Utilitech TM-097 S Owner's Manual

ITEM #0192773 Before initial use, if LCD screen is blank, connect with
power for at least 30 minutes to charge the internal
MODEL #TM-097 S
battery. After the screen displays, the unit is ready for
DAYLIGHT SAVING
programming.
IN-WALL TIMER
1. This device is to be installed in a wall box measuring
at least 3 in. x 2 in. x 2-1/2 in. (standard single gang
electrical wall box) and wired in
Strip Length:
Call customer service at 1-866-994-4148, accordance with National Electrical
8 a.m. - 6 p.m., EST, Monday - Thursday,
Code.
8 a.m. - 5 p.m., EST, Friday.
2. Straighten each conductor and strip 3/4 in.
of insulation from each wires.
PACKAGE CONTENTS
A B 3. Installing In-Wall Timer
3
Ground
Neutral
Ground wire (Green)
Neutral
Neutral wire (White)
Hot wire
Load wire (Black)
Hot wire (Black)
Load
wire
C D
1. Insert the ground or bare wire(s) into the hole(s)
labeled "G" (near green screw) (see figure 3).
2. Insert 2 neutral wires into the holes labeled "N"
PART DESCRIPTION QUANTITY
(near silver screw) (see figure 3).
3. Insert the hot wire into the hole labeled "L-I" (near
A Timer 1
brass screw) (see figure 3).
B Wall plate 1
4. Insert the load wire into the hole labeled "L-O"
C Mounting screws (Wall box) 0.748 in. - 2 (near brass screw) (see figure 3).
D Mounting screws (Wall plate) 0.33 in. - 2 5. Tighten all screws firmly
(see figure 3-5).
* Tools Required for Assembly (not included):
6. Carefully fold wire into
flathead screwdriver.
wall box and mount timer
(A) into wall box using
mounting screws (CC),
INSTALLATION INSTRUCTIONS
then attach the wall plate
using the mounting
Warning: To avoid fire and/or shock, turn off power.
Make sure the power is off before wiring. If you are screws (DD).
7. Restore power by flipping the breaker to the "on"
unsure or uncomfortable with installation, contact a
position or re-installing the fuse to the circuit.
licensed electrician.
AB14645
NORTH: NOR / CENTER: CEN / SOUTH: SOU
3-6
NORTH
CENTER
SOUTH
3/4"
(1.9cm)
2. Set an ON/OFF Program for Sunrise/Sunset
This unit's sunrise/sunset schedule is based on USA
astronomic zones. The actual sunrise/sunset
OPERATING INSTRUCTIONS
schedule may slightly differ from east to west. You
Wall
1. Setting the Clock can set the actual sunrise/sunset time today. This
unit will memorize the difference and auto-adjust for
1. Open the door. following dates.
2. Press TIME button.
1. Press button to show
3. Display will flash for a 15 seconds. If no other
current sunrise time
action taken, clock may engage with the incorrect
time. (see Diagram 2-1).
• Press " " to increase
4. Press the " " or " " button until the display shows
number. Press " " to
the current YEAR then press SET/RE button.
5. Press the " " or " " button until the display shows decrease number.
Setting range: MAX
the current MONTH then press SET/RE button.
+/- 1 hour. Once you
6. Press the " " or " " button until the display shows
the current DAY then press SET/RE button. complete the time
7. Press the " " or " " button until the display shows setting press SET/RE button.
2. press " " or " " to turn on or turn off the device
the current HOUR then press SET/RE button.
during the sunrise time. Then press SET/RE
8. Press the " " or " " button until the display shows
the current MINUTE then press SET/RE button. button.
9. Press the " " or " " button to turn on or turn off
3. The display will show
Day-Light-Saving-Time(DST) function then press
SET/RE button. current sunset time
(see Diagram 3-1).
• Press " " to increase
NOTE: When setting the current time during the
Day-Light-Savings Time period, and your DST number. Press " " to
function is ON, your current time should be the decrease number.
Setting range: MAX
time after DST.
+/- 1 hour. Once you
10. Press the " " or " " button to choose the AREA complete the time
setting press SET/RE button.
you live then press SET/RE button to complete
4. press " " or " " to turn on or turn off the device
time setting.
during the sunset time. Then press SET/RE
button to complete the setting.
3. Operating the Time Switch 2. Press the PROGRAM
button once. The display
NORTH
Press the MODE button repeatedly to set the timer will look as shown at the
to Automatic, Random or Manual mode. right. The " ON " in
CENTER
lower right hand corner
NOTE: For the time switch to run programmed indicates that you are now
events, it must be set to "AUTO" mode. programming EVENT 1
SOUTH
which you want your
device turned ON.
• AUTO — runs all events automatically, according
to the schedule you have set. The word "AUTO" 3. Press the SET/RE button to set up the time.
appears in the display. 4. Press the " " or " "
• RDM (Random) - Timer will randomly turn devices display shows the DAY(s) when you want
ON/OFF within15 minutes 5 times per day. This is press SET/RE button.
a security feature in which ON and OFF times The options are:
randomly, creating a more "lived-in" look. • All days of the week (MO TU WE TH FR SA SU)
• Individual days of the week (MO, etc.)
• Weekdays only (MO TU WE TH FR)
• MANUAL (ON or OFF) — turns always ON or OFF
• Weekends only (SA SU)
only when user presses the ON or OFF button.
