Table of Contents
Advertisement
Drill
Steel
10
mm
(3/8") MODEL
6404
Variable speedlReversIng
(RPM)
Wood
INSTRUCTION MANUAL
DOUBLE
INSULATION
SPECIFICATIONS
10
mm
(3/8")
I
15
mm
(5/8")
1
0
-
2,100
1
242 mm 19-9/16',)
I
1.4 kg (3.1
Ibs)
*
Manufacturer reserves the right t o change specifications without notice.
Note: Specifications may differ from country t o country.
Advertisement
Table of Contents
Related Manuals for Makita 6404
Summary of Contents for Makita 6404
- Page 1 Drill (3/8”) MODEL 6404 Variable speedlReversIng INSTRUCTION MANUAL DOUBLE INSULATION SPECIFICATIONS (RPM) Steel Wood 242 mm 19-9/16’,) 1.4 kg (3.1 Ibs) (3/8”) (5/8”) 2,100 Manufacturer reserves the right t o change specifications without notice. Note: Specifications may differ from country t o country.
- Page 2 SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT.
- Page 3 14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning AVOID UNINTENTIONAL STARTING. Don’t carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
- Page 4 ADDITIONAL SAFETY RULES Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations. Hold the tool firmly. Keep hands away from rotating parts. When drilling into walls, floors or wherever "live" electrical wires may be encountered, NOT TOUCH ANY METAL PARTS Hold the tool by the insulated grasping surfaces to prevent electric shock if...
- Page 5 Installing or removing drill bit CAUTION Always be sure that the tool is switched off and unplugged before installing or removing the bit. To install the bit, place will go. Tighten the chuck by hand. Place the chuck key in each of the three holes and tighten clockwise.
- Page 6 CAUTION Before plugging in the tool, always check to and returns to the "OFF" position when released. *Always check the direction of rotation before drilling. Use the reversing switch lever only when the tool comes to a complete stop. Changing the direction rotation before the tool stops may ruin the tool.
- Page 7 When this occurs, both carbon brushes should be replaced. To maintain product SAFETY and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, a!ways using Makita replacement parts. switched off and unplugged before attempting to perform certain length.
- Page 8 OPTIONAL ACCESSORIES The accessories listed in this manual are available at an extra cost from your Makita distributor or Makita factory Service center Service centers are listed on the warranty card packed with your tool CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual...
- Page 9 DrillChuckS 10 Gear BallBaaring6272 Housing (With Ibm 17) TerminslBaseCwnplsle FIELDASSEMBLY Bell Beadng626Z ARMATUREASSEMBLY 8-1 I ) (with item Fan52 Ball Bearing627Z SwilCh C a b n B N l h DuslCover Tapping Screw 4r25 (Wiih Item 5) Housing NanwPlale...
- Page 10 May-l0-'88 (318") DRILL Model 6404 Note: The switch and other part configurations may differ from country to country.
- Page 11 MAKITA LIMITED ONE YEAR WARRANTY Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers.