Manley 75/150 SE/PP 807 MONOBLOCK Owner's Manual

Manley laboratories, inc. owner's manual 75/150 se/pp 807 monoblock

Advertisement

MANLEY
LABORATORIES, INC.
OWNER'S MANUAL
75 / 150 SE / PP
807 MONOBLOCK
MANLEY LABORATORIES, INC.
13880 MAGNOLIA AVE.
CHINO, CA. 91710
TEL: (909) 627-4256
FAX: (909) 628-2482
email: emanley@netcom.com
http://www.manleylabs.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 75/150 SE/PP 807 MONOBLOCK and is the answer not in the manual?

Questions and answers

Summary of Contents for Manley 75/150 SE/PP 807 MONOBLOCK

  • Page 1 MANLEY LABORATORIES, INC. OWNER'S MANUAL 75 / 150 SE / PP 807 MONOBLOCK MANLEY LABORATORIES, INC. 13880 MAGNOLIA AVE. CHINO, CA. 91710 TEL: (909) 627-4256 FAX: (909) 628-2482 email: emanley@netcom.com http://www.manleylabs.com...
  • Page 2: Table Of Contents

    CONTENTS SECTION INTRODUCTION READ THIS PAGE MAINS CONNECTION CONNECTING YOUR AMPLIFIER DIAGRAM 2 TOP PANEL BIAS PROCEDURES SPECIFICATIONS WARRANTY WARRANTY REGISTRATION PAGE...
  • Page 3: Introduction

    INTRODUCTION THANK YOU!... for choosing the Manley 75 / 150 SE / PP 807 MONOBLOCK Amplifiers. Designed by David Manley, the 807 MONOBLOCK Amplifiers use only the best available components, with the shortest and cleanest signal path possible. These amps have the exclusive Manley ability to switch from Single ended to Push-Pull topologies. This amp is designed to provide our customers with a the unique combination of single ended triode topology, solid power and remarkable specs.
  • Page 4: Read This Page

    - there is a shock hazard if they are removed and children can remove them. Manley Labs can supply an optional "Cover"...
  • Page 5: Mains Connection

    MAINS CONNECTIONS Your amplifier has been factory set to the correct mains voltage for your country. The voltage setting is marked on the serial badge, located on the rear panel. Check that this complies with your local supply. Export units for certain markets have a moulded mains plug fitted to comply with local requirements.
  • Page 6: Connecting Your Amplifier

    CONNECTING YOUR AMPLIFIER Setting up your amplifiers is rather easy. 1. Connect all source components (turntable, CD, Tuner, Tape DAT, etc.) to your preamplifier or switching center. 2. Connect the interconnects from the output of the preamplifier to the RCA input on the top rear of the amplifiers.
  • Page 7: Diagram 2 Top Panel

    MANLEY 75 / 150 SE / PP 807 TRIODE MONOBLOCK RCA Input Jack Speaker Terminals B PLUS FUSE - Replace only with same type and value (MDL 1.5) Mains fuse - Replace only with same type and value IEC Mains socket Output Transformer Power Transformer Power Tube 807 s...
  • Page 8: Bias Procedures

    SWITCHING SINGLE-ENDED 75 / PUSH-PULL 150 This amplifier has a feature exclusive to Manley Labs of being able to choose between two circuit topologies. You are able to switch between each mode while the amplifier is turned on and playing music. In SINGLE-ENDED mode the amplifier uses eight 807s in parallel.
  • Page 9: Specifications

    SPECIFICATIONS Vacuum Tubes: Output Power @ 3% THD Frequency Response +/- 1 dB (measured at 5 watts) Input Sensitivity Input Impedance Load Impedance S/N ratio @ 33 watts Power Consumption Mains Fuse Lamp Dimensions Shipping Weight 8 x 807 (Output), 1 x 7044 (Driver), 1 x 5751 (Input) SINGLE-ENDED: - 72 Watts PUSH-PULL: - 150 Watts...
  • Page 10: Warranty

    WARRANTY All Manley Laboratories equipment is covered by a limited warranty against defects in materials and workmanship for a period of 90 days from date of purchase to the original purchaser only. A further optional limited 5 year warranty is available to the original purchaser upon proper registration of ownership within 30 days of date of first purchase.
  • Page 11: Warranty Registration

    WARRANTY REGISTRATION We ask that you please fill out this registration form and send the bottom half to: Registration entitles you to product support, full warranty benefits, and notice of product enhancements and upgrades. You MUST complete and return the following to validate your warranty and registration.

Table of Contents