Advertisement
Quick Links
Drywall Screwdriver
MODEL
68OODBV
6801DBV
MODEL 6800DBV
MODEL 680lDBV
Bit shank
No
load speed
Overall
Net
size
(RPM)
length
weight
114" Hex
0
-
2,500
'?fl!?y
(i:zi:)
114" Hex
0
-
4,000
' : : , m y
(i;z&
Capacities
Drywall screws No. 6
Self drilling screw . . . 5
m m
(311 6")
INSTRUCTION MANUAL
DOUBLE
I NSU LATl ON
SPEC IF I CAT1 0 N
S
*
Manufacturer reserves t h e right t o change specifications w i t h o u t notice.
*
Note: Specifications may differ from country t o country.
WARNING: For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS
FOR
FUTURE REFERENCE.
Advertisement
Related Manuals for Makita 68OODBV
Summary of Contents for Makita 68OODBV
- Page 1 INSTRUCTION MANUAL SPEC IF I CAT1 0 N MODEL Capacities 68OODBV Drywall screws No. 6 Self drilling screw . . . 5 6801DBV Manufacturer reserves t h e right t o change specifications w i t h o u t notice.
-
Page 2: Important Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. AVOID UNINTENTIONAL STARTING. Don't carry tool w i t h finger on switch. Be sure switch is OFF when plugging in. 16.
-
Page 4: Additional Safety Rules
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source w i t h voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user the tool. - Page 5 Removing or installing locator assembly To remove the locator assembly, pull the locking sleeve forward and then turn it counterclockwise. To install the locator assembly, screw clockwise and then push the locking back in lightly toward the motor. Turn the locking sleeve slightly to match the locking positions and then push in firmly to lock the locator in place.
- Page 6 Initially, adjust the locator assembly to create from the tip of the locator t o the base of the screw head. One full turn of the locator (1/16") equals change in depth. After adjusting locking sleeve in to lock the locator in place. Drive piece duplicate material.
- Page 7 Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, reparis, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. position for...
- Page 8 ACCESSORIES CAUTION: These accessories or attachments are recommended for use w i t h your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury t o persons. The accessories or attachments should be used only in the proper and intended manner.
- Page 9 -07-’93 SCREWDRIVER Model 6800DBV Model 680 1 DBV Note: The switch, noise suppressor and other part configuratlons differ from country to country.
- Page 10 Note " " 0 " &tD DESCRIPTION Rubber Pin Ball Bearlrlq 627LB For Model 68OODBV 608LB For Model 6801DBV ARMATURE ASSEMBLY i W i t h Item 2 6 Ball Bearing...
- Page 11 MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase.