Page 1
Manufacturer reserves the right to change specifications without notice. Note: Specifications may differ from country to country. WARNING: For your personal safety, READ and UNDERSTAND before using SAVE THESE INSTRUCTIONS Equipped with electric brake 16 mm (5/8”) MODEL HRIGODH 16 mm (518”) MODEL HRl6ODWH load speed Blows minute...
Page 2
IMPORTANT SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
Page 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o that keys and adjusting 15. AVOID UNINTENTIONAL STARTING. Don't carry tool with finger o n switch. Be sure switch is 16. EXTENSION CORDS. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry current your product in line voltage resulting in...
Page 4
VOLTAGE WARNING: Before connecting the tool t o a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that specified for the tool can result in SERIOUS INJURY t o the user as well as damage t o the tool.
Page 5
SAVE THESE INSTRUCTIONS contains important safety and operating instructions for battery charger. Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 1200, 1201 & 1201A. injury and damage.
Page 6
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents.
Page 7
ADDITIONAL SAFETY RULES Wear a hard hat (safety helmet), safety glasses and/or face shield. It is also highly recommended that padded gloves. Be sure the bit is secured in place before operation. Under normal operation, the tool is designed t o produce vibration. The screws can come loose easily, causing a breakdown or accident.
Page 8
Installing or removing the battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the tool.
Page 9
Side grip (auxiliary handle) The side grip swings around to either side, allowing easy handling of the tool in any position. Loosen the side grip by turning counterclockwise, swing it to the desired position and then tighten it by turning clockwise.
Page 10
Turn the change ring in the direction of the arrow until the mark on the change ring is aligned with mark on the rubber cap to secure the bit. gauge Depth The depth gauge is convenient for drilling holes of uniform depth. Insert the depth gauge into the hole in the grip base.
Page 11
Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the lever to the ' position for clockwise rotation or t h e position for c o u n t e r c l o c k w i s e rotation CAUTION: Always check the direction of rotation before operation.
Page 12
Torque limiter The torque limiter will actuate when a certain torque level is reached. The motor will disengage from the output shaft. When this happens, the bit will stop turning. CAUTIO As soon as the torque limiter actuates, switch off the tool immediately. This will help prevent premature wear of the tool.
Page 13
Rotate the chisel that the chisel faces toward Then secure the chisel and chisel dapter to the tool using the clamp screw on the chisel adapter. Set the action mode changing knob to "hammering only". Now you can use the chisel. To remove the chisel, CAUTIO N Always use "hammering only"...
Page 14
CAUTIO N : Never use "rotation with hammering" when the drill chuck assembly is installed on the tool. The drill chuck assembly may be damaged. Also, the drill chuck will come off when reversing the tool. NOTE: If you need assembled the drill chuck and chuck adapter assembly, proceed as follows. Secure the drill chuck in a vise or similar securing devise.
Page 15
Always be sure that the tool is switched off and the battery cartridge removed before attempting t o perform inspection maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replace- ment parts.
Page 16
18“ 24” 8” 8” Drill chuck 12” Part 763047-2 18” 8” 12” 18” Chuck adapter Part 122331-8 Blow-out bulb Part 765009-6 your Makita tool specified in this injury to persons. A-Taper bits w i t h hammers S I 3...
Page 17
100 g; 3.5 oz Bit grease Part 181 573-3 Dust cup Part 4 2 1 3 4 2 - 3 Dust extractor attachment Part 1921 76-8 Plastic carrying case Part No. 824445-6 Stopper pole Part No. 321 144-6 Safety goggle Part No.
Page 18
-08-'94 CORDLESS ROTARY HAMMER Model HRIGODH Note: The switch and other part configurations may differ from country to country.
Page 19
MODEL HHlGODH IFOM DESCRIPTION MACHINF 1 5 8 37 7 : ' O R ~ n q l i 'A,'$" DESCRIPTION M h E comprezs,on S p m g 6 Push Cane Pan Head Screw M 4 Screw 6 x 4 0 Impact Boll Rubber Ring 1 7 Idler...
Page 20
Take the battery to your nearest Makita Authorized Service Center or Distributor that has been designated as a Makita battery recycling location. Call your nearest Makita Service Center or Distributor to determine the location that provides Makita battery recycling. See your local Yellow Pages under "Tools-Electric'...