Jede QUATTRO Service Manual
  1. Manuals
  2. Brands
  3. Jede Manuals
  4. Coffee Maker
  5. QUATTRO
  6. Service manual

Jede QUATTRO Service Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

QUATTRO
SERVICE MANUAL
English - GB

Advertisement

Table of Contents
loading

Related Manuals for Jede QUATTRO

Summary of Contents for Jede QUATTRO

  • Page 1 QUATTRO SERVICE MANUAL English - GB...

  • Page 2: Table Of Contents

    QUATTRO Contents Important information 1.1 Safety 1.2 This user instruction 1.3 Type plate 1.4 Disposal Symbols Description of the machine 3.1 Quattro 3.2 Cartridge system 3.3 Drinks 3.4 Serving Description of the front of the machine 3.6 Description of the back of the machine 3.7 Description of the inside of the machine 3.8 Placement of the vending machine Installation and start-up 4.1 Installation and start-up, direct connection to a mains water supply 4.2 Installation and start-up, built in manual fill water tank 4.3...
  • Page 3 QUATTRO Removing the vending machine from service 8.1 Transport Technical data Service Warranty Energy saving function Notes Front Casing Base cover Mixer system Tank module Tank complete unit Serving module JM Dispenser Motor unit 23. Manual fill cold water tank Wiring diagram 230 V...

  • Page 4: Important Information

    QUATTRO . Important information Thank you for choosing an automatic vending machine from Jede. Before the machine is put into service, read this manual carefully. This is important so that installation and use can be carried out in a safe manner and a prerequisite for the warranty terms applying. Information in this manual can be changed without prior notice. Store this user manual in a safe place for future use. This user manual may not be copied, used or translated, either wholly or partly without written consent from Jede AB except in accordance with copyright laws. An updated manual when available is found via the following link: www.jede.com . Safety • The vending machine may only be used with Jede’s drink cartridges. • For safety reasons, repairs may only be carried out by trained personnel on Jede equipment, repairs carried out by non trained personal can involve risks to the user and cause the warranty to become invalid. • Only original parts may be used for any repairs. • Note that the heater tank inside the machine contains hot water and can cause burns if touched or if the machine is used incorrectly. • The vending machine may only be connected to a protective earthed socket via the attached mains cable. • The machine must be connected via an earth fault breaker. • The machine is only voltage-free when the plug is removed from the wall socket or the mains cable from the back of the machine. • In case the machine is directly connected to a mains water supply, regulary check the hose for wear damage, cracks or other defects. By replacing it in time, you can prevent water damage. • Before the automatic machine is transported, moved or stored for a long period of time, its tanks must be emptied from all water.

  • Page 5: This User Instruction

    QUATTRO .2 This user instruction The contents in this user instruction describe the vending machine’s function and operation, as well as instructions for installation and maintenance. .3 Type plate The machine’s type plate with its serial number is placed on the back of the machine. Figure 1 .4 Disposal This product may not be discarded among household waste when its lifespan has ended. The machine contains electronics, plastic and metal. Sort it and recycle the material. Contact either the reseller where you purchased the machine or your local municipality for information on how you can best dispose of the product in an environmentally adapted manner. If the machine is replaced by a new one, the Jede machine supplier may take back the old machine. If so, they will ensure the machine is recy- cled in a responsible manner. (Please check your country regulations in regard to this). All plastic material is type marked for easier sorting. 2. Symbols This symbol states that there is hazardous current in the machine, which involves the risk for electric shocks and severe personal injury. This symbol marks important instructions and tips concerning the machine’s operation and care. Rev. A Service manual 2012-09-10...

