground RSV1 — — — Reserved, left open RSV2 — — — Reserved, tied to analog ground RSV1 —...
Page 203
TERMINAL PULL- DESCRIPTION DOWN TOLERANT NAME VOUT1+ Positive analog output from DAC1 VOUT1- Negative analog output from DAC1 PCM1690 RSV2 45 — — — Reserved, tied to analog ground AGND2 46 — — — Analog ground 2 VCC2 47 — —...
Page 204
CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control BLOCK DIAGRAM AND PIN CONFIGURATION (TOP VIEW) R2A15220FP (INPUT : IC471) TRER MUTE AVEE AVCC BASSR2 AVEE BASSR1 ADCL 0/-6/-12/-18dB TREL ADCR SUB2 AGND BASSL2 MAIN INR1 BASSL1 Bass/ Treble 0~-95dB, +42~0dB -14~+14dB...
Page 205
R2A15220FP R2A15220FP CONFIDENTIAL 8-CHANNEL ELECTRONIC VOLUME With 14-Input selector And Tone control PIN DESCRIPTION R2A15220FP Pin Function PIN No. Function Name FROUT,FLOUT, 22,20, COUT,SWOUT, 16,14, Output pin of FL/FR/C/SW/SL/SR/SBL/SBR channel SROUT, SLOUT, 10, 8, SBROUT,SBLOUT 2, 100 23,19, FR Pre-out,FL Pre-out, Pre-output pin of FL/FR/SL/SR/SBL/SBR channel 11, 7, SR Pre-out, SL Pre-out,...
Page 208
FRONT FRONT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 209
FRONT REF No. Part No. Part Name Remarks Q'ty New C6014 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUS1H104KCS C6021 CAP,ELECT(50V/10uF) CCEA1HH100T C6022,6023 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUS1H104KCS C6025 CAP,ELECT(50V/1uF) CCEA1HH1R0T C6027 CAP,ELECT(50V/1uF) CCEA1HH1R0T C6034 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUS1H104KCS C6046 CAP,ELECT(50V/1uF) CCEA1HH1R0T C6052 CAP,ELECT(50V/10uF) CCEA1HH100T C6071-6073 CAP,CHIP(1608,50V/100pF,C0G)_SAMSUNG GeneralCapacitors-C0G CCUS1H101JAS C6081 CAP,CHIP(1608,50V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R...
Page 210
FRONTCNT FRONTCNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 212
7CHAMP 7CHAMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 215
7CHAMP REF No. Part No. Part Name Remarks Q'ty New R7745 RES,CARBON(1/5W,22Kohm,J) CRD20TJ223T CAPACIITORS GROUP C7001 CAP,CHIP(1608,50V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUS1H103KCS C7011,7012 CAP,ELECT(10V/330uF) CCEA1AH331T C7013 CAP,ELECT(10V/47uF) CCEA1AH470T C7101 00D2544574919 CAP,ELECT(50V/47uF),ELNA/RA3 CCEA1HRA3470T C7102 CAP,PE-FILM(100V/470pF/J) CCME2A471JR11T C7104 CAP,PE-FILM(100V/220pF/J) CCME2A221JR11T C7106 00D2544569937 CAP,ELECT(25V/220uF,ELNA/RA3) CCEA1ERA38P221T C7107 CAP,MYLAR(50V/2200pF/J) HCQI1H222JZT C7112...
Page 216
2CHAMP 2CHAMP PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 218
INPUT INPUT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 222
H-DAM H-DAM PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 225
VIDEO VIDEO PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 226
SPK PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 228
CNT PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 229
SMPS SMPS PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 231
DIGITAL REF No. Part No. Part Name Remarks Q'ty New Q1913-1917 943214500020S T.R,2SC3052 CVT2SC3052 Q2002,2003 963216500060S T.R,RT1N144C(10K-47K) CVTRT1N144C Q3841,3842 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q3851,3852 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q3861,3862 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q3871,3872 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q3941,3942 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q3951,3952 943216500020S T.R,RT1N141C(10K-10K) CVTRT1N141C Q3961,3962...
