How To Fold And Move The Treadmill - Weslo Cadence 830 User Manual

2. See HOW TO LOWER THE TREADMILL FOR USE on
page 12. Follow step 2 on page 12 to lower the treadmill.
Hold the Left Handrail (45) against the left Upright (46)
as shown. (If you are shorter than 173 cm [5 ft. 8 in.],
align the upper two holes in the Handrail with the
holes in the Upright; if you are 173 cm [5 ft. 8 in.] or
taller, align the lower two holes.) Attach the Left
Handrail with two Handrail Bolts (42), two Handrail
Washers (43), and two Handrail Star Washers (44). Do
not tighten the Handrail Bolts yet.
Hold the Right Handrail (65) against the right Upright
(46). Be careful not to pinch the Wires (60). Make
sure that both Handrails are at the same height.
Attach the Right Handrail with two Handrail Bolts (42),
two Handrail Washers (43), and two Handrail Star
Washers (44). Do not tighten the Handrail Bolts yet.
3. Place the Console Base (52) on the Handrails (65, 45)
(only the Right Handrail is shown). Pull out just enough of
the two Wires (60) to connect them to the receptacles in
the Console Base. Make a loop with the indicated plastic
tie and insert the end through the tie holder on the bot-
tom of the Console Base. Locate the Wire that has a two-
pin connector and a three-pin connector. Plug the con-
nectors into the matching receptacles in the Console
Base. If the connectors do not fit easily, rotate them
and then plug them in. Slide the Wire Cover (96) onto
the connectors so that they are completely covered. Next,
plug the other Wire into the other receptacle on the
Console Base. WARNING: Do not connect or discon-
nect the Wires whilst the treadmill power cord is
plugged in. Tighten the plastic tie and cut off the end.
See the inset drawing. Loop the included plastic tie
around the Wire Cover (96) so that the plastic tie is in the
two notches in the Wire Cover. Tighten the plastic tie and
cut off the end.
4. Thread four Screws (2) into the Handrails (65, 45) and
the Console Base (52). Make sure that the Wires (60)
in the Right Handrail are clear of the screw holes.
After all four Screws have been started, tighten the
Screws until they are snug; do not overtighten them.
Tighten all parts used in steps 2 and 3.
5. Attach the Storage Latch (48) to the Upright (46) with
two Screws (2). Be careful not to overtighten the
Screws.
2
60
65
45
46
46
44
60
44
43
42
60
3
52
Tie
96
65
Tie
4
52
60
2
45
65
5
48
2
46
6

HOW TO FOLD AND MOVE THE TREADMILL

HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, UNPLUG THE POWER CORD.
CAUTION: You must be able to safely lift 20 kg (45 lbs.)
in order to raise, lower, or move the treadmill.
1. Hold the treadmill with your hands in the locations shown
at the right. To decrease the possibility of injury, bend
your legs and keep your back straight. As you raise
the treadmill, make sure to lift with your legs rather
than your back. Raise the treadmill about halfway to the
43
vertical position.
42
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left thumb, press the storage
latch and hold it. Pivot the treadmill up until the frame
and foot rail are past the storage latch. Close the storage
latch over the catch. Make sure that the storage latch
is fully engaged over the catch.
To protect the floor or carpet from damage, place a
mat under the treadmill. Keep the treadmill out of
direct sunlight. Do not leave the treadmill in the stor-
age position in temperatures above 30° C (85° F).
96
HOW TO MOVE THE TREADMILL
Before moving the treadmill, convert the treadmill to the
storage position as described above. Make sure that the
storage latch is fully engaged over the catch.
1. Hold the handrails and place one foot on one of the
wheels as shown.
2
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To
reduce the risk of injury, use extreme caution whilst
moving the treadmill. Do not attempt to move the
treadmill over an uneven surface.
3. Place one foot on a wheel, and carefully lower the tread-
mill until the base leg is resting in the storage position.
Closed
Storage
Latch
Catch
Base
Leg
Wheel
11