Related Manuals for LaserLine 290i2
Summary of Contents for LaserLine 290i2
- Page 1 290i2/212/291/213 INSURANCE APPROVED ALARM/IMMOBILISER USER GUIDE ® C A R A L A R M S Y S T E M S ISUT291-213UK.p65 11/05/2006, 18.53...
- Page 2 290i2/212, as evaluated by Thatcham (MIRRC). Note: Category 2 à 1 (L2 à 1) product – 290i2/212 alarm system is only to be fitted in conjunc- tion with a Category 2 (L2) immobiliser to obtain Category 1 status for the vehicle security.
- Page 3 You would have received from your installer, two remote controls (see fig. 1) and have been shown the location of the Status LED (fig. 2). FUNCTIONS Button A: arming/disarming of the alarm (290i2/ 212); Button A: arming/disarming of the alarm and immobiliser (291/213);...
-
Page 4: Alarm Condition
DISARMING THE ALARM SYSTEM Press button A (arm/disarm), located on the right of the remote control (see fig. 1). The direction indicator lights will flash once and the alarm may give one audible tone (programmable function) generated at the same time to indicate that the alarm system has been disarmed. The power locks* will open and, if button C is activated, all the courtesy lights will turn on for 10 seconds. - Page 5 BUTTON ‘B’ FUNCTIONS (Panic and Excluding the ultrasonic sensors and electric power window* module) Panic function: Pressing this button twice within a maximum of 3 seconds activates the siren for 10 seconds and the additional siren*. To stop the sound prior to the 10 seconds, press button ‘B’ on the remote control.
-
Page 6: How To Know Your Emergency Pin Code
DISARMING USING THE EMERGENCY PIN CODE (290i2/212 Only) This function only applies if there is no optional electronic key. If all the remote controls have been lost or are malfunctioning, you can disarm the alarm system using the “emergency pin code”. - Page 7 HOW TO DISARM THE ALARM USING THE EMERGENCY PIN CODE If your transmitter does not work correctly or has been lost, to disarm the alarm system you must insert the “emergency pin code” by doing the following: With the alarm armed, activate the siren by opening the door on the driver’s side; Enter the vehicle.
- Page 8 If the code inserted is correct, the alarm will automatically DISARM without any audible tones and visual signals. If the code is incorrect, an alarm condition will occur. ALARM ARMING/DISARMING USING THE ELECTRONIC KEY (Optional on 290i2/212) fig. 3 fig. 4 ARMING THE ALARM SYSTEM The alarm system can also be armed using the electronic key (See fig.
-
Page 9: Sensor Self-Testing
then will begin flashing in a regular pattern. Activating the system with the electronic key disables the SENSOR SELF-TESTING functions (see the SENSOR SELF-TESTING paragraph). DISARMING THE ALARM SYSTEM If the alarm system was previously armed using the electronic key, you will have 10 seconds to enter the vehicle before an alarm condition occurs. - Page 10 GARAGE sensor generated an alarm condition* 9 FLASHES/PAUSE: FLAT REMOTE CONTROL BATTERY 10 FLASHES/PAUSE: FLAT INTERNAL BATTERY AUTO-POWER SUPPLY (290i2/291 only) Attention: Ø The causes of the alarm will be displayed in sequence from the last to the fifth. At the end of the display, to repeat the five codes press both buttons again on the remote control.
-
Page 11: Problem Solving
Ø The memory of the last five alarm conditions will be cleared when the alarm power supply is disconnected. PROBLEM SOLVING If your alarm sounds for no apparent reason, please refer to the DIAGNOSTICS FLASH CODES for possible condition. Possible causes of the alarm condition could be: Vehicle has been tampered with. -
Page 12: Comfort Function
courtesy lights or the external sidelights, illuminating the area near the car. Pressing button “C” again prior to the 10 seconds causes the lighting to switch off (vehicle with courtesy lights delay system may take longer to switch off). COMFORT FUNCTION* (only for vehicle equipped with Comfort Closing of locking/ windows/roof**) For cars equipped with Comfort Closing function, the windows can be closed just by pressing and holding button ‘A’... - Page 13 (inertia switch) power locking system that is activated if an accident occurs. If not, a similar one available on the market must be installed. Laserline S.p.A. will be not be held responsible if users do not comply with this note.
