Download  Print this page

Makita T221D Instruction Manual

Cordless stapler
Hide thumbs

Advertisement

Cordless
Applicable staples
Stanler
Staple capacity
Dimensions (L x W x H)
Net weight
I
MODEL T221D
MODEL T 2 2 l D W
With Fast Charger
Battery Cartridge 9100
Voltage
Charging time
1 H r .
9.6
V
INSTRUCTION MANUAL
Model DC9700 Fast Charger
Input
output
A.C. only
50 Hz
~
60
Hz
D.C. 7.2 V,
9.6
V
SPEC
IF
I CAT I
0
N
S
Model T221D
199
mm x
58
mm
x
193
m m
(7-7/8"
x
2-114"
x
7-518")
1.7
kg
(3.7
Ibs)
Staple Nos.
*1019, * l o 2 2
1010,
1013,
1016,
I
100
~~~~
*
M a n u f a c t u r e r reserves t h e right t o change specifications
without
notice.
*
N o t e :
1.
Specifications m a y differ f r o m c o u n t r y
to
country.
2.
Staples
with
m a r k are for s o f t material only.

Advertisement

Table of Contents
loading

  Related Manuals for Makita T221D

  Summary of Contents for Makita T221D

  • Page 1 Cordless INSTRUCTION MANUAL SPEC I CAT I Model T221D Applicable staples Staple Nos. 1010, 1013, 1016, *1019, * l o 2 2 Battery Cartridge 9100 Voltage Charging time 1 H r . M a n u f a c t u r e r reserves t h e right t o change specifications...
  • Page 2: Important Safety Instructions

    SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
  • Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool w i t h finger on switch. Be sure switch is 16.
  • Page 4: Important Safety

    Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION - To reduce risk of injury, charge only MAKITA Battery 9000 9100. Other types of batteries may burst causing personal injury and damage.
  • Page 5 ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C or ABOVE 4OoC (104OF). 2. Do not attempt t o use a step-up transformer, an engine generator or receptacle. not allow anything t o cover or clog the charger vents. 4.
  • Page 6: Additional Safety Rules

    ADDITIONAL SAFETY RULES Always wear safety goggles or safety glasses w i t h side shield, and a full face shield when needed. 2. Do not point the ejection port at anyone in the vicinity (especially his face). Keep hands and feet away from the ejection port area. Always remove the battery cartridge before loading the staples, adjustment, inspection, maintenance or after operation is over.
  • Page 7 Installing or removing battery cartridge Always switch off the tool before insertion To remove the battery cartridge, pull out plate on the tool and grasp both s e t sides of the cartridge while withdrawing i t from the tool. *To insert the battery cartridge, align the tongue on battery cartridge with the...
  • Page 8 Safety system Make sure all safety systems are in working order before operation. The tool must not operate if only the trigger i s pulled or if only the safety lever is pressed against the wood. It must work only when both actions are performed.
  • Page 9 To secure the sub-magazine in place, push the sub-magazine while pressing the plate spring on the rear the sub-magazine. CAUTION Always secure the sub-magazine in place, or the staples can drop out and cause problems. With the magazine loaded, if the tool the staples can fall out and present mind especially when working in high locations.
  • Page 10 Driving staples Place the tool on the material to be fastened that the front and the rear of the tool contact the material flat. Do not tip the tool t o the right or left side. firmly against the material, Then pull the trigger to drive the staples.
  • Page 11 CAUTION : Always remove the battery cartridge before attempting to perform inspection or main- tenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts only.
  • Page 12 ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this any other accessories or attachments might present a risk of injury to persons. manual. The use The accessories or attachments should be used only in the proper and intended manner.
  • Page 13 - 2 1 - CORDLESS STAPLER Model T221D Note: The switch and other part configurations may differ from country country.
  • Page 14 MODEL T221D 'i\M DESCRIPTION Switch Housing Set iWlth Item 451 Flat Washer 9 Compression Spring 9 Compression Spring 1 3 Guide Plate Driver Lock P,n 4 Safety Lever Compression Spring 3 Hammer Spring Pin 4 - 1 4 Plate Sleeve 4...
  • Page 15 MAKITA LIMITED O N E YEAR WARRANTY Warranty Policy Evcry Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.

This manual is also suitable for:

T22ldw