Related Manuals for CCTV JE900BN
Summary of Contents for CCTV JE900BN
- Page 1 User’s Manual for Smart Constant Speed Dome Camera Please read the manual carefully before installing and using the unit. Model: JE900BN, JE900BNC...
-
Page 2: Table Of Contents
Table of Contents PART I: INTRODUCTION ..........................2 1-1 I :................2 NSTRUCTIONS 1-2 C ..............2 HARACTERISTICS 1-3 M ............3 ECHNICAL Electric Index ............................3 Mechanical Index ..........................3 Ambient Index............................. 3 Camera Index ............................. 4 1-4 S ..4 TYLES OF NSTALLATION AND NCILLARY OMPONENTS... -
Page 3: Part I: Introduction
Part I: Introduction 1-1 Instructions: We greatly appreciate your choosing our product! The product is under one year warranty, including free maintenance or spare parts replacement. Do not dismantle and repair the unit without the company’s authorization. Damage or breakdown arising from the following circumstances is No free maintenance: 1. -
Page 4: Main Technical Data
can be adjusted according to actual conditions. 8. The built-in PCB panel supports multi mainstream protocols, which can be input according to the customer’s needs. The Baud rate is also adjustable. 9. The unit adopts DC14V(15V) power supply and separates from it the components that produce heat in the process of transformation, which prolongs the durability of the unit. -
Page 5: Camera Index
4. Camera Index Image Sensor 1/4〞Super Had CCD Resolution. 480TV Line Lens f=3.25-88mm High Durability 27X Zoom Lens Angle of View 48 degrees (w) Horizontal 3 degrees (t) Sync System Internal/Line Lock NTSC 60 Hz , PAL 50HzC Minimum illumination 0.5Lux/0.1Lux with B/W mode IR Sensitive 0Lux with IR on... -
Page 6: Installation Of Camera Block
2. Dimensions for embedded Dome Camera 2-2 Installation of Camera block 1. Firstly make sure the size of the selected video camera is within the acceptable range Then follow the direction indicated on the camera suspender, and fix the camera to it with special screws. -
Page 7: Connection Of The Camera And The Housing
(D1=D2). (Refer to the figure below.) Observe if there is any collision or friction between the camera and the vitreous cover. If there is any, adjust the camera. 2. Connect Lens Controlling Cable Camera Lens Controlling Cable should be provided by the camera supporter. Connect the camera controlling cable well according to the corresponding relationship between the camera and the outlet of PCB panel shown in the following table. - Page 8 Step 1 Push the connecting ports end of the power, video and controlling integrated cable through the central hole of the peg-board, and then fix the connecting ports into the socket on the module. Then fit the parts shown with dotted lines on the module into the indentation shown with dotted lines on the peg-board.
-
Page 9: Installation Of Dome Cover
Step 3 After the module is in right position, tighten the special screw (the screw will not drop even when it is loosed to the end) manually or with a screwdriver. Be sure the screw is tight, otherwise, the module might fall when the unit is running. Installation of the camera completed. -
Page 10: Housing And Wall-Mount Bracket Installation
2-5 For embedded dome camera Fit the three plastic pegs on the dome cover to the corresponding ones on the housing, then turn it to the right for about 20 degrees till it stops moving. (See the above figure) 2-5 Housing and Wall-mount Bracket installation Push the power, video and controlling integrated cable through the bracket hole, then direct the top of the housing to the bracket hole and tighten them. -
Page 11: Installation Of The Bracket
above figure) 2-6 Installation of the Bracket a. Wall-mount installation Figure 1: Dimension of the installing bottom board of the Wall Bracket for Outdoor Dome Camera Select the where you want to installing and make sure the place can be sustained its weight. -
Page 12: Power Supply Adapter Installation
1. The diameter of the flange on the outdoor vertical pole should be at least 20cm more than that of the installing flange of the Pole bracket. 2. The cable should not go through the cable-slot on the flange edge of the Pole bracket, it should go through the central hole of the bracket. -
Page 13: Installation For Embedded Dome Camera
2-8 Installation for Embedded dome Camera Locations with suspended top suit the dome camera with in-ceiling installation style, which appears to be a hemisphere, having elegant-look and good concealment. The in-ceiling style installation applies to solid locations of the ceiling. First, select the desired location, pencil the outline of the upper housing on the ceiling and make a corresponding-size bore(about 210mm diameters for Seven-inch Dome Camera, about 240mm diameters for Nine-inch one), then insert the upper housing into the ceiling, and... - Page 14 controlling cable with the 485 port of the module, the green for 485+ while the white for 485-. 3. Connection of the Cable for Temperature Controlling Devices If the selected product has temperature controlling device, two kinds of power supply is acceptable: DC14V (15V). Users can choose according to the condition.
