Kleenmaid KFL1600 Manual

Test program KFL1600

MANUEL ACTION
Press and hold buttons
START/PAUSE and
EASY IRONING and
turn round the program
knob for 1 step in left
(anti-clock side)
~10"
~12"
~4"
~70"
~12"
~77"
~30"
~42"
~62"
ACTIVITY
Self test of micro is executed and test program begins:
- all segments on LCD goes ON for 2 sec.
- after 2'' on top line write SELF TEST , on bottom line
write max. spin speed for cotton and 99L and all symbols
are ON
- check if is Water clean sensor connect
(read voltage at empty drum)
- check if is pressure sensor (Huba) connect
(read voltage at empty drum)
All step can be 10".

Door lock control (text on top line DOOR)

- contact is close at once

NTC control (text on top line NTC))

check resistance of NTC (can be between 10 to 40°C)
Min. 2 sec.

Water filling (text on top line WATER)

Open the valves Hot Water, Main Wash and Pre Wash.
Water goes in 3 different space in dispenser.
- HW : 5 '' (space 2), if it is connected to hot/cold water
- PW : 5'' (space 1)
- MW : 5'' (space 2)
- PW + MW : to reach level 1 (space 1,2 and 3)
- pause 2''
- MW : to level 110 mm H
2
Max. time for all is 70 sec.

Water clean sensor (text on top line WATER SENSOR)

Only check if it is connected (check voltage at water in
drum together 10")

Washing and heating (text on top line WASHING)

- Washing: 15''ON / 5''OFF / 15''ON / 5''OFF
- 3 times repeats washing
- last wash in spin direction
- Heater ON all time of washing
- JET pump ON all time of washing
All together is 75''. After this time switch OFF heater
and JET pump ; washing goes to spinning.

Spinning with water (text on top line SPIN)

- 30'' spin from 50rpm to max.500
- wait to drum stop

Draining (text on top line DRAIN)

- switch pump ON for 40 ''
Check if water level fall under level 1

End spinning (text on top line SPIN SPEED)

- pump stay ON
- 10'' spin from 0 rpm to max. rpm
(if necessary switch ON tape field)
- 50'' on max. spin speed
- wait to drum stop
- switch OFF all component
O
INDICATION
•
If self test O.K, than on top line
write SELF TEST OK (for 2'')
and all other segments and symbols
switch OFF
•
If self test is not O.K., than on top
line write SELF TEST ERROR
(for 2'') all other segments and
symbols switch OFF, WM stop
•
If it is O.K. than on top line write
DOOR OK (for 2'')
•
If it is not O.K. than on top line
write DOOR ERROR, WM stop
•
If it is O.K. than on top line write
NTC OK (for 2'')
•
If it is not O.K. than on top line
write NTC ERROR
•
If it is O.K. (reach level on
pressure-switch) than on top line
write WATER OK (for 2'')
•
If it is not O.K. (not reach level on
pressure-switch) than on top line
write WATER ERROR (for 2'')
•
If it is reach level (110 mm H
than on top line write WATER
FILL OK
•
If not reach level (110 mm H
in 70'', than on top line write
WATER FILL ERROR, WM stop
•
If it is connected than on top line
write WATER SENSOR YES (for
2'')
•
If it is not connected than on top
line write WATER SENSOR NO
•
If it is O.K. – washing in both
direction, than on top line write
WASHING OK (for 2'')
•
If it is not O.K. than on top line
write WASHING ERROR, WM
stop
•
If it is O.K. than on top line write
DRAIN OK (for 2'')
•
If it is not O.K. than on top line
write DRAIN ERROR, WM stop
•
If it is O.K. than on top line write
SPIN SPEED OK (for 2'')
•
If it is not O.K. than on top line
write SPIN SPEED ERROR, WM
stop
O ),
2
O )
2