Advertisement
MiNi
D Stereo Amps
FUNCTIONS AND FEATURES
REAR
FRONT
IN
IN
REAR
FRONT
BOOST
X-OVER
FREQ
GAIN
GAIN
FREQ
X-OVER
BOOST
R
R
1
FLAT
FLAT
FLAT
0dB
12dB
LPF
HPF
40Hz 400Hz MIN
MAX
MIN
MAX
40Hz 400Hz
HPF
LPF
0dB
POWER
L
L
MiNi D1000.4
2
3
4
5
1
POWER LED: When lit up, the amplifier is functioning properly.
GAIN CONTROL: Available only on the D1000.4, set based on the head unit's
2
output voltage. Note, this is not a volume control. Always start at the MIN
and slowly increase the gain. Stop as soon as distortion is heard then lower
the gain until the distortion disappear and only clear sound is produced.
RCA INPUT: Low level input of the D1000.4 is 0.2V to 5V RMS while the
3
D1500.2 & D3000.4 is 0.2V to 10V RMS. Be sure to use a HIGH LOW
LEVEL adaptor if the head unit has only speaker output.
4
XOVER SWITCH & FREQUENCY ADJUST: Used to adjust the boosted center
frequency.
BASS BOOST: Available only on the D1000.4, used to add 0 - 12dB to the
5
chosen center frequency.
LINE LEVEL CONTROL: Available only on the D1500.2 & D3000.4 with a
6
range of 0.2V to 10V RMS.
SUBSONIC FILTER: Available only on the D1500.2 & D3000.4, used to protect
7
the speakers from harmful low frequencies and DC Voltage. Note that the
subsonic filter only takes effect when the amplifier is in full range mode.
SIGNAL SENSING SWITCH: Available only on the D1500.2 & D3000.4.
8
Please refer to page 6-7 for the explanation of this feature.
RCA OUTPUT: Available only on the D1500.2.
9
4
Specifications are subject to change without notice
INPUT
LEVEL
SUBSONIC
X-OVER
OUTPUT
R
10V
0.2V
15Hz
30Hz
LPF
FLAT
HPF
20Hz
500Hz
L
AUTO ON
REMOTE ON
RESET
MiNi D1500.2
3
6
7
8
4
3
12dB
MiNi
D Stereo Amps
R
L
+
RR
+
9
10
+
FR
+
10
SPEAKER CONNECTION: Each amplifier has bridgeable speaker outputs.
Note that the minimum impedance in bridged mode is 4-Ohm.
11
GROUND TERMINAL: Connect to vehicle's chassis/ground using a short 4
gauge cable (2 feet maximum in length).
12
REMOTE TERMINAL: Connect remote cable to the head unit's remote
terminal. If multiple amplifiers are installed in the same system, additional
relays may be necessary.
13
+12V BATTERY TERMINAL: Connect to battery positive (+) using a 4 gauge
cable.
14
FUSES: Used as an added protection from damaging excessive current. Be
sure to use the proper fuse rating in your installation (see page 12).
PROTECTION LED: Available only on the D1500.2 & D3000.4. When lit up
15
upon powering on, the amplifier may be in self-test mode. If this LED stays
on, shut down the amplifier and locate what may have triggered the amplifier
to protection mode. If problem persists, call or e-mail our technical support
team for further assistance.
NOTE: Be sure to follow the wiring preparations/guidelines as listed on the next
page to ensure proper installation.
FUNCTIONS AND FEATURES
GND
REM
RL
FUSE
+12V
REM
GND
11
12
FL
GND
REM
+12V
14
13
12
11
+12V
FUSE
–
. . . . . .
BRIDGE
. . . . . .
+
–
L
+
–
R
+
PWR
PROT
SPEAKER
13
14
1
15
10
. . . . . .
. . . . . .
FUSE
+
BRIDGE
–
+
FL
+
FR
PWR
PROT
+
+
RL
RR
5
www.earthquakesound.com
Advertisement
