1. Manuals
  2. Brands
  3. Ingrasys Manuals
  4. IP Camera
  5. M2210E
  6. User manual

Ingrasys M2210E User Manual

Hide thumbs Also See for M2210E:
Table of Contents

Advertisement

Quick Links

Download this manual
M2210E / V
User's Manual
Version 1.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the M2210E and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Ingrasys M2210E

Summary of Contents for Ingrasys M2210E

  • Page 1 M2210E / V User’s Manual Version 1.1...

  • Page 2: Table Of Contents

    Table of Contents Important Notices – Read Before Use ................2 Overview ......................... 2 Package Contents ......................3 Installation ........................4 Hardware Installation ............................... 4 Software Installation ................................ 8 Discover IP Cameras ................................ 8 Assigning IP Address to the device ..........................8 Discovering devices in Windows Network ........................

  • Page 3: Important Notices - Read Before Use

    Overview Ingrasys M2210 Series is a Full HD, compact IP camera specially designed for buses, trains, and other vehicles applications. The camera comes with 3-axis mechanism design that allows users to adjust the camera's viewing angle for increased installation flexibility.

  • Page 4: Package Contents

    Package Contents M2210(E/V) Product CD Quick Installation Guide Warranty Card Lens Tool VIP Card (Optional) Hardware Pack...

  • Page 5: Installation

    Installation Hardware Installation Connectors Connections Connect the camera to a PoE switch with an Ethernet cable.
  • Page 6 2. Follow the pin definition to crimp the RJ-45 plug onto adaptor and insert a stripped Ethernet cable. the cable. 3. Connect to M2210E RJ-45 rugged Connector and fully seal the connector to achieve waterproof and vibration proof completely. Install M12 Field Installable Feed-Through Adaptor for M2210V Assemble M12 field installable through adaptor to achieve system waterproof and vibration proof.
  • Page 7 3. Connect to M2210V M12 rugged connector and fully seal the connector to achieve waterproof and vibration proof completely Mount Camera Alignment Sticker on drill holes Loosen 2 screws and remove the top cover Route the Ethernet cable through the hole and fasten camera on the surface with 4 screws...
  • Page 8 Tuning lens direction and focus 1. Fit the lens adjustment tool to the lens holder to adjust the direction of the lens. The tilt range is 0°~90° and the pan range is ±60°. 2. Pull out the lens adjustment tool, and turn it around to fit the lens to adjust focus. 3.

  • Page 9: Software Installation

    Software Installation Discover IP Cameras Discovery Tool is a utility provided for not only searching and displaying the available IP cameras information in a network but also managing the multiple networking settings such as static IP address assignment. After completing the hardware installation, run ingrasysDiscovery.exe to search for the IP camera installed. Assigning IP Address to the device The steps of applying this search tool are described as below.
  • Page 10 Step2: Input desired IP information The default settings of account /password are Admin / Admin. If that were been changed, please enter the set values. [Auto Set IP] This is applied to a group of specific cameras selected from the Device List. Step1: Select specific cameras Step 2: Input Account / Password The default account information is Admin / Admin.

  • Page 11: Discovering Devices In Windows Network

    Step 3: Input IP information Discovering devices in Windows Network If the IP camera is installed in a network with DHCP and UPnP services, after obtaining an IP address from DHCP server, it can then be discovered in “Windows Network” of a client PC, see figure below. The reason for ...

  • Page 12: Activex Add-On Installation

    ActiveX add-on Installation It is recommended to use Internet Explorer 8 or later as the primary browser to access the IP cameras website. The first-time access to the camera webpage will be prompted to install the ActiveX. To allow the installation, click “Install”...
  • Page 13 NOTE: If, however, there is not any prompted message or ActiveX cannot be installed at all, it is needed to change the IE security level and settings. <Example> Internet Explorer 9: Internet Options  Security  Custom level Ensure the “Download signed ActiveX controls” setting is either “Enable” or “Prompt” selected.

  • Page 14: Accessing The Camera

    Launch IE browser and input the IP address of the camera or Click on “Browse” button on the selected IP camera address from Ingrasys Discovery Tool. NOTE: Ingrasys IP cameras also support the other web browsers for viewing the live video such as Firefox, Google Chrome or Safari.
  • Page 15 The example given below is the live video displayed with QuickTime player. 3. NVR / CMS Software Ingrasys IP cameras are ONVIF conformant products. Most of ONVIF conformant NVR / CMS software can retrieve the video from the cameras for both live view and recording. For more details...

  • Page 16: The Live View Page

    The Live view page The following illustration shows you the front page of Ingrasys IP camera website. Quick Index Live Window Video Stream Operations Live Video Window Quick Functional Buttons...
  • Page 17 Snapshot: Press the button to capture an image photo Record: Press the button to start recording. Press again to stop it. Record Path: set up a file path that video clips and snapshots can be stored. Full screen: Press the button to enter the full screen mode. Press ESC key to return. Manual trigger: Press the button as triggering an event.

  • Page 18: Video

    Video This section describes how to configure the video streaming of the device, and the related camera image  configurations. Users with Administrator or Operator authority (see System User Management) would intend doing these configurations. Click on “Setup” of Quick Index to enter the Video page shown as below. There are 2 sub-settings under “Video”: −...
  • Page 19 Camera Setting Image Setting Brightness: the luminance of image view. Default value is 8; adjustable from 0 to 16. Contrast: the ratio of luminance of white to black. Default value is 8; adjustable from 0 to 16. Saturation: colorfulness of a color related to its own brightness. Default value is 8, adjustable from 0 to 16.
  • Page 20 Day/Night Day/Night Mode: Switch the video images for Day (plenty of light) or Night (Low light) scene. In default “Auto” mode, camera will switch to Day or Night vision according to the light intensity. The Day / Night modes contain 2 actions: switching IR Filter On / Off, and image hue Color / Mono. In day mode, the IR filter is switched in to avoid the image sensor from receiving the infrared, thus the true color image is provided.
  • Page 21 : represents the Day mode : represents the Night mode The setting items with the Day or Night mode symbol will be altered along with the setting of Day/Night mode. The examples are illustrated as below.
  • Page 22 Video Setting Video Stream This tab provides detailed stream configurations. These settings can affect video size, quality. The maximum transmission performance can be expected under the condition of full network bandwidth. The camera supports up to 3 video streams. Each stream can be configured with following items.
  • Page 23 Video Format: H.264, MPEG4 and MJPEG are available for the selection. The demand of bandwidth and storage requirement differs from the selection of video format. In the request of same video quality, H.264 contributes to less bandwidth and storage requirement, which can be more efficient than MPEG4 or MJPEG.
  • Page 24 Video Overlay The camera supports stamping text information on the video images. The options of the date/time string or/and a line of text message (e.g. camera name or location) are available for displaying on the images. Privacy Mask Privacy Mask can block out the specific areas from view. The blocked areas will not be seen in both live view and recorded video clips and the total of 8 profiles can be created to the list.

  • Page 25: Network Configuration

    Network Configuration The IP Camera acts as one of the network devices. It allows user to configure the network functionalities based on applications. This section will describe the network configurations. Fundamentally, for instance, the IP assignment of the device can be done via DHCP server, static IP option or PPPoE to obtain IP from the service provider.
  • Page 26 Enable PPPoE Service: This service is usually provided by an ISP (Internet Service Provider). IP Camera can establish a dial-up connection to the ISP and then get connected to Internet. (Only IPv4) NOTE1: If you would like to connect camera with IPv6 address, please note that this only works if your network environment and hardware equipment support IPv6.
  • Page 27 Quality Service Quality Service provides network traffic management to guarantee the quality of services in higher priority, especially when network is insufficient. DSCP (Different Service Code Point) is a 6-bit IP header which defines the service level of the packet. According to the DSCP value, routers with PHB (Per-Hop Behavior) will define a specific class of traffic for the packet, in terms of bandwidth, latency, or loss rate, etc.
  • Page 28 HTTP port / HTTPS port: By default, the HTTP and HTTPs ports are set to 80 and 443 respectively. They can also be assigned to another port number between 1025 and 65535. The HTTP port is basically provided for device’s webpage access. When the video format is set to MJPEG, user is able to retrieve the live video via HTTP URL, e.g.
  • Page 29 Access IP Filter This setting also provides a basic security by filtering the accesses from other hosts. Enable this function and choose “Allow / Deny” of the listed IP addresses. Up to 15 IP address can be added in the list.

  • Page 30: Recording

    Recording This section provides the recording configuration on the camera. Unlike the recording function (Quick Functional Button) on the live view page, video can also be recorded to the storage attached to the local network storage (Samba) according to a time based schedule. There are 4 subdirectories in the “Recording”...
  • Page 31 Dest. (Destination): The stored path for the recording file Remove: Click to delete this recording plan. Add / Edit Recording Plan Plan Name: Identifier of the recording plan Video Source: The selection of the video source to be recorded. Options: Stream1 / Stream 2 / Stream 3. Maximum File Size: This option defines the maximum file size of each video clip.
  • Page 32 Normally, inserting the micro SD card will be done before entering this page and obtain the card information as below. However, if it is the other way around, click SD storage tab to refresh it. SD Card Status: • Syncing: Display when the card database is in the process of synchronization •...
  • Page 33 Searching the Records The SD storage would keep massive records after the “recording plan” and/or “event handling” (see Event Management) has been launched. The search criteria are provided to look for particular records in the SD card. Example: Trigger Type – Schedule Recording...
  • Page 34 There are 3 categories of search criteria: 1. Trigger Type: It includes Motion Detection, Manual Trigger, Network Fail and Periodically as the type of “triggered-by-events” and Schedule Recording as the type of “triggered-by-schedule”. 2. Trigger Time: Input Date / Time rage that recording was created. 3.

