Hilti TE 7 Operating Instructions Manual
  1. Manuals
  2. Brands
  3. Hilti Manuals
  4. Rotary Hammer
  5. TE 7
  6. Operating instructions manual

Hilti TE 7 Operating Instructions Manual

Rotary hammer
Hide thumbs Also See for TE 7:
Table of Contents

Advertisement

Quick Links

See also: Operating Instructions , Operating Instructions Manual
TE 7
Bedienungsanleitung
Operating instructions
Mode d'emploi
de
en
fr

Advertisement

Table of Contents
loading

Related Manuals for Hilti TE 7

Summary of Contents for Hilti TE 7

  • Page 1 TE 7 Bedienungsanleitung Operating instructions Mode d’emploi...

  • Page 5: Table Of Contents

    In these operating instructions, the designation “the Always keep these operating instructions power tool” always refers to the TE 7 rotary hammer. together with the power tool. Operating controls and parts 1 Ensure that the operating instructions are...

  • Page 6: Description

    Changes or modifications to the power tool are not permissible. To avoid the risk of injury, use only genuine Hilti accessories and insert tools. Observe the information printed in the operating instructions concerning operation, care and maintenance.
  • Page 7 1 Power tool 1 TE‑C CLICK chuck 1 Side handle with depth gauge 1 Operating instructions 1 Hilti toolbox 1 Cleaning cloth 1 Grease 2.8 Using extension cords Use only extension cords of a type approved for the application and with conductors of adequate cross section.

  • Page 8: Insert Tools, Accessories

    2.10 Using a generator or transformer This power tool may be powered by a generator or transformer which fulfills the following conditions: The unit must provide a power output in watts of at least twice the value printed on the type identification plate on the power tool.

  • Page 9: Safety Instructions

    Power tool TE 7 Weight in accordance with EPTA procedure 01/2003 2.9 kg Dimensions (L x W x H) 320 mm x 75 mm x 215 mm Speed under no load 0…1,050/min Hammer drilling speed 860/min Single impact energy in accordance with EPTA 1.8 J...
  • Page 10 liquids, gases or dust. Power tools create sparks d) Remove any adjusting key or wrench before which may ignite the dust or fumes. turning the power tool on. A wrench or a key left c) Keep children and bystanders away while oper- attached to a rotating part of the power tool may ating a power tool.
  • Page 11 Wear ear protectors. Exposure to noise can cause collection, use a suitable vacuum cleaner of the hearing loss. type recommended by Hilti for wood dust and/or b) Use auxiliary handle(s), if supplied with the mineral dust together with this tool. Ensure that tool.

  • Page 12: Before Use

    Hilti Service Center. Under unfavorable cir- 5.2.5 Personal protective equipment cumstances, dampness or dust adhering to the surface of the power tool, especially dust from conductive materials, may present a risk of elec- tric shock.

  • Page 13: Operation

    7. Operation Push the insert tool further into the chuck until it is heard to engage. Check that the insert tool has engaged correctly by pulling it. 7.1.3 Removing the insert tool 5 CAUTION In the event of the drill bit sticking, the power tool CAUTION will pivot about its own axis.

  • Page 14: Care And Maintenance

    Position the power tool and drill bit at the point 7.2 Operation where the hole is to be drilled. Press the control switch slowly (drill at a low speed until the drill bit centers itself in the hole). Press the control switch fully to continue drilling with full power.

  • Page 15: Troubleshooting

    Clean the sealing lip by wiping it carefully and then grease it again lightly 8.5 Checking the power tool after care and with Hilti grease. It is essential that the dust shield maintenance is replaced if the sealing lip is found to be damaged.

  • Page 16: Disposal

    10. Disposal Most of the materials from which Hilti power tools or appliances are manufactured can be recycled. The materials must be correctly separated before they can be recycled. In many countries, Hilti has already made arrangements for taking back your old power tools or appliances for recycling. Please ask your Hilti customer service department or Hilti representative for further information.

  • Page 17: Ec Declaration Of Conformity

    This constitutes Hilti’s entire obligation with regard concerning warranties. to warranty and supersedes all prior or contempor- 12. EC declaration of conformity Hilti Corporation Designation: Rotary hammer Type: TE 7 Year of design:...
  • Page 18 Fax: +423 / 234 29 65 www.hilti.com 428555 / A Hilti = registered trademark of Hilti Corp., Schaan W 3786 0310 00-Pos. 1 1 Printed in Liechtenstein © 2010 Right of technical and programme changes reserved S. E. & O.

Table of Contents