Subscribe to Our Youtube Channel
Related Manuals for CCTV PTA1215X
Summary of Contents for CCTV PTA1215X
- Page 1 User's Manual IR Intelligent Ball Video Camera ……Please read the manual carefully prior to installation of the device ……...
- Page 2 Notes for attention Important safety precaution 1. Please read the manual carefully prior to operation. 2. Please refer to the instructions for all operations. 3. Do not put the device on an unstable desktop or rack. 4. Do not put any foreign matter or fluid into the device to prevent from damaging the device.
-
Page 3: Table Of Contents
Table of Contents Chapter I Overview of the product …………………………………………… 4 1.1 A brief introduction to the product …………………………………………… 4 1.2 Technical specification ……………………………………………………… 4 1.3 Description of functions ……………………………………………………… 5 Chapter II Installation of the product………………………………………… 8 2．1 Setting of DIP switch of ball camera ……………………………………… 9 2．... -
Page 4: Chapter I Overview Of The Product
Chapter I Overview of the product 1.1 A brief introduction to the product IR intelligent high speed ball camera is a high performance digital signal processing (DSP) camera equipped with a zoom lens, and it is a hi-tech monitoring product incorporating a universal speed change PTZ unit and a digital decoder. Used for free and rapid positioning and continuous tracking scanning, it achieves all-round monitoring without dead zone in the real sense. - Page 5 Automatic reversing It can reverse for 180º when it is vertical to the function ground. Automatic control of Control speed can be adjusted automatically in zoom speed according to zoom length Two-point scanning 355º can be set Two-point scanning Level 1-64 can be set speed Retention time for 1-60 seconds can be set...
-
Page 6: Description Of Functions
1.3 Description of functions Main functions of IR intelligent high-speed ball camera are introduced briefly as follows: 1. Setting of address code, baud rate and control protocol Any operation command has address code, baud rate and control protocol of its target in the camera, and a separate camera only responds to the operation command conforming to its own address code, baud rate and control protocol. - Page 7 state in the memory, and they can be invoked rapidly when they are in need to adjust PTZ unit and camera to the position. The operator can save and invoke preset points through control equipment such as control keyboard and IR controller conveniently and rapidly.
- Page 8 can perform luminance compensation for a darker object automatically on a highlighted background, perform lighting adjustment for the highlighted background, prevent from a glare in the whole picture due to brightness of the background, and the target cannot be differentiated due to darkness, and acquire a clear image. 9.
-
Page 9: Chapter Ii Installation Of The Product
a certain interval and speed horizontally. 15. Regional scanning Only an external command or invoking through power-on action, idle action and alarm interlinking is required to make the ball camera scan in a circulating way at a certain speed and in the specified range horizontally. Chapter II Installation of the product 2．1 Setting of DIP switch of ball camera (1) DIP switch... - Page 10 (3) Baud rate setting (SW1) DIP Switch 2400 bps 4800 bps 9600 bps 19200 bps Bit 5 Bit 6 Bit 7 Protocol selector switch Bit 8 Rs485 terminal (4) Protocol setting (SW1) Setup list of protocol DIP switch Switch Setup Switch Setup Switch Setup Switch Setup...
-
Page 11: 2． 2． 1 Operations Of Ball Camera
¤ Video recorder/rotation automatic matching off ¤ Horizontal slow scanning ¤ Horizontal fast scanning ¤ Set guard bit ¤ Enable guard bit ¤ Stop guard bit ¤ Start up the first track record (valid only for menu machine type) ¤ Start up the second track record (valid only for menu machine type) ¤... - Page 12 After power of the ball camera is on, the camera moves horizontally and vertically automatically first, then pulls the lens to the nearest place, to the farthest place, and stops after movement is over. Confirm the ball camera operates normally through self-check.
-
Page 13: Figure Of Actual Object
2．2．1Figure of actual object 3-2 Figure 3-2 2．2．2 Dimensional diagram of rack 3-3 Figure 3-3 2．2．3 Installation of rack and ball camera Step 1 Installation of rack... -
Page 14: Chapter Ⅲtroubleshooting
Figure 3-4 Determine position of screw installation hole Figure 3-5 Drill holes on the installation positions Figure 3-6 Drill holes required for installation Figure 3-7 Tighten fixing screws Determine installation positions on the wall to mount the ball camera, draw hole positions on the wall with a signal pen in accordance with positions of screw holes of the rack, as shown in figure 3-5. - Page 15 power-on but out of Wrong setting of PTZ address code or Set the address or Baud control Baud rate rate again Unmatched protocol Select correct protocol Reverse connection or open circuit of Check connection Rs485 line RS485 control line Mechanical failure Check and repair Image displayed with tweet from motor and...
Need help?
Do you have a question about the PTA1215X and is the answer not in the manual?
Questions and answers