  • Page 35: Event Management

    Event management Event management describes the handling of events with the corresponding actions. A common case can be exampled is storing a captured image to a local storage (Actions), when there is a Motion Event (Trigger Condition). This chapter gives the configurations of Triggers (what to detect?) and Actions (“what to send”...
  • Page 36 Server Name: Identifier of the event server Server Type Email: Send the media file via email when an event is triggered. • Mail Server Address: Enter a host name or IP address of the email server. • User Name: Enter the user name of the email account. •...
  • Page 37 Media Type There are 2 types of media (file) available, snapshot (.jpg image) and video clip (.avi). Video Source: Select the video source to be captured Pre-alarm / Post-alarm image(s): Enter the numbers of images that will be captured before and after trigger is activated.
  • Page 38 Event List List a summary of configured events. That is the selection of trigger condition(s) and the corresponding actions, as well as the scheduling. Up to 10 event objects can be configured. To begin with it, click on “Add New” button to extend for the detailed configurations.
  • Page 39 Event Name: Enter an event name, e.g. Motion Detection, to identify this configured event. Select All: 24 hrs/ 7days (Mon-Sun) continuous recording Scheduled Pattern: User-defined time frame Triggered by: This describes the selection of trigger conditions which include: • Motion Detection: Select the motion detection area(s) used for trigger condition. To enable and configure the motion detection areas, go to Motion Configuration.

  • Page 40: Examples Of Event Handling

    Examples of Event Handling The following cases are provided as the examples of Event Handling. Scenario While viewing live video, user can manually trigger an event anytime simply by pressing the button, on the web page. It will send email to the specified email accounts with the captured pictures. The configurations are illustrated as below: Step 1: Add Event Server •...
  • Page 41 • Click on “Apply” to save the email server and media settings. Step 3: Configure Event List • On Event List page, click on “Add New” button. • Enable and configure this event - Event of manual triggering - Click the check box to enable this event. Give a name of this event setting;...

  • Page 42: System Options

    System options System Options provide users to obtain and configure the system settings of the IP camera system. It contains the page of System Information, Date and Time, User Management, Maintenance and Log Service. The details about each subcategory will be described as below. System Information The page gives the general information of the IP camera system.
  • Page 43 Date and Time This section describes the date/time adjustment for the IP camera system. The ways to adjust the IP camera’s date/time can be Synchronize with NTP Server, Synchronize with PC or Set Manually. Current Date & Time Display current system date/time of the IP camera. The date format can be changed from the drop-down list under Configure Date &...
  • Page 44 User Management By default, the access to the camera is not user authenticated. For security, the IP camera should be restricted only authenticated accounts to access. It is able to enable/disable user accounts, as well as to manage the added users in this page. Initially, there is a default account, Admin in the “User List”.
  • Page 45 NOTE: The backup file can be applied to other Ingrasys IP cameras, so users won’t need to configure each device. It is recommended to switch the IP setting to DHCP mode before exporting the backup file.

  • Page 46: Troubleshooting

    Troubleshooting Check firmware version Firmware version may imply the functionalities’ updates or availability in the camera system. Therefore, in the first step of troubleshooting and then reporting, it helps to locate the found issues. Newer version firmware may have these issues corrected. The version code can be found in Setup ->...
  • Page 47 [Steps of Firmware Upgrade] 1. Go to firmware upgrade page on the web. Figure 1 2. Click “Firmware” button to load the firmware image. Figure 1 3. Click “Upgrade” to begin (the upgrade progress bar will pop up). Figure 2 4.

  • Page 48: Recover Device Settings

    Recover device settings In some cases, camera system does not respond to any operation. A certain recovering processes would help to get the unit back to initial status, so that it can resume operable / configurable. This will be the operations on the “Reset Button”.

  • Page 49: Led Indicators

    LED Indicators There are 2 type of LED indicators; LED for Network Status (green) and LED for system and power (bicolor, blue and orange). These LEDs can help to recognize the current device status. 1. LEDs for Network Status: Green Cable Disconnect 10 Link / Traffic (Activity) Flashing...

  • Page 50: Technical Specifications

    File upload via FTP, SMTP and SAMBA and Micro SD Card; Event Management Event Actions Notification via FTP, email ; Video and audio recording to SD or SAMBA. I/O Connectors RJ45 Ethernet connector(M2210E) Network Connector & Indicators M12 Ethernet connector(M2210V)
  • Page 51 Power Input PoE (IEEE 802.3af class 3) Power Consumption 5W max 1 x Networking status (Green) LED indicator 1 x System status (Blue & Orange) Reset Reset button on board Memory Card Micro SD/SDHC card slot Weight Net: 460 g (1.017 lb) Dimensions Ø4.89”...

This manual is also suitable for:

M2210v

Table of Contents