Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should never be placed near or over a radiator or heat register. This product should not be placed in a built-in installation unless proper ventilation is provided. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 7
Brightness Contrast ratio 300:1 (min) Display color 16.7 million Minimum viewing angle 110° Horizontal (min) 100° Vertical (min) (Contrast ratio>10 at Ta=25°C, 77°F) Response time 25 msec (Typical at 25 degree C) ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 8
Speakers stay on when the rest of the monitor is in power saving. 3.3.3.8 Speakers Impedance 4 Ohm Output Wattage 2W (max.) x 2 3.3.4 Input Signal Connectors 3.3.4.1 Analog RGB Video Input : 15 pin mini D-sub PIN NO. Separate Sync ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 9
RX2- TMDS negative differential input, channel 2 RX2+ TMDS positive differential input, channel 2 Logic Ground Reserved 4 Reserved. No connection Reserved 5 Reserved. No connection DDC-CLK DDC2B Clock DDC-DAT DDC2B Data ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 10
The factory test input video signal is defined as the following table: Preset H.sync V.sync SYNC POL. Video Mode Description Frequency Frequency H-SYNC V-SYNC MOD [1] 31.468 1.0KHz 70.0 1.0Hz 640X350(70) Text mode 31.468 1.0KHz 70.0 1.0Hz MOD [2] 720X400(70) Dos text ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 11
+- 5% tolerance. Item Code Conditions Min. Typ. Max. Unit Contrast (500) White Black at Image Center White Whole White (300) cd / m 2 Brightness VMAX ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 12
Warm Up time: minimum 30 minutes Measuring instrument: TOPCOM BM-7 Luminance Meter Measuring distance: 500 mm Measuring angle: 2° 500mm BM-7 2 Degree Notes: (Note 1) Contrast ratio is defined as the following formula. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 13
Wh it e(TF T OF F ) Wh it e Opt ica l Respon se (Note 4) Judge points for brightness uniformity Brightness uniformity is judged at five (9) points on display area: ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 16
7.1 OSD Brightness 100%(based on 0-100%) Contrast 80%(based on 0-100%) AutoTune Executed Color Temperature 6500k Volume Balance Bass/Treble OSD Timeout 15 Sec Language English OSD position Center Scaling Fill all 7.2 Power Switch ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 17
Preset Signal Timings H-Video H active Horizontal H front H back H pulse H total V-Video V active Vertical V front V back V pulse V total ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Submenu. For details on the controls, please follow the steps listed below. Note: Any OSD setting will only save after user totally exit OSD menu. 1. Press the [1] button to display the Main Menu shown below. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 25
[2] to toggle between brightness and contrast. C o n t r a s t 1 : E x i t 2 : B r i g h t n e s s ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 26
1 : Exit 2 : Select Volume [ ] increases the volume, [ ] decreases the volume. V o lu m e : E x i t : S e l e c t ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 27
: E x i t : S e l e c t Mute M u t e O f f : E x i t : S e l e c t ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 28
User color—Individual adjustments for fed (R), green (G), blue (B). 1 To adjust selected color, press ] or [ ]. 2 Press button [2] to set adjustment and select next color to adjust. User Color Green Blue 1: Exit 2: Select ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
] move screen image down, [ ] moves screen image up. V - P o s it io n 1 : E x i t 2 : S e l e c t ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
: E x i t : S e l e c t Setup Menu Setup Menu Language Resolution Notice OSD Position OSD Timeout OSD Background Touch Tone 1 : Exit 2 : Select ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 31
OSD V-Position ] moves OSD down, [ ] moves the OSD up. O S D V -P o s itio n 1 : E x it 2 : S e le c t ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 32
* These functions are not available in Digital Mode. Memory Recall is to recall the following functions to factory setting: Contrast, Brightness, H Size, H/V Position, Color Temperature @ 6500K, OSD Position, Sharpness, & OSD Timeout. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 33
OSD Auto Save The OSD shall save new settings when it is turned off by the user or when it times out. There shall not be a separate save. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
LOW signal from key button.) Pin13, 14 communicate with ICM9 (EEPROM) by I Pin17, 18,20,21,22,23 communicate with ICM11 (scalar) by 6-wire protocol Pin19 detect audio in Pin28, 29 do ISP (in-system program) ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 35
(2) TMDS Differential Input Clock (RC+ and RC-) (3) Video Clock (VCLK) input pin (4) Host Interface Transfer Clock (HCLK for 6-Wire nibble; SCL for 2-wire serial) ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 36
SDA output pin is used as serial data line the SCL pin will hold high. The DDC2B node (BI-directional mode) BUS consists of two wires. SCL is for the data transmission clock and SDA is for the data line. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Gain output& input selector for left channel Bin _L Left bass controller input channel Bout _L Left bass controller output channel Bin _R Right bass controller input channel Bout _R Right bass controller output channel ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 38
It is designed specifically for human interfaces, like control panels, application lighting controls or anywhere a mechanical switch or button may be found. The device is designed to detect touch on up to 8 point independently. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 39
As a value of this resistor, internal circuit decide time delay between input and TTL output. P_on_rst Prevent abnormal operation during VDD on transient time. EN_x (No) Select input channel and control of sensitivity. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Check that CM16 positive is at 5V. (FIG 2.) Check that the voltage level of JM1 is approximately 12V check Check JM2 pin1 ICM1 failure LM1 failure Adapter failure is12V, pin5 is 5V Inverter failure ICM10 failure ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 44
5V Failure point Check ICM11 Pin4is low voltage 1.ICM15, ICM16 failure 2.ICM11 failure Inverter failure ICM10 failure Check ICM11 ICM10 failure Pin5, 6, 7, and 8 is About 3.3V ICM17 failure ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Check that ICM2 Failure point Pin5, 6, 7, and 8 is LM1 failure Check that LM5 Failure point pin 2 is about 5V ICM2 failure Failure point 1.LM5 failure 2.DM1 failure 3.ICM1 failure ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 46
Check ICA3 pin4, 6 is FIG20. 1.ICA1 failure 2.ICM10 failure Check ICA5, ICA6 pin4 is Failure point about 5V 1. QA6 or QA7 failure 2. ICA3 failure ICA5 or ICA6 failure ICM10 failure ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 47
Check the signal level of RM9, RM10, RM11 is FIG 5. Check the HS and VS is Failure point FIG 6. and FIG 7. 1.The video connector is disconnected 2.Signal cable disconnected ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 48
6. Keypad cannot work Check that the signal cable is fully connected between the Inverter and touch board Failure point Failure point 1. ICT1 failure The cable is disconnected 2. LED failure ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
2: Select Otherwise, follow the procedure. Described in session 1.4.1 to enter the factory mode again. 1.4.3 Under factory mode, press “ 1” Key. The monitor will exit factory mode and under ordinary ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
2.1.2 Use “2” to move cursor to R-driver or G-driver or B-driver and then press “UP” or “DOWN” key to adjust it to meet following chromaticity spec. 9300 K x = 0.283 0.030 , y = 0.298 0.030 Y>= 160CD/M ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...
Page 51
When exit factor mode OSD menu, the above result R.G.B gain will automatically be saved. 3. Factory preset setting 3.1 In factory mode OSD main menu, select factory default setting. Press “2” to confirm the selection. ViewSonic Corporation VX500+-1 Confidential – Do Not Copy...