Related Manuals for Meyer Sound DS-2P
Summary of Contents for Meyer Sound DS-2P
-
Page 1: Operating Instructions
Operating Instructions Self-Powered Mid-bass Speaker Patents Pending Copyright © 1997, Meyer Sound Laboratories, Inc. All rights reserved Part #: 05.035.005.01 Rev B... -
Page 2: Declaration Of Conformity
6 sides Berkeley, California USA Vibration: 10 – 55 Hz (0.010 m October 1, 1995 peak-to-peak excursion) Made by Meyer Sound, Berkeley, CA, USA U U L L U U L L LISTED European Office: Meyer Sound Germany 3K59 ®... -
Page 3: Table Of Contents
ENTRETIEN E INTERNES NE SONT AUTORISEE Remote Monitoring TECHNIQUE QUALIFIÉ UK WARNING Meyer Sound, Berkeley, CA. USA THIS APPARAT R e m o t e M o n i t o r i n g S y s t e m... -
Page 4: Introduction
Windows-based PC. If the DS-2P shuts down due to either low or high voltage, the power supply automatically turns on after three seconds if the voltage has returned to either normal AC Power operating range. -
Page 5: Current Requirements
Current Requirements Safety Issues The DS-2P presents a dynamic load to the AC mains Pay close attention to these important electrical and which causes the amount of current to fluctuate between safety issues. quiet and loud operating levels. Since different types of... -
Page 6: Audio Input
For example, since the input impedance of a single DS-2P is 10 kΩ, cascading 20 DS-2Ps produces a brown = hot blue = balanced input impedance of 500 Ω. If a 150 Ω source is neutral used, the 500 Ω... -
Page 7: Fans And Cooling System
• a prolonged period of high source levels in hot distortion normally caused by clamping and clipping. temperatures or direct sunlight; As the DS-2P’s input signal is increased past the clamp- ing point, the output signal remains at a fixed level, • driver failure. -
Page 8: Rigging
Rigging Measurement and System Integration Tools The DS-2P weighs 221 lb (100 kg). The maximum recom- mended load for a single cabinet with aircraft pan fittings It is essential that even the most carefully assembled is 600 lb (273kg). This working load is based on a 5:1 safety sound systems be analyzed with precise measurement factor. -
Page 9: Complete Systems
The CH 1 DS-2 and Sub outputs drive the DS-2P and 650-P systems with the DS-2 & Sub Crossover switch in. With the DS-2 & Sub Crossover switch in, the DS-2 and Set the MSL-4 and DS-2P to the same polarity. -
Page 10: Driver Troubleshooting
(VU) for each amplifier channel, enabling a more complete driver diagnostic than the TPL LEDs. Set the CQ to the opposite polarity to the MSL-4 and DS-2P. Contact Meyer Sound for more information about RMS. The polarity of the 650-P depends on the height and distance of the measurement position from the the flown and subwoofer systems. - Page 11 Phase poppers are, therefore, not useful for performing phase measurements on an individual loudspeaker or a full-range sound system containing one or more cross- overs. If necessary, apply a phase popper only to loud- speakers with identical drivers without a crossover, and check the system’s overall phase response with a frequency analyzer and/or listening test.
-
Page 12: Array Design
Array Design for Low Frequencies SPL (+6 dB) compared to the same number in free-space. Although the DS-2P is a called a mid-bass speaker, it still NOTE: The trapezoidal shape of the DS-2P does not functions in the frequency realm of a subwoofer, especially represent the horizontal coverage area of the speaker. -
Page 13: Safety Summary
Safety Summary English Français • To reduce the risk of electric shock, disconnect the loud- • Pour réduire le risque d’électrocution, débranchez la prise speaker from the AC mains before installing audio cable. principale de l’haut-parleur, avant d’installer le câble Reconnect the power cord only after making all signal d’interface allant à... -
Page 14: Specifications
Notes 1. Acoustical specifications are for the minimum 3. Measured as the ratio between the peak SPL configuration of two DS-2P cabinets and are and the A-weighted noise floor. measured at 2 m on-axis from the 1/R image 4. Nominal 8 Ω resistive load, pink noise, 100 V (located at the rear of the cabinet).