-
Page 15: Part Iii: Setup And Operate
Part III: Setup and Operate 3-1 Protocol, Baud Rate, Address and Speed setup It is important to setup the protocol, baud rate and camera address for controlling, Both of the dome camera and controller must be setting same in the protocol, baud rate and camera address... - Page 16 1. Address Setup As shown in the figure below, DIP-1 to DIP-6 of the 8-button coding switches is used to set up address of the dome camera from 1 to 63. Control can be realized only when address code of the dome camera is identical to that of the hard disk video recorder or matrix or controlling keyboard.
-
Page 17: Running State Test While The Camera Power On
DIP- 4,3,2,1 Types of Protocols 0 0 0 0 PELCO_D 0 0 0 1 PELCO_P 1 1 1 0 1 1 1 1 PELCO_D1 Table 5: Correspondence of Coding Switches and Protocols. 4. Set up the Movement Speed The movement speed of the dome can be set up through the coding switch. DIP 5 and DIP6 of the 6-button coding switch (see figure above) are used to set up the movement speed of the dome. -
Page 18: The Particular Command And Its Definition
As per the method introduced above, adjust the unit well. 3-3 The particular command and its Definition The below table is the particular short command for operate the PTZ camera with protocol “Pelco-D” and “Pelco-P” These short commands are important for operation the PTZ function. Please remember Code No. - Page 19 such devices as controlling keyboard to save and preview preset positions fast and conveniently. The dome camera can support 16 preset positions. A. Set up preset positions After controlling (pan/tilt) the dome camera to the position you want to monitor keyboard, enter the number for representing the preset position and press the “PRESET”...
-
Page 20: Setup And Running Of Tour Group
3-5 Setup and running of Tour group Automatic tour function is a latest function of the constant-speed dome camera. The user can program the preset positions into the automatic tour in the required order, when necessary, run the tour, the constant-speed dome camera will automatically scan the preset positions set in the tour consecutively and circularly. -
Page 21: Setup And Scan Between Two Points
6. Enter number “4”and key “PREVIEW”, the position “4” is added in the tour group as fifth tour position 7. Enter number “6”and key “PREVIEW”, the position “6” is added in the tour group as sixth tour position 8. Enter number “141”(111) and key “PREVIEW” to exit tour setup) 9. -
Page 22: Start Scanning Between Two Points
3.6.2 Start scanning between two points a. Enter 132(102) and press “PREVIEW” key b. Press “AUTO” key 3-7 Start 360° scanning function of the Pan/Tilt The Camera can be 360° endless horizontal scanning. The operation is as below: 3-8 Stop the auto scanning While the camera is carrying out auto scanning, if you want to stop the auto scanning, you can enter 138 (108) and press “PREVIEW”... -
Page 23: Part Iv: Appendix
Part IV: Appendix Simple troubles and corresponding solutions Problems Possible causes Soluition Wrong connection of power cables Correct No action, no picture, indicator not Power supply damaged Replace on when power is switched on. Not required power type Replace Bad power cable connection Correct Address or Baud rate setup wrong Set up again...