  • Page 6: Description Of The Machine

    QUATTRO 3. Description of the machine 3. Quattro Quattro is a new addition to Jede’s machine product range for drink cartridges. The machine is prepared for both fixed connection to a mains water supply (see chapter 4.1) and a water supply via its built-in tank (see chapter 4.2). The type of water connection is automatically detected upon start-up (see chapter 4). 3.2 Cartridge system The machine is constructed for four drink cartridges, which are easy to change ac- cording to consumption. The cartridges are accessible when the vending machine’s front is lifted up and folded upward (see chapter 4.3) 3.3 Drinks The machine is programmed with 3 different loading schedules for varying drink volumes and flavours (see chapter 5). It is also possible to temporarily vary the flavour of the drinks by holding in the drink button while serving (see chapter 5.3). 3.4 Serving The vending machine serves 4 different coffee drinks, hot chocolate and tea water. The cup of your choice can be used with a max. height of 110 mm. Drinks are pre- pared in separate mixer bowls and whippers (see chapter 6). 1. Front. 2. Drink cartridge. 3. Water tank, cap. 4. Mixing bowl. Figure 2 Service manual Rev. A 2012-09-10...

  • Page 7: Description Of The Front Of The Machine

    QUATTRO 3.5 Description of the front of the machine Figure 3 1. Red LED, indicates start-up and error status. 2. Green LED, indicates normal function. 3. Lift open front. 4. Menu label. 5. Button for drink selection. 6. Spill tray. Rev. A Service manual 2012-09-10...

  • Page 8: Description Of The Back Of The Machine

    QUATTRO 3.6 Description of the back of the machine Figure 4 1. Power switch. 2. Electrical supply. 3. Drain for manual tank. 4. Drain for heater tank. 5. Fan for ventilation. 6. Drain for overfill protection. 7. Inlet valve (for connection to mains water supply). Service manual Rev. A 2012-09-10...

  • Page 9: Description Of The Inside Of The Machine

    QUATTRO 3.7 Description of the inside of the machine Figure 5 Front (open position). Drink cartridge. Push buttons. Funnel. Button for rinsing. Filling, manual tank. Outlet nozzle. Spill tray. Slide, drink cartridge. Place for drink cartridges. Mixing bowl and steam trap. Rev. A Service manual 2012-09-10...

  • Page 10: Placement Of The Vending Machine

    QUATTRO 3.8 Placement of the vending machine Remove the packaging from the machine at the place it will be installed. Remove the transport protection. Check that the automatic machine and its parts have not been damaged during transport. If this is the case, then contact the forwarding agent and supplier immediately. WARNING Packaging materials such as styrofoam and plastic must be kept out of reach of children. • The machine is only intended for placement indoors in a dry place with a temperature above 12 degrees Celsius and a relative humidity below 75% Rh. 10 cm. • The machine may not be placed in an environ- ment where high pressure water is used for cleaning. • The machine contains electronic components. Avoid placement near microwave ovens, X-ray equipment or other equipment that generates high currents. Figure 6 • The highest ambient temperature during operation is max. 30 degrees Celsius. • The machine requires a installation area of 32 cm. in width, 45 cm. deep and 75 cm. in height. • Place the machine at least 10 cm from the wall so that the fan exhaust located on the back of the machine is not blocked (figure 6).

  • Page 11: Installation And Start-Up

    QUATTRO 4. Installation and start-up The machine is prepared for either direct connection to a mains water supply or manually filled via the built-in wa- ter tank. At first start-up or after the machine has been switched off for a long period of time, the machine will first attempt to take in water via the mains water inlet valve (7) for approx. 40 seconds. If this is unsuccessful, then the pump from the built-in water tank will start. 4.1 Installation and start-up, direct connection to a mains water supply Connect the machine from its inlet valve (7) to a mains water supply, using the enclosed hose (connection dimension 1/2” - 3/4”). Connect the enclosed cable with plug to a protective earthed electrical socket, 230VAC/50Hz. Connect the other connection to the switched socket on the back of the machine. Then ensure that the switch (3) on the back of the machine is in the “On” position “1”. Check that the red LED (1) is illuminated with a fixed red light. The machine heater tank is filled with water and heating begins. After approx. 5 minutes the red LED (1) should extinguish and the green LED (2) should shine with a fixed green light. The machine has then heated the water to a pre-set temperature. Keep in mind that the heater tank contains hot water, which can cause scalding. Rev. A Service manual 2012-09-10...