- Page 14 To complete the auto-learning procedure either; turn the ignition ON to exit the function (291)or wait 10 seconds (290i2) for the LED to go out and then start to flash the emergency pin code (see the How to Know Your Emergency Pin Code paragraph).
-
Page 15: Battery Replacement
REMOTE CONTROL SPECIAL FEATURE FLAT REMOTE CONTROL BATTERY SIGNAL By using the “ALARM AUTO-DIAGNOSTICS” function, tells you that the remote control battery is almost dead. When the alarm memory is checked, the LED on the dashboard will flash 9 times. This means that the alarm has detected that the remote control battery is almost dead. -
Page 16: Technical Data
TECHNICAL DATA 290i2/212 POWER SUPPLY .................... 9-15V negative ground CURRENT ABSORBED WITH ALARM ARMED (with ultrasonic) ..........<13 mA CURRENT ABSORBED WITH ALARM DISARMED (with ultrasonic) ..........<5 mA PRE-ALARM TIME ........................30 sec. PRE-ALARM TIME (armed using electronic key) ............... 30 sec. - Page 17 (petrol, oil, detergents, etc.) 290i2/212 TEST APPROVAL NUMBERS 290i2 - MIRRC Reference Number: Category 2 - 1 TU2 - 1183/1100 290i2 -MIRRC Reference Number: Category L2 - 1 TUL - 45/1200 212 - MIRRC Reference Number: Category 2 - 1 TU2-1368/0506...
-
Page 18: Lifetime Warranty
LIFETIME WARRANTY Product warranty covers units to be free from defects in manufacture for the lifetime ownership of the original vehicle, in accordance with the terms and conditions of this warranty document. Any product, which is deemed to be defective, will be replaced or repaired. Accessories including remote controls, touch keys and additional modules are guaranteed for a period of 12 months from date of installation. -
Page 19: Exclusions From Warranty
NOTE Manufacturer declines any responsibility for damage of the alarm/immobiliser and the vehicle electrical system due to WRONG INSTALLATION OR TAMPERING. LASERLINE SpA RESERVES THE RIGHT TO EFFECT CHANGES OF THE PRODUCT WITHOUT FURTHER NOTICE. ISUT291-213UK.p65 11/05/2006, 18.53... - Page 20 Service Inspection 2 YRS 3 YRS 1 YRS 4 YRS Installer’s Stamp Installer’s Stamp Installer’s Stamp Installer’s Stamp Cert. No. Cert. No. Cert. No. Cert. No. Reg. No. Reg. No. Reg. No. Reg. No. Date. Date. Date. Date. Signature Signature Signature Signature 5 YRS...
- Page 21 CUSTOMER LIFETIME WARRANTY REGISTRATION Alarm/Immobiliser Model No. ………...…………….....Make………………………....……. Accessories Fitted …………………………......Model………………….....…… Date of Installation……………………………….....Reg.No. ……….…..………..……. Customer Name………………………………......Year of Manufacture…………....Address………………………………......………………………………....……………................................... Postcode ………………………......…...Tel No....……….....…………… Installer Name …………………..……………..Account No. …....……………..…….. Address…………………………………………………………………………………..………………... Postcode ……………………………………………..Tel No. ……....…....………… I have read and understood the terms and conditions of the Customer Lifetime Warranty. Customer Signature...............
- Page 22 Return to: Laserline Direct Limited 33, Craven Court Winwick Quay Warrington Cheshire WA2 8QU ISUT291-213UK.p65 11/05/2006, 18.53...
- Page 23 ISUT291-213UK.p65 11/05/2006, 18.53...
- Page 24 Dealer Stamp Our commissioned Sales and Support Agents in the UK are Laserline Direct Limited 33, Craven Court - Winwick Quay - Warrington - Cheshire WA2 8QU cod. ISUT291-213UK FILENAME: ISUT291-213UK.P65 ISUT291-213UK.p65 11/05/2006, 18.53...