Advertisement
Using Your Tower Fan
Switching the fan on
1.Place the fan on a flat level surface.
2.Insert the plug into a 230/240V power
outlet and turn the power on.
3.To switch on the fan, press
speed button (1, 2 or 3).
Switching the fan off
1.To switch the fan off, keep pressing the fan
speed button until it cycles through the fan
speeds and returns to Off.
2.If you will not be using the fan for a length
of time, it is advisable to turn the power off
at the wall socket and unplug the power
cord.
Remote control
Selecting a fan speed setting
Adjust the fan setting, timer and oscillation, or activate the night mode from anywhere in the
Your Sunbeam tower fan has 3 speed settings
room using the remote control.
as follows:
CORPORATION LTD.
•
low speed
•
medium speed
Power button
NOT TO SCALE
•
high speed
To select a fan speed, simply press the fan
Fan speed button
speed button
Choose from 3 speed settings,
Each press of the button will increase the
low medium or high.
fan speed and then return back to the lowest
speed again.
Oscillation
Your tower fan oscillates 70°,
distributing cool air throughout
the room.
Auto Off button
The auto off timer allows you
to set your tower fan to turn off
after 1, 2, 4 or 8 hours.
6 8
Top panel
the fan
RESTRICTED CONFIDENTIAL DOCUMENT
CH.
This drawing and all information shown hereon are the
exclusive property of Sunbeam Corporation Limited, and are
APPR.
submitted only on a confidential basis. The recipient agrees
not to reproduce the drawing, to return it upon request, and
that no disclosure of the drawing or the information shown
"1" light illuminates
hereon will be made to a third party without prior written
consent from the Sunbeam Corporation Limited.
13.03.2015
"2" light illuminates
3018-B-DS
"3" light illuminates
on the tower or the remote.
Using the auto off timer
The auto off timer automatically switches the
fan off after a preset number of hours.
To activate this feature, simply press the auto
off button
on the tower or on the remote
control unit.
1.
Press the auto off button once to switch
the fan off after 1 hour. The light on the
tower corresponding to the
illuminate.
2.
Press the auto off button again to have the
fan switch after 2 hours. The light on the
tower corresponding to the
illuminate.
3.
Similarly, pressing the auto off button a 3rd
or 4th time will set the fan to switch after 4
or 8 hours respectively. The corresponding
light on the tower
accordingly.
NOTE:
To cancel the setting, keep pressing the auto
These graphics must pass the f ollowing adhesio n tests; With the
graphics in place on the product scratch firmly with a finger nail with an
inward action. There should be no sign of damage to the markings. After
off timer button until it cycles past 8 hours
test 1,a length of scotch brand tape is to be firmly stuck over the
graphics, and rubbed down to ensure maximum adhesion of the tape.
Pull away from the surface at 90o at a constant rate. There should not
and returns to its normal setting. The auto
be any evidence of the graphic stuck to the tape. After test 2, rub for 15
seconds by hand with a piece of cloth soaked in water, and again for 15
seconds with a piece of cloth soaked in petroleum spirit (hexane). After
off timer will be deactivated, the timing light
Night mode
this test check that markