ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications with- out prior notice.
Getting to Know Your Device Appearance The following figure is only for your reference. The actual product may be different. LED Indicators Power Button WPS Button Micro USB Port (U)SIM Card Slot RESET Button microSDHC Card Slot NOTE: microSDHC logo is a trademark of SD-C, LLC.
Indicators Indicator Status Description Error status. Not registered to the mobile network, no (U)SIM card in- Red solid serted or no network service avail- able. Network Green solid Registered to the 2G/3G network. Green Connected to the 2G/3G network blinking and data is being transferred.
Page 5
The battery is empty. Please Red blinking charge the battery. • The battery is low. Please charge the battery. Red solid • The battery is in the over-volt- age charging status. Battery • Blinks every 2 seconds when the battery is being charged. Green •...
Connection Scenario Your device supports two methods to connect to the Internet and supports multi-clients for surfing on the Internet at the same time. The following figure is only for your reference. • 4G Mode: Use your (U)SIM card to access the Internet. Internet Wi-Fi Mode: Your device will connect to other WLAN •...
Installing Your Device Slide the back cover and remove it...
Page 8
Insert the (U)SIM card. IMPORTANT: Your device does not support Micro/Nano SIM card or any other nonstandard SIM cards. To avoid device damage, please do not use them or any card holders. Insert the microSDHC card if necessary. Insert the battery.
Close the back cover. Connecting to Your Device Via Wi-Fi Power on your device directly. Use your normal Wi-Fi application on the client to search for the available wireless networks.
Page 10
NOTE: Please set the client to obtain an IP address automatically referring to the chapter “Configuring your PC”, and then the client will get an IP address like “192.168.0.101”. Select the SSID of your device, and then click Connect. NOTE: Please check the label on your device to get the default SSID. Input the password, and then click Connect.
NOTE: You may need to input the password for Wi-Fi connection. Please check the label on your device to get the default. Wait a moment, and then the client will connect to your device successfully. Via USB Cable Connect to the device.
Page 12
Power on your device. The OS detects and recognizes new hardware and finishes the installation automatically. NOTE: If the system does not launch installation automatically, you can run the installation program in path of My Computer > ZTEMO- DEM. Wait a moment, and then the client will connect to your device successfully.
Accessing the Internet 4G Mode After the client connected to your device successfully, you can ac- cess the Internet in the Automatic or Manual mode. The default mode is Automatic. Mode Operations Your device will connect to the Internet automatically, Automatic and your clients can surf on the Internet directly.
Connect to the WLAN device. There are two methods for your reference. Select the WLAN device which will be listed in the Wi-Fi Hotspot area, and then click Connect. Click Add, input the WLAN device information in the Add Wi-Fi Hotspot area, and then click Apply. After the client connected to the WLAN device successfully, you can access the Internet.
Page 15
Right-click My Network Places, and then select Properties. Right-click Wireless Network Connection, and then select Properties.
Page 16
Select Internet Protocol(TCP/IP), and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically, and then click OK to finish the configuration.
Warning and Notice To the Owner • Some electronic devices are susceptible to electromagnetic interference sent by your device if inadequately shielded, such as the electronic system of vehicles. Please consult the manu- facturer of your device before using if necessary. •...
• Be aware of the usage limitation when using your device at places such as oil warehouses or chemical factories, where there are explosive gases or explosive products being pro- cessed. Turn off your device if required. • The use of electronic transmitting devices is forbidden in air- crafts, at petrol stations and in hospitals.
• Do not use your device immediately after a sudden tempera- ture change. In such case, it will produce dew inside and out- side your device, so don’t use it until it becomes dry. • Handle your device carefully. Do not drop, bend or strike it. Otherwise your device will be damaged.
Any other cause beyond the range of normal usage in- tended for the Product. End User shall have no right to reject or return the Product, or re- ceive a refund for the Product from ZTE under the above-mentioned situations.
Limitation of Liability ZTE shall not be liable for any loss of profits or indirect, special, incidental or consequential damages resulting from or arising out of or in connection with using of this product, whether or not ZTE...
Page 22
Problem Suggested Solution • Make sure the Wi-Fi function is active. • Refresh network list and select the cor- rect SSID. Can not establish • Check the IP address to make sure the Wi-Fi connec- your client can obtain an IP address tion between your automatically in the Internet protocol device and client.
Page 23
About the password • If you changed the password and forgot the new password, you need to restore the device to the factory default settings. For more assistance, please: • Send E-mail to mobile@zte.com.cn • Visit www.ztedevice.com • Call Service Hotline: +86–755–26779999...