5. Press the " " or " "
The display is blank, showing neither RDM nor
display shows the HOUR when you want
AUTO.
2-1 press SET/RE button.
• (Astronomic) — Timer will turn devices ON or
6. Press the " " or " "
OFF only during sunrise/sunset time you have set.
display shows the MINUTE when you want
press SET/RE button.
AM
4. Overriding Timer Settings
7. Repeat Steps 3, 4, 5, 6 to set the OFF time for
ON
Event 1.
The ON/OFF buttons
4 SU
ON/OFF override the current
Two kinds of settings can cause the timer to work in
programmed events. To AM
an unexpected way:
override the current
ON
- Set up events in progressive order of time (for
AUTO
program, press the ON/OFF
example, 8:00 pm ON, 9:00 pm ON, 10:00 pm ON
button.
MODE ON/OFF
— NOT 8:00 pm ON, 10:00 pm ON, 9:00 pm ON).
- Do not overlap event times (for example, 8:00 pm
NOTE: If the timer is not in
ON /12:00 pm OFF, and 9:00 pm ON / 11:00 pm
TIME
reset "Manual (ON or OFF)" mode,
3-1 OFF).
it will obey the next programmed event. This allows
PROGRAM SET/RE
MODE
the user to manually turn a light on and allow the
6. Reviewing Events Programmed
program to shut the light back off at a preset time.
TIME
reset
PM 1. In the current time display, press the PROGRAM
ON
button repeatedly to check your settings.
5. Setting Programs
PROGRAM SET/RE
2. When finished, press the TIME button to return
ON/OFF the display to the time of day.
Timer has up to 7 customizable ON/OFF Event
Settings to turn devices on and off at different times
and on different days as programmed.
7. Clearing (Deleting) an Event
MODE 1. Press MODE repeatedly until the display
1. Press the PROGRAM button as many times as
shows AUTO.
necessary to locate the setting you want to clear.
TIME
2. Press and hold the SET/RE for 3 seconds button.
reset
PROGRAM SET/RE
3. When finished, press the TIME button to return WARRANTY
5-2
the display to the time of day.
• For information on product warranty please call
customer service at 1-866-994-4148, 8 a.m. - 6 p.m.,
the
HELPFUL TIPS
EST, Monday - Thursday, 8 a.m. - 5 p.m., EST,
Friday.
• In case of an operational failure of the timer, use a
ON • This product is guaranteed to be free of defects for
paper clip and insert into the RESET hole to clear all
a limited period of one year from the date of
the settings and restart.
purchase.
• If the product suddenly malfunctions and is not
SAFETY INFORMATION damaged by external factors or personal reasons
button repeatedly until the
within the one year warranty limit from the day of
then
Please read and understand this entire manual before
purchase, the product maybe considered for repair.
attempting to assemble, operate or install the product.
If the product is damaged due to natural disaster like
fire, lightning, flood, hurricane, etc., the product will
THIS TIMER IS FOR USE WITH A 125 V AC POWER
not be considered for repair.
SOURCE. 125 V AC / 60 Hz
TROUBLESHOOTING
DO NOT ATTACH A DEVICE THAT EXCEEDS THE
button repeatedly until the
UNIT RATINGS:
then
PROBLEM
15 A / 1,875 Resistive (General Purpose)
8 A / 1,000 W Tungsten (Incandescent)
button repeatedly until the
Timer turns
8.3 A / 996 W Standard Ballast (Fluorescent)
then ON/OFF at
500 VA Ballast (Electronic)
incorrect
1/2 HP (Horsepower Motor) times or
skips some
of the
WARNING
programmed
TO AVOID FIRE, SHOCK, OR DEATH, TURN OFF times.
POWER AT CIRCUIT BREAKER AND TEST THAT
POWER IS OFF BEFORE WIRING.
CAUTION
The attached
• Do not attach a device that exceeds the unit ratings
device turns
as described in the Safety Information section of this
off
manual. immediately
• Wattage of lamps or appliances controlled must NOT after being
turned on.
exceed rated capacity.
• FOR INDOOR USE ONLY.
• Installation by a licensed electrician to local, state LCD screen
is blank.
and national codes is recommended.
• Remove wall plate and make sure both hot and
neutral wires are present in the junction box. If both
LCD screen
wires are not present, additional wiring will be
is on but
necessary before installation can be completed.
attached
• Check that all wire connections are secure.
device is off.
• Place all wires inside junction box. Fit timer into
junction box.
• Reconnect electrical power.
POSSIBLE CORRECTIVE
CAUSE ACTION
1. Programmed 1. Press PROGRAM
event(s) are button to review the
incorrect. settings and revise
2. Timer is in them as necessary.
RANDOM mode, See OPERATING
which varies INSTRUCTIONS.
switching times 2. If you don't want to
up to 15 minutes keep the timer in
(to give your home RANDOM mode,
a "lived-in" look). press MODE to
change to AUTO
mode.
The timer is wired Disconnect wires,
incorrectly. remove timer,
re-install per the
instruction manual. If
problem persists,
contact certified
electrician.
The included Battery will
rechargeable automatically
battery has lost its recharge after
charge. installation.
The light or Make sure the light
attached device or attached device is
itself may be switched ON.
switched OFF.
Printed in China