  • Page 12: Installation And Start-Up, Built In Manual Fill Water Tank

    QUATTRO 4.2 Installation and start-up, built in manual fill water tank Open then lift the front of the machine and push it backwards. Remove the blue fill cap marked “Water”. Fill with approx. 5 litres of cold water. Replace the blue fill cap and close the front of the machine. Connect the enclosed cable with plug to a protective earthed electrical socket, 230VAC/50Hz. Connect the other connection to the switched socket on the back of the machine. Then ensure that the switch (3) on the back of the machine is in the “On” position “1”. Check that the red LED (1) is illuminated with a fixed red light. The machine heater tank is filled with water and heating begins. The first fill from the manual fill tank takes approx. 1 minute. After approx. 5 minutes the red LED (1) should extinguish and the green LED (2) should shine with a fixed green light. The machine has then heated the water to a pre-set temperature. 4.3 Installation of drink cartridges Begin by removing the cartridge packaging. Then remove the cartridge bracket as per figures 7 to 9. This part of the cartridge is not used in this vending machine. Note: Never remove the rubber band. Figure 7...

  • Page 13: Loading Schedule

    QUATTRO Insert the cartridges as per fig- ures 10-12. Check that they locate properly into the grip hooks (figure 11 and 12). The cartridges must be placed in the correct order as per the loading schedule below. Figure 10 Figure 12 Figure 11 5 Loading schedule This vending machine is pre-programmed for 3 different loading schedules. As standard, loading schedule no. 1 is used. Place the drink cartridges as per the following: Nescafe Arabica Item no: 1053 Nescafe Espresso Grande Item no: 1069 Nesquick Lacté Item no: 1073 Skimmed milk Item no: 1018 Irrespective of loading schedule, cartridge number 4 can be replaced with: Cappuccino Topping Item no: 1088 Figure 13 Rev. A Service manual 2012-09-10...

  • Page 14: Loading Schedule, Variants

    QUATTRO 5. Loading schedule, variants Loading schedules are set as follows: Variant Volume (cl) Name Cartridge 1 Cartridge 2 Cartridge 3 Cartridge 4 Espresso Nesquick Skimmed Premium Arabica Grande Lacté milk Espresso Nesquick Skimmed Super Premium Arabica Grande Lacté milk Espresso Nesquick Skimmed Arabica Grande Lacté milk Variant Volume (cl) Drink Doses 1 Doses 2 Doses 3 Doses 4...

  • Page 15: Change Of Loading Schedule

    QUATTRO 5.2 Change of loading schedule As previously stated, the machine has 3 different loading schedules for 6 different drinks. This means that the drink strength and flavour can be varied according to personal preferences. To change from the preset loading schedule (1) to another, do as follows: Turn off the power to the machine (use the switch on the back). Wait approx. 5 sec. (until the green LED has extinguished). Hold in the desired drink button (1-3) for the desired loading schedule (figure 14). Turn on the power to the machine without letting go of the drink button. When the red LED light is lit, release the drink button. The red LED blinks 1 to 3 times to indicate the loading Figure 14 schedule that has been chosen. The change of the loading schedule is now complete. 5.3 Menu panel By holding in buttons 1-5, respectively button 6 (hot water) you can change the drink’s properties. The green LED blinks quickly during app. 5 seconds, then slowly. The following apply to these choices: If any drink button is held in until the green LED blinks • Buttons 1-5: slowly and is released during this period, then the coffe strength is reduced for drinks 1-4 and the chocolate’s strength for drink 5. Observe that the green LED first blinks slowly. If the drink button is released directly after pressing, then •...

  • Page 16: Daily Care And Cleaning

    QUATTRO 6 Daily care and cleaning In order for the vending machine to supply quality drinks and function optimally, it is important to perform a basic daily clean at regular intervals. This machine is built so that cleaning can be done by the user in a simple and effective manner. 6.1 Rinsing the mixer bowls This should be included in the daily cleaning and always at the end of the week or follow- ing longer periods when the machine is not in use. Open then lift the front of the machine and push it backward. Place a cup that holds at least 15 cl. on the spill tray (8, figure 15). Press the machine’s blue rinse button (5), the mixer bowls, hoses and nozzle will then be rinsed with hot water. 6.2 Cleaning the spill tray This should be included in the daily care routine. Remove the spill tray (8, figure 15). Figure 15 Empty the tray and rinse it. 6.3 External cleaning Wipe down the casing and spill tray with a mild cleaning agent or soapy water. Dry off using a soft cloth. Rinsing of the mixer bowls is done with hot water.