Page 232
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R1530 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R1531-1536 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1538 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1539 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R1540 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1542-1544 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1547 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1551-1554 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1560 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1562-1565 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R1569,1570 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T...
Page 233
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R2052 RES,CHIP(1608/5%/820ohm) CRJ10DJ821T R2053 RES,CHIP(1608/5%/680ohm) CRJ10DJ681T R2054,2055 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R2201 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R2202-2206 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R2208-2250 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R2251-2253 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R2254-2257 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R2260-2264 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R2266-2277 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R2501 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T...
Page 234
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R2754-2757 RES,CHIP(1608/5%/33ohm) CRJ10DJ330T R2759 RES,CHIP(1005/5%/10ohm) CRJ06IJ100T R2760 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R2761 RES,CHIP(1005/5%/10ohm) CRJ06IJ100T R2801 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R2802-2804 RES,CHIP(1005/5%/4.7Kohm) CRJ06IJ472T R2805 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R2807 RES,CHIP(1608/5%/1Mohm) CRJ10DJ105T R2808 RES,CHIP(1608/5%/1.8Kohm) CRJ10DJ182T R2809-2812 RES,CHIP(1005/5%/33ohm) CRJ06IJ330T R2813,2814 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T...
Page 235
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R3903-3906 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R3907 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R3908 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R3909 RES,CHIP(1005/5%/47ohm) CRJ06IJ470T R3910-3912 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R3913-3915 RES,CHIP(1005/5%/47Kohm) CRJ06IJ473T R3916 RES,CHIP(1608/5%/1Kohm) CRJ10DJ102T R3917 RES,CHIP(1608/5%/1Mohm) CRJ10DJ105T R3921 RES,CHIP(1005/5%/47ohm) CRJ06IJ470T R3922 RES,CHIP(1005/5%/1Kohm) CRJ06IJ102T R3923 RES,CHIP(1005/5%/47ohm) CRJ06IJ470T...
Page 236
DIGITAL REF No. Part No. Part Name Remarks Q'ty New R5004 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5005 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5006 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5007 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5008 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5009 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R5010,5011 RES,CHIP(1005/5%/100ohm) CRJ06IJ101T R5012,5013 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5016 RES,CHIP(1005/5%/10Kohm) CRJ06IJ103T R5017-5019 RES,CHIP(1005/5%/0ohm) CRJ06IJ0R0T R5021 RES,CHIP(1005/5%/0ohm) CY920 Model...
Page 237
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C1162 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG HighCapacitance-X5R CCUC0J106KCS C1163 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG HighCapacitance-X7R,X7S CCUS1A105KCS C1164 CAP,CHIP(1608,50V/5pF,C0G)_SAMSUNG GeneralCapacitors-C0G CCUS1H050CAS C1165 CAP,CHIP(2012,6.3V/22uF,X5R)_SAMSUNG GeneralCapacitors-X5R CCUC0J226KCS C1166 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG HighCapacitance-X5R CCUC0J106KCS C1169 CAP,CHIP(2012,50V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUC1H104KCS C1171 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C1172 CAP,CHIP(2012,6.3V/10uF,X5R)_SAMSUNG HighCapacitance-X5R CCUC0J106KCS C1173 CAP,CHIP(1608,10V/1uF,X7R,X7S)_SAMSUNG HighCapacitance-X7R,X7S...
Page 238
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C2594,2595 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C2596 CAP,CHIP(1005,50V/1000pF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1H102KCS C2597 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C2598 CAP,CHIP(1005,50V/1000pF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1H102KCS C2599 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C2602-2609 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C2610,2611 CAP,CHIP(1608,50V/18pF,C0G)_SAMSUNG GeneralCapacitors-C0G CCUS1H180JAS C2612 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C2614-2644 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R...
Page 239
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C3521 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3522 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3523 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3524 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3525 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3526 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG HighCapacitance-X5R CCUS0J475KCS C3528 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3529 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3531 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG HighCapacitance-X5R...
Page 240
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C3666 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3667 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3668 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3669 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3670 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3671 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3672 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C3673 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C3681 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG HighCapacitance-X5R...
