Advertisement
Quick Links
Cordless Driver Drill
Capacities
Steel
Wood
Wood
screw
Machlne screw
10"
21"
6 . 4 m m x 5 5 m m
6mm,1,4,,)
(318'7
(13/16"1
1114" x 2-3/16")
Equipped with Electric Brake
MODEL
621 1
DH
MODEL 621 1 D W H
With
Fast Charger
Dimensions
Net
IL
x
W x
HI
No
load speed IRPMl
weight
High
tow
o ~ 1 , 1 5 0 o - 3 7 0
2 3 3 m m x 7 9 m m x 2 3 3 m m
L B k g
19-3/16" x 3-118"
x
9~114")
13.7 lbsi
INSTRUCTION MANUAL
Battery Cartridge 1201
Voltage
SPECIFICATIONS
e
Model 6211DH
Model DC1201 Fast Charger
Input
output
Charging
time
12
v
I
A.C.
only
50 Hz
~
60 Hz
1
D.C 7.2V -
1 2 V
I
1
Hr
Manufacturer reserves the right t o change specifications without notice.
Note: Specifications may differ from country
to
country.
WARNING: For your personal safety, READ and UNDERSTAND before using
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
Advertisement
Related Manuals for Makita 6211DH
Summary of Contents for Makita 6211DH
- Page 1 Cordless Driver Drill INSTRUCTION MANUAL SPECIFICATIONS Model 6211DH Capacities Steel Wood Wood screw 10" 21" 6 . 4 m m x 5 5 m m (318'7 (13/16"1 1114" x 2-3/16") Battery Cartridge 1201 Model DC1201 Fast Charger Voltage A.C. Manufacturer reserves the right t o change specifications without notice.
-
Page 2: Safety Instructions
SAFETY INSTRUCTIONS WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. CONSIDER WORK AREA ENVIRONMENT. - Page 3 REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry tool w i t h finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS.
-
Page 4: Important Safety Instructions
Before using battery charger, read all instructions and cautionary markings battery charger, CAUTION To reduce risk of injury, charge only MAKITA Battery Cartridge 7000, 7001, 7002, 9000, 9001, 9002, 9100, 91 01, 91 1200,1201,1202,1201A, 1202A, 1210,1211 and 1222. Other types of batteries may burst causing personal injury and damage. -
Page 5: Additional Safety Rules
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature (104OF). or ABOVE 4OoC 2. Do not attempt t o use a step-up transformer, an engine generator or DC power receptacle. Do not allow anything t o cover or clog the charger vents. Always cover the battery terminals cartridge is not used. - Page 6 After charging, unplug the charger from the power source. CAUTION: The fast charger Model DC1201 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge.
- Page 7 Installing or removing driver bit or drill bit CAUTION : that Always be sure the tool is switched off and installing or removing the bit. Hold the ring and turn the clockwise to open the chuck jaws. Place the bit in the chuck as far as it will go. Hold the ring firmly and turn the clockwise to tighten the chuck.
- Page 8 Speed change To change the speed, slide the speed change lever to the "H" side for high speed or "L" side for low speed. To slide the speed change lever easily, pull the trigger slightly while pushing the speed change lever. Be sure that the speed change lever is set to the correct position before operation.
- Page 9 When driving wood screws, predrill pilot holes to make driving easier and to pre- vent splitting of the workpiece. See the chart. Drilling operation First, turn the adjusting ring so that the pointer on the adjusting ring points marking. Then proceed follows.
- Page 10 Hook A hook is provided as a standard equip- ment. This hook is convenient for tem- porarily hanging the tool. To install the hook, first insert one end of the hook into one slot in the .tool body and then insert the other end into the other slot.
-
Page 11: Maintenance
Always be sure that the tool is switched off and the battery cartridge i s removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. - Page 12 ACCESSORIES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present The accessories or attachments should be used only in the proper and intended manner.
- Page 13 CORDLESS DRIVER DRILL Model 6211D Note: The switch and other part configurations may differ from country to country.
- Page 14 ' L tM DESCRIPTION MACHINE Name Rata Tapping Screw PT4xl8 Housing Set [With Item 591 Pan Head Screw M4x22 IWith Washer) Sponge 14-72 Switch Lever Switch Lever Koylws Drill Chuck 10 Pan Head Screw M5x20 Spindle Bearing Retainer 14 Ball Bearing 6000LL8 Stop Ring Change...
- Page 15 ONE YEAR from the date of original purchase. Should tool, freight prepaid, the trouble is caused by defective workmmship o r material, Makita will repair (or replace) without charge. This Wananty docs not apply where: repairs have becn made npairi are required because The tool hss becn abused, misvsrd or improperly maintained;...