  • Page 17: Cleaning Of The Machine's Internal Parts

    QUATTRO 6.4 Cleaning of the machine’s internal parts We recommend you perform this process every week with normal use. Always switch off the power to the machine before you begin the cleaning process. 12 13 Figure 16 Parts that must be washed (figure 16): Quantity: Dispenser. Funnel. Fan duct (rear). Filter. Fan duct (front). Steam trap. Mixing bowl. Hose. Nozzle. Spill grate. Spill tray. Whipper. Lock ring (mixer bowl). Rev. A Service manual 2012-09-10...

  • Page 18: Disassembling The Machine's Internal Parts

    QUATTRO 6.5 Disassembling the machine’s internal parts Open then lift the front of the machine and push it backward. Remove the drink cartridges. Note their placement. Remove the two funnels (2, figure 16) by pulling them straight out. Remove the dispenser (figure 17) by pressing in the catch (1), then lift the dispenser upward and then straight out (2). Figure 17 Remove the hoses (8, figure 16) from mixer bowls (7, figure 16). Remove the mixer bowls by turning the lock ring counter clockwise (figure 18). Remove the whipper (12, figure 16) by pulling it outward. Remove the lock ring (figure 18) by turning it coun ter clockwise to stop and then pull it outward parallel to the whipper shaft. Figure 18 Pull out the fan duct (3, 5, figure 16) and open its two halves. Remove the filter (4). Remove the spill tray (11, figure 16) and its grate (10). Wash all of the parts in warm water. Be careful to dry all the parts before they are re-mounted as moisture has a negative effect on the machine’s function. Put the parts back together in reverse order as per the above. Ensure that the marking dot on the whipper is aligned with the flat edge on the whipper shaft. (figure 19), then press firmly until it clips fully in place.

  • Page 19: De-Scaling

    QUATTRO 6.6 De-scaling After the machine has been used for a while it must be de-scaled. This is particu- larly important if you use hard water (over 10 ºDH). De-scaling removes any lime scale deposits in the machine’s components and ensures that the machine contin- ues to function correctly. Always use Jede Cleaner for de-scaling. Use of any other agent that is not approved by Jede can cause the machine’s components to malfunction. De-scaling is done as follows: Switch off the power to the machine. If the machine is connected to a mains water supply then also shut off the water. Drain the machine’s water heater tank (1, figure 20) and the manual fill tank (2). Note that the water from the heater tank is very hot. Put back the clamps (3) on the hoses when the tanks are empty (figure 20). Mix 1.5 dl. Jede Cleaner with 3 litres cold water. Remove the blue fill cap marked “water” and pour the finished mixture into the manual fill tank. (figure 21). Figure 20 Start the machine and check that it func- tions normally, the red LED will extinguish after approx. 5 minutes, the green LED will then become illuminated with a fixed light. Note that any connection to the mains water supply must remain shut off. Place a vessel on the machine’s spill tray and then press the machine’s blue rinse button once (4, figure 23).

  • Page 20: Troubleshooting

    Figure 22 and then press the blue rinse button (4, figure 23). Switch off the power to the machine. Empty the machine’s heater tank (1) and manual fill tank (2). Put back the clamps (3) on the hoses when the tanks are empty (figure 22). Repeat points 8 to 0 a further three times. If the machine is connected to a mains water supply, then do not forget to turn the water back on once de-scaling is completed. Figure 23 If any of the drinks from the vending machine have a sour after taste follow- ing de-scaling, then repeat rinsing as per points 8 to 0. Jede Cleaner is not classed as hazardous to the health. 7 Troubleshooting The machine’s red LED can indicate errors with the aid of different blinking patterns. By following the instructions in chapter 7.2 (Error indicators), you can rectify minor problems in the machine’s function without having to call for service. Service manual Rev. A 2012-09-10...

