GE PGP989DN2BB Owner's Manual & Installation Instructions page 15

Installation
i structi
Gas Downdroft
Cooktop
_ If you have questions, call 800.GE.CARES (800.432.2737} or visit our Website at: GEAppliances.com
IN THE COHHONWEALTH OF MASSACHUSETTS:
• This product must be installed by a licensed plumber
or gas fitter.
• When using ball-type gas shut-off valves, they shall be
the T-handle type.
• A flexible gas connector, when used, must not exceed
3 feet.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
• IMPORTANT - save t hese i nstructions forlocal
inspector's use.
• IMPORTANT - Observe all
g overning
codes
and ordinances.
° Note to Installer - Be sure to leave these instructions
with the Consumer.
• Note to Consumer - Keep these instructions for future
reference.
° Unless very knowledgeable in the installation of this
product, engage a professional installer.
• Proper installation is the responsibility of the installer.
• Product failure due to improper installation is not
covered under the Warranty.
FOR YOUR SAFETY
If You Smell Gas:
1. Open windows.
2. Don't touch any electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
WARNING
- Before beginning the installation,
switch power off at the service panel and lock the service
disconnecting means to prevent power from being
switched on accidentally. When the service disconnecting
means cannot be locked,securely fasten a prominent
warning device, such as a tag, to the service panel.
IMPORTANT SAFETY INSTRUCTIONS
Thecooktophasbeendesigncertifiedby Underwriters
Laboratories ( UL). Aswith anyapplianceusinggasand
generatingheat,therearecertainsafetyprecautions you
shouldfollow.You'll f indtheseprecautionsinthe Important
SafetyInformation sectionin the front ofthis Owner'sManual.
Readthemcarefully.
, Besureyourcooktopisinstalledproperlyby a qualified
installer o r servicetechnician.
• The cooktop must be electrically grounded in accordance
with local codes, or in their absence,with the National
ElectricalCode ANSI/NFPANo. 70 - Latest Edition.
• Installation of this cooktop must conform with local codes,
or in the absence of local codes,with the National FuelGas
CodeANSIZ223.1/NFPA54 - Latest Edition.
• Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage. Refer
to this manual. Forassistance or additional information,
consult a qualified installer,service agency, manufacturer
(dealer)or the gas supplier.
• Disconnect electrical supply before servicing.
• Never reuse old flexible connectors. The use of old flexible
connectors can cause gas leaks and personal injury. Always
use NEW flexibleconnectors when installing a gas appliance.
° Make sure the wall coverings around the cooktop can
withstand heat generated by the cooktop up to 200°F.
• Avoid placing cabinets above the cooktop.
• If cabinets are placed above the cooktop, allow a minimum
clearance of SO"between the cooking surface and the
bottom of unprotected cabinets.
• If cabinets are placed above the cooktop, use cabinets no
more than _tS"deep.
° If a 30" clearance between cooking surface and overhead
combustible material or metal cabinets cannot be
maintained, protect the underside of the cabinets above
the cooktop with not lessthan 1/4" insulating millboard or
gypsum board at least 3/16" thick covered with 28 gauge
sheet steel or 0.020"thick copper.
° Clearance between the cooking surface and protected
cabinets HUSTNEVERBE LESS THAN 24" The vertical
distance from the plane of the cooking surface to the
bottom of adjacent overhead cabinets extending closer
than 1"to the plane of the cooktop sides must not be less
than 18".
15