Preset Memory - Marantz SR7001 User Manual

PRESET MEMORY

With this unit you can preset up to 60 FM/AM stations
in any order.
For each station, you can memorize the frequency
and reception mode if desired.
AUTO PRESET MEMORY
This function automatically scans the FM and AM
band and enters all stations with proper signal
strength into the memory.
2. 4. 1. 3. 2.
AV SURROUND RECEIVER SR8001
INPUT SELECTOR
PURE DIRECT SURROUND
DISP MULTI AUTO TUNED ST SPKR A B V-OFF PEAK ATT ANALOG
DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 NIGHT EQ DIGITAL
L C R
AAC PCM LFE
DSD SL S SR
SURROUND MULTI
MODE AUTO MULTI SPEAKER BAND T-MODE MEMORY CLEAR
7.1CH INPUT DISPLAY
SPEAKERS
PURE DIRECT THX MultEQ A/B
STANDBY ENTER
MENU EXIT
POWER ON/STANDBY PHONES
MIC
1.
To select FM , press the BAND button on the
front panel.
2.
While pressing the MEMORY button, press the
1 cursor button.
"AUTO PRESET" will appear on the display,
and scanning starts from the lowest frequency.
3.
Each time the tuner fi nds a station, scanning
will pause and the station will be played for fi ve
seconds.
During this time, the following operations are
possible.
The band can be changed by the BAND button.
4.
If no button is pressed during this period, the
current station is memorized in location Preset
02.
If you wish to skip the current station, press the
3 cursor button during this period, this station
is skipped and auto presetting continues.
5.
Operation stops automatically when all 50
preset memory positions are fi lled or when auto
scanning attains the highest end of all bands.
If you desire to stop the auto preset memory at
anytime, press the CLEAR button.
50
MANUAL PRESET MEMORY
3. 2. 4.
DIRECT DISP MULTI AUTO TUNED ST SPKR A B V-OFF PEAK ATT ANALOG SURROUND
DIGITAL DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MTX 6.1 NIGHT EQ
L C R
AAC PCM LFE
SL S SR
SD
DO
SURROUND MULTI
MODE AUTO MULTI SPEAKER BAND T-MODE MEMORY CLEAR
7.1CH INPUT DISPLAY
SPEAKERS
PURE DIRECT THX MultEQ A/B
ENTER
MENU EXIT
DIG
MIC
5.
(Using the SR7001)
1.
READY
Tune into the radio station you desire (Refer to
VOLUME
the "MANUAL TUNING" or "AUTO TUNING"
DOWN UP
section).
2.
Press the MEMORY button on the front panel.
AUX 1 INPUT "– –" (preset number) starts blinking on the
DIGITAL S-VIDEO VIDEO L AUDIO R
display.
3. Select the preset number by pressing the 1
or 2 cursor buttons, while this is still blinking
(approx. 5 seconds)
4.
Press the MEMORY button again to enter. The
display stops blinking.
The station is now stored in the specifi ed preset
memory location.
(Using the remote control unit)
1.
Tune into the radio station you desire (Refer to
the "MANUAL TUNING" or "AUTO TUNING"
section).
2.
Press the MEMO button on the remote. "– –"
(preset number) starts blinking on the display.
3.
Enter the desired preset number by pressing
the numeric buttons.
Note:
• When entering a single digit number (2 for example),
either input "02" or just input "2" and wait for a few
seconds.
RECALLING A PRESET STATION
DSS
TV DVD VCR
TUNER TUNER CD CD-R MD
TAPE AUX1 AUX2 AMP
LIP.SYNC
PREV MUTE
LIGHT
GUIDE
1 2
MENU EXIT
RC8001SR
TEST CH.SEL SURR
Learning Remote Controller
1 1 2 2 3 3
7.1CH ATT SPK-AB 3.
4 4 5 5 6 6
(Using the SR7001)
DISP OSD SLEEP
7 7 8 8 9 9
THX 2.
CLEAR 0 0 MEMO MEMO
1.
Select the desired preset station by pressing
the 1 or 2 cursor buttons on the front panel.
(Using the remote control unit)
1.
Press the TUNER button twice within two
seconds on the remote.
2.
Press the > button until PAGE4 is displayed
3.
Press the P-SET+ (D4) or P-SET– (D5) button
to tune in the deseired preset station.
Or enter the preset station number with the
numeric buttons.
PRESET SCAN
CH CH VOL
1.
2.
OK
LIP.SYNC USE PAGE 2
PREV MUTE MUTE
GUIDE
TUNER TUNER CD
TAPE AUX1
LIGHT
1
RC8001SR
Learning Remote Controller
(Using the remote control unit)
1.
Press the TUNER button twice within two
seconds on the remote.
2.
Press the > button until PAGE2 is displayed
and press the P-SCAN (D4) on the remote.
"PRESET SCAN" appears on the front display
and then the preset station with the lowest
preset number is recalled fi rst.
3.
Preset stations are recalled in sequence (No.1
→ No.2 → etc.) for 5 seconds each.
No stored preset number will be skipped.
4.
You can fast forward the preset stations, press
the > button until PAGE4 is displayed and
press the P-SET+ (D4) continuously.
5.
When the desired preset station is received,
cancel the preset scan operation by pressing
the CLEAR button or P-SCAN (D4) on the
remote.
CH CH VOL
M
4.
D1
2.
D2
OK
D3 5.
D4 D4
2.
LIP.SYNC
D5 D5
PREV MUTE MUTE
GUIDE
MENU EXIT
TEST CH.SEL SURR
1 2 3
CD-R MD
4 5 6
1.
DISP OSD SLEEP
5.
AUX2 AMP
7 8 9
THX
2
0
CLEAR CLEAR MEMO