  • Page 21: Resetting Errors

    QUATTRO 7. Resetting errors By pressing any of the six buttons for drink selection the present error will be reset as a result of the machine restarting. For example, this might rectify errors caused by temporary disturbance in the machine´s water supply. 7.2 Error indicators Number of blinks Cause Action Water filling error. Check the water connection. Check the overfill protection. Check the pump (manual fill tank). Check the inlet valve. Wrong water level after Check the water connection and serving. manual fill tank. Check the overfill protection. Check the level sensor. Over-current. Check the whipper motors. Check the dispenser motors. Temperature sensor Check the overheating protection. error. Check the temperature sensor. Check the PCB (TM-4). Level sensor error.

  • Page 22: Resetting Overheating Protection

    QUATTRO To reset the overfill protection do the following: Switch off the power to the machine. (Use the switch on the back). Turn off the mains water supply. Open the machine’s drainage plug for the overfill protection (2, figure 19). Let the water run out. Replace the drainage plug. Remove the hose from the inlet valve until the pressure in the hose is gone, 1 to 2 turns counter clockwise is normally sufficient (figure 25). Attach the hose to the inlet valve. Figure 25 Turn on the water to the machine. Switch on the power. If the above measures do not help, then see chapter 7.10 and 7.12. 7.4 Resetting overheating protection This applies to all machines regard- less of the type of water supply. The machine is equipped with overheating protection, which breaks the current to the heater tank’s element if the temperature in the tank becomes too high. The normal working temperature is 81 degrees Celsius. To reset the overheating protections do the following: Switch off the power to the machine (figure 26). Allow the water in the heater tank to cool down for at least 30 minutes.

  • Page 23: Removal Of Casing

    QUATTRO 7.5 Removal of casing Prior to beginning subsequent service, the machine’s plug must always be removed from the wall socket. To remove the machine’s upper casings do the following: Open the front of the machine and turn until the slip joint can be lifted out of Figure 27 its track. Remove the screws (1) from the front side of the machine (figure 27). Remove the screws (3) from the back side of the machine (figure 28). Lift the casing upward. When reassembling, ensure that the screws come into the correct thread by twisting them somewhat counter-clockwise. This is done so as not to cut up the existing threads. Figure 28 To loosen the machine’s lower casing, do the following: Remove the machine’s upper casings. Remove the screw (2) from the front side of the machine (figure 27). Remove the screws (4) from the back side of the machine (figure 28). Push the lower casing forward (figure 29) so that it is released from its keyhole (5). Figure 29...

  • Page 24: Replacing The Pump (Built-In Cold Water Tank)

    QUATTRO 7.6 Replacing the pump (built-in cold water tank) Remove the upper and lower casings. Loosen the pump’s electrical connections (1, figure 30). Remove hose (2) between pump and heater tank. Remove the pump from its inlet (3). Mount the new pump in reverse Figure 30 order. Note the colour markings on the cable clips (1). 7.7 Replacing the whipper motor Open the front of the machine Remove the funnel (2), mixer bowl (4), whipper (3) and the fixing plate for the mixer bowl (1, figure 31). Loosen the fixing screw (5, figure 32) for the whipper motor. Press lip (6) downward and lift out the whipper motor. Disconnect the motor’s electrical connections. Note the cable connections. Figure 31 When replacing the whisk motor, also replace the seal for the whipper axle or alternatively the complete fixing plate. Mount the new motor in reverse order. Note the cable connections concerning positive/negative pole. Figure 32 Service manual Rev. A...

  • Page 25: Replacing The Dispenser Motor

    QUATTRO 7.8 Replacing the dispenser motor Remove the upper casings and front. Remove the funnels and dispensers (see chapter 6.5). Loosen the left whisk motor’s electrical connections (1, figure 32). Remove the motor bridge by loosening its screws (2, figure 33) from the front side of the machine Figure 32 Lift out the motor bridge (5, figure 34) from the right side of the machine. Remove the cabling to the dispenser motor. Remove the dispenser motor (4, figure 34) by loosening its screws (3) from the underside of the motor bridge. Note that the crank (7) and its cam lobe (6) are keyed, that is to say they can only be joined together in a specific position. Figure 33 Change Prior to beginning service, the machine’s plug must always be removed from the wall socket. Note the cable connections with respect to colour marking. Be careful when dismantling so that the micro switch is not damaged. Figure 34 Rev. A...

  • Page 26: Replacing The Valve Unit

    QUATTRO 7.9 Replacing the valve unit Shut off the water supply to the machine and empty the water heater tank. Remove the upper casings and front. Remove the motor bridge (see chapter 7.8). Loosen all of the valve cabling and mark the cables so that they can be reassembled in the correct place. Loosen the hoses (2, figure 35) from the valve outlets. Remove the support for the valve packed by loosening the nut (1). Loosen the valve package from the Figure 35 tank. Replace the entire unit. Mount the new valve unit in reverse order. 7.0 Replacing the level sensor Shut off the water supply to the machine and empty the water heater tank. Remove the upper casings and front. Remove the lid of the water heater tank. Loosen cables (1, figure 36) to the level sensor (2) and mark them so that they can be remounted in the correct place. Figure 36 Press the level sensor 2) inward towards the water heater tank.

  • Page 27: Replacing The Temperature Sensor

    QUATTRO 7. Replacing the temperature sensor Shut off the water supply to the machine and empty the water heater tank. Remove the upper casings and front. Pull out the temperature sensor (1, figure 38) from its tube on the bottom side of the hot water tank. Remove any clips and loosen the temperature sensor’s connection (J18, figure 39) from the TSM card. Mount the new temperature sensor in reverse order. Figure 38 Prior to beginning service, the machine’s plug must always be removed from the wall socket. Note that the temperature sen- sor must be mounted to the full length of the temperature sensor’s tube. Figure 39 Rev. A Service manual 2012-09-10...

  • Page 28: Replacing The Inlet Valve

    QUATTRO 7.2 Replacing the inlet valve Shut off the water supply to the machine and empty the water heater tank and the cold water tank. Remove the upper/lower casings and front. Loosen the inlet valve’s cables (1, figure 40). Loosen the hose for filling the water heater tank (2). Loosen the hose for overfill protection/drainage (3). Figure 40 Remove the valve by loosening its two screws (4, figure 41) from the back side of the machine. Mount the inlet valve in reverse order. Figure 41 Prior to beginning service, the machine’s plug must always be removed from the wall socket. Service manual Rev. A 2012-09-10...

  • Page 29: Replacing The Push Button Panel

    QUATTRO 7.3 Replacing the push button panel Break the current to the machine and remove the front and the upper casings. Disconnect the connection for LED (1, figure 42) and the keypad (2). Remove the old push-button panel by loosening it in one corner. If the panel is difficult to remove, then a smaller screwdriver or similar tool orange can be used. Remove the protective film from the new push-button panel and put its flat strip cables in the intended slots (3, figure 43). Put the new push-button panel in place. Be careful to mount it in the correct position as the wiring can be damaged if you adjust it afterwards. Figure 42 Ensure that the flat strip cables are not twisted and connect them to the contacts, as per figure 42. Check the new panel’s function. Figure 43 Rev. A...

  • Page 30: Service Manual Rev. A

    QUATTRO 8 Removing the vending machine from service If the machine will not be used for a longer period of time, it is recom- mended that the following measures are taken for hygienic reasons Press the machine’s blue button for rinsing (see 6.1). Repeat this step 3 or 4 times. Remove the plug from the wall socket. Shut off any water connection and loosen the hose from the machine’s inlet valve. Clean the machine’s internal parts according to chapter 6.4 and 6.5. Remove all of the drink cartridges from the machine (see 4.3). Empty both water tanks if manually filled (see 6.6). Keep in mind that the heater tank contains hot water, which can cause scalding. 8. Transport If the machine is to be transported for longer distances, the following are recommended: Empty the machine’s water tanks (see 6.6). Remove all of the drink cartridges from the machine (see 4.3). Always transport the machine in its original packaging. If the machine is to be transported for shorter distances, the following are recommended: Empty the machine’s water tanks (see 6.6). If the machine is transported or moved with water in the heater tank, it will activate the inlet valve’s overfill protection and block it. Service manual Rev. A 2012-09-10...