Page 241
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C3990 CAP,ALUMINUMELECTROLYTIC(16V/10uF) CCEC1CMVG100T C4001 CAP,CHIP(1608,50V/18pF,C0G)_SAMSUNG GeneralCapacitors-C0G CCUS1H180JAS C4002 CAP,CHIP(1608,50V/15pF,C0G)_SAMSUNG GeneralCapacitors-C0G CCUS1H150JAS C4005 CAP,CHIP(1005,50V/33pF,C0G)_SAMSUNG GeneralCapacitors-C0G CCUI1H330JAS C4006 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C4009 CAP,CHIP(1608,16V/0.15uF,X7R,X7S)_SAMSUNG HighCapacitance-X7R,X7S CCUS1C154KCS C4010 CAP,CHIP(1005,25V/0.012uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E123KCS C4011 CAP,CHIP(1608,16V/0.15uF,X7R,X7S)_SAMSUNG HighCapacitance-X7R,X7S CCUS1C154KCS C4012 CAP,CHIP(1005,25V/0.012uF,X7R)_SAMSUNG GeneralCapacitors-X7R...
Page 242
DIGITAL REF No. Part No. Part Name Remarks Q'ty New C4180 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C4181 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C4182 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C4183 CAP,CHIP(1005,25V/0.01uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1E103KCS C4201-4216 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C4219 CAP,CHIP(1608,6.3V/4.7uF,X5R)_SAMSUNG HighCapacitance-X5R CCUS0J475KCS C4220-4223 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R CCUI1C104KCS C4224 CAP,ALUMINUMELECTROLYTIC(16V/10uF) CCEC1CMVG100T C4301-4303 CAP,CHIP(1005,16V/0.1uF,X7R)_SAMSUNG GeneralCapacitors-X7R...
Page 243
DIGITAL REF No. Part No. Part Name Remarks Q'ty New L4010 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L4012-4016 FERRITECHIPBEAD(1608/60R,CB03YTYH600) CLZ9R005V L4301-4308 FERRITECHIPBEAD(2012/220R) CLZBLM21PG221SN L4311-4313 RES,CHIP(1005/5%/0ohm*2) CRJ062IJ0R0T L4314 943113100000S COMMONMODEFILTER(1210,90ohm) EXC24CH9000U,90OHM,CUTOFFFREQ6GHz CLZ9Z188Z L4321-4323 RES,CHIP(1005/5%/0ohm*2) CRJ062IJ0R0T L4324 943113100000S COMMONMODEFILTER(1210,90ohm) EXC24CH9000U,90OHM,CUTOFFFREQ6GHz CLZ9Z188Z L5091 RES,CHIP(2012/5%/0ohm) CY920 Model CRJ18AJ0R0T L5111,5112 COMMONMODEFILTER(2012,90ohm) 2012,90ohm CLZ9Z174Z...
Page 244
CX870CONNECTOR CX870CONNECTOR PCB ASS'Y ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Page 246
EXPLODED REF No. Part No. Part Name Remarks Q'ty New 411510120032M 4KEYBUTTONASS'Y SG CBT1A1170YA 943412101120M BUTTON,11KEY BK CBT1A1169B37 943411101970M BUTTON,11KEY SG CBT1A1169RMD10 454510002018M HOLDER,DOORAV8003 BK CKG1A053B37 417510015039M HOLDER,DOOR SG CKG1A053RMD10 943411101980M BUTTON,CURSOR BK CBT1A1171Z 943411101990M BUTTON,CURSOR SG CBT1A1171RMYD10 CUSHION,EVA 70x35x3t CHG1A590 SHEET,SCREW CGX1A439...
Page 247
PACKING PACKING ※Parts indicated by "nsp"on this table cannot be supplied. ※The parts listed below are only for maintenance. Therefore they might differ from the parts used in the unit in appearances or dimensions. NOTE:The symbols in the column Remarks indicate the following destinations. U : North America model N : Europe model K : China model F : Japan model B : Black model SG : Silver Gold model...
Need help?
Do you have a question about the SR7009/U1B and is the answer not in the manual?
Questions and answers