Table of Contents
Advertisement
Quick Links
Drywall Screwdriver
Bit shank
No load speed
Overall
size
(RPM)
length
MODEL
Capacities
MODEL 6800DBV
MODEL 6 8 0 l D B V
Net
weight
INSTRUCTION MANUAL
6800DBV
--I
6801DBV
Drywall screws
No. 6
Self drilling screw . . . 5 m m (3116")
DOUBLE
INSULATION
114"
Hex
0
-
2,500
' : : ,
m y
(;::E)
,,4,,
Hex
4,000
280
mm
1.5 kg
( 1 1")
(3.3
Ibs)
Advertisement
Table of Contents
Related Manuals for Makita 6800DBV
Summary of Contents for Makita 6800DBV
- Page 1 INSTRUCTION MANUAL MODEL Capacities 6800DBV Drywall screws No. 6 Self drilling screw . . . 5 m m (3116”) 6801DBV MODEL 6800DBV MODEL 6 8 0 l D B V Bit shank No load speed Overall length size (RPM) 2,500 ’...
- Page 2 SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger on switch. Be sure switch is OFF when plugging in. 16.
- Page 4 VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY to the user the tool.
- Page 5 Removing or installing locator assembly remove the locator assembly, pull the locking sleeve forward and then turn it counterclockwise. To install the locator assembly, screw it clockwise and then push the locking sleeve back in lightly toward the motor. Turn the locking sleeve slightly to match the locking positions and then push in firmly to lock the locator in place.
- Page 6 Initially, adjust the locator assembly t o create a distance of approximately 1 mm from the tip of the locator t o the base of the screw head. One full turn of the locator (1/16") equals change in depth. After adjusting the locator assembly, push the locking sleeve in t o lock the locator in place.
- Page 7 Always be sure that the tool is switched inspection or maintenance. To maintain product SAFETY and RELlABl LITY, reparis, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. &...
- Page 8 ACCESSORIES CAUTION: These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. use of any other accessories The accessories or attachments should be used only in the proper and intended manner.
- Page 9 -07-'93...
- Page 10 Nore T h e sw8tch and other p a r t SpeCiliCatlOnb nlay d i f f e r lrom c o u n t r y MACHINE Rubber Pin Ball Bearing 62718 Model 6800DBV 608LB For Model 6801DBV an sn ARMATURE ASSEMBLY...
- Page 11 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory, It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.