  • Page 31: Technical Data

    Power output: 2000 W. Energy consumption (standby): 21,8 W/h. Auxiliary supply: 24 V DC. Warm water tank: 1,5 liter. Warm water tank, temp: 81˚C (Default operating temperature). Cold water tank: 6 litres total volume. Capacity: 4 Jedematic drink cartridges. Connective pressure water: 2-6 bar. 0 Service For repairs and service contact: Your Jede’s service supplier ◊ Always state the type of machine you have when ordering service. These details are found on the type plate (see 1.4). To ensure a continued problem free function of your machine, there is the opportunity to take out a service and care agreement. You can find out more information about this from your local retailer or via: www.jede.se  Warranty Jede AB is responsible for product faults that are due to defects in construction, materials or manufacturing during a period of 2 years (warranty period). Faults must be reported to Jede AB or its nearest retailer. Parts, which during the warran- ty period are established as faulty by Jede AB will be replaced through delivery of a new fault-free or repaired part. Jede has no responsibility beyond such replace- ment delivery. This warranty is not valid for negligent handling of the machine and only under the condition that the care instructions have been followed and that the machine has been used with Jede’s drinks for which it is intended. If original parts are not used, then the warranty will cease to apply and Jede AB will not be held responsible for any damage that occurs in and with the use of non-original parts.

  • Page 32: Energy Saving Function

    QUATTRO 2 Energy saving function This machine is equipped with a built-in energy saving function called S.L.E.P. This is a smart function where the machine itself learns what times of the day it is used and then adapts the energy saving function to suit. If the times the machine is used are changed, then the energy saving function will correct itself according to the current parameters. When the machine is in energy saving mode, this is indicated by the green LED slowly pulsating. If any drink is selected in this mode, then the red LED will be illuminated with a fixed light, which indicates that the machine’s heater tank is is heating up. This process can take up to 4 minutes. When the machine is then in its normal operating mode the red LED will be extinguished and the green LED will be illuminated with a fixed light. 3 Notes ................................................................................................................................................................................................................................................................................................................................................................................. Service manual Rev. A...
  • Page 33 QUATTRO .............................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................. Rev. A Service manual 2012-09-10...

  • Page 34: Front

    QUATTRO 4 Front Service manual Rev. A 2012-09-10...
  • Page 35 QUATTRO 4 Front * Cables and hoses are not illustrated on drawing. Recommended spare parts. Position Part number Term Quantity 36784 Lens 36778 Front panel, black 36807 Membrane button keypad Rev. A Service manual 2012-09-10...

  • Page 36: Casing

    QUATTRO 5 Casing Service manual Rev. A 2012-09-10...
  • Page 37 QUATTRO 5 Casing * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity 36774 Casing left 36799 Speed nut Screw RTK ST 3,5 x 13 36775 Casing right Rev. A Service manual 2012-09-10...

  • Page 38: Base Cover

    QUATTRO 6 Base cover DRAWN BoKo 2012-08-31 CHECKED TITLE APPROVED SIZE DWG NO bottenjäve SCALE Service manual Rev. A 2012-09-10...
  • Page 39 QUATTRO 6 Base cover * Cables and hoses are not illustrated on drawing. Recommended spare parts. Position Part number Term Quantity 36776 Bottom cover 36799 Speed nut 45499 Rubber foot 36779 Spill tray 36818 Spill grate Rev. A Service manual 2012-09-10...

  • Page 40: Mixer System

    QUATTRO 7 Mixer system Service manual Rev. A 2012-09-10...
  • Page 41 QUATTRO 7 Mixer system * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity 43977 Steam trap 35354 Mixer bowl 43973 Impellor 35353 Lock ring base 35352 Whipper motor Rev. A Service manual 2012-09-10...

