Page 1
TE 7-A Operating instructions Mode d’emploi Manual de instrucciones Manual de instruções Printed: 07.07.2013 | Doc-Nr: PUB / 5142505 / 000 / 00...
Page 2
36 Volt This Product is Certified Ce produit est certifié Este producto esta certificado Este produto está certificado 36 Volt Li-Ion 3.3 Ah Printed: 07.07.2013 | Doc-Nr: PUB / 5142505 / 000 / 00...
In these operating instructions, the designation “the Always keep these operating instructions to- power tool” always refers to the TE 7-A cordless rotary gether with the power tool. hammer. Ensure that the operating instructions are...
Do not use the battery as a power source for other unspecified appliances. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
Page 8
Power tool TE‑C CLICK chuck Side handle with depth gauge Operating instructions Hilti toolbox or cardboard box Cleaning cloth Grease 2.9 Additional items required for operating the tool One B 36/2.4 NiCd battery with C 7/36‑ACS charger or one B 36/3.3 Li‑Ion battery with C4⁄36‑90 or C4⁄36‑350 charger, or one B 36/3.9 Li‑Ion battery with C 4/36‑ACS charger.
3 Insert tools, accessories Insert tools and accessories for the TE 7‑A Designation Description Hammer drill bits ∅ 5…28 mm (³/₁₆" to 1") Forming and installation drill bits ∅ 5…20 mm (³/₁₆" to ¾") Lightweight percussion core bits ∅ 25…68 mm (1" to 2½") Multipurpose hole saws ∅...
Other information about the power tool Chuck TE‑C Click Battery B 36/2.4 NiCd B 36/3.3 Li‑Ion B 36/3.9 Li‑Ion Rated voltage 36 V 36 V 36 V Capacity 2.4 Ah 3.3 Ah 3.9 Ah Energy capacity 86.4 Wh 118.8 Wh 140.4 Wh Weight 2.1 kg (4.63 lb)
Page 11
e) Do not overreach. Keep proper footing and bal- d) Under abusive conditions, liquid may be ejected ance at all times. This enables better control of the from the battery, avoid contact. If contact acci- dentally occurs, flush with water. If liquid contacts power tool in unexpected situations.
5.3.6 Personal protective equipment Contact Hilti Service after the battery has been allowed to cool. 5.3.4 Electrical safety Before beginning work, check the working area (e.g.
6.7 Use of the belt adapter (forward/reverse switch in the middle position). Use only NOTE the Hilti batteries approved for use with this power tool. The working weight of the power tool can be reduced by fitting an accessory belt adapter. The battery cannot be Push the battery into the power tool from the rear charged by way of the belt adapter.
Page 14
Set the forward / reverse switch to the middle posi- Set the forward / reverse switch to the middle posi- tion or remove the battery from the power tool. tion or remove the battery from the power tool. Check that the connection end of the insert tool is Grip the chuck sleeve, pull it forward and hold it clean and lightly greased.
Fit the battery. 7.2.4.3 Chiseling 13 Position the power tool and drill bit at the point Fit the battery. where the hole is to be drilled. NOTE Do not operate the function selector switch Press the control switch slowly (drill at a low speed while the motor is running.
This may negatively affect the electrical safety of the power tool. Charge the battery with the Hilti charger approved for use with Li-ion batteries. NOTE 8.3 Cleaning or replacing the dust shield...
Dispose of defective batteries without delay. Keep them out of reach of children. Do not attempt to open or dismantle batteries and do not dispose of them by incineration. CAUTION Dispose of the batteries in accordance with national regulations or return them to Hilti.
Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.