  • Page 42: Tank Module

    QUATTRO 8 Tank module Service manual Rev. A 2012-09-10...
  • Page 43 QUATTRO 8 Tank module * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity Heater tank complete unit 36773 Divider chassis 36799 Speed nut 36710-5 PCB TM 4 Screw ST 3,5 x 13 Nut M6 36707 Transformer Screw M3 x 12 47291 Power entry with filter 45030 Y-Pipe 36277 Fan duct 36705 Drain pipe 46253 Ventil, inlopp 43095 Fan 24 V DC 36706 Nipple overflow 36345...

  • Page 44: Tank Complete Unit

    QUATTRO 9 Tank, complete unit Service manual Rev. A 2012-09-10...
  • Page 45 QUATTRO 9 Tank, complete unit * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity 36747 Insulation casing 36745 Seal probe 36748 Insulation lid 36291 36746 Probe 36788 Tank bracket 36744 Adaptor pipe 36278 Valve 2 + 1 43981 Seal, valve outlet 36809 Tank with element 2000 W 36743 Seal, tank outlet 35173 Cable green/yellow 36794 Cable water level 36829...

  • Page 46: Serving Module

    QUATTRO 20 Serving module Service manual Rev. A 2012-09-10...
  • Page 47 QUATTRO 20 Serving module * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity Motor unit 36771 Serving module 36782 Button keypad JM Dispenser Washer NB FZB 4 x 16 x 1 Screw MRT-TT M4 x 10 36786 Funnel 36816 Air filter 36785 Fan duct Mixer system Screw ST 3,5 x 13 43978 Adaptor 36573 Outlet pipe, brown 36287 Holder outlet pipe 36574 Outlet pipe, black 36744 Adaptor pipe 36791...

  • Page 48: Jm Dispenser

    QUATTRO 2 JM Dispenser Service manual Rev. A 2012-09-10...
  • Page 49 QUATTRO 2 JM Dispenser * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity Screw ST 3,5 x 13 36275-1 Holder, slide 43500 Holder, funnel/cartridge 36751 Slide Rev. A Service manual 2012-09-10...

  • Page 50: Motor Unit

    QUATTRO 22 Motor unit Service manual Rev. A 2012-09-10...
  • Page 51 QUATTRO 22 Motor unit * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Part number Term Quantity 36800 Dispenser motor 220 rpm. 36749 Crank 36750 Screw MRT-TT M4 x 10 42542 Micro switch Screw MRT-TT M3 x 12 36790 Motor bracket 36791 Cable S-module Rev. A Service manual 2012-09-10...

  • Page 52: Manual Fill Cold Water Tank

    QUATTRO 23 Manual fill cold water tank Service manual Rev. A 2012-09-10...
  • Page 53 QUATTRO 23 Manual fill cold water tank * Cables and hoses are not illustrated on drawing. Recommended spare parts Position Artikelnummer Benämning Antal 36787 Cap, blue 36744 Vent pipe 36819 Seal 36783 Tank, manual fill 43981 Seal 36598 Pump 36817 Plug, drain pipe 36801 Drain pipe Z93957 Clamp Rev. A Service manual 2012-09-10...

  • Page 54: Wiring Diagram 230 V

    QUATTRO 24 Wiring diagram 230 V Service manual Rev. A 2012-09-10...

  • Page 55: Wiring Diagram, Sensors

    QUATTRO 25 Wiring diagram, sensors Rev. A Service manual 2012-09-10...

  • Page 56: Wiring Diagram, Motors

    QUATTRO 26 Wiring diagram, motors Service manual Rev. A 2012-09-10...

  • Page 57: Wiring Diagram, Valves And Button Keypad

    QUATTRO 27 Wiring diagram, valves and button keypad Rev. A Service manual 2012-09-10...
  • Page 58 QUATTRO Manufacturer JEDE AB Box 303 SE-542 23 MARIESTAD Phone: +46(0)501 670 00 Fax: +46(0)501 670 67 Service manual article number: 37057 www.jede.com Service manual Rev. A 2012-09-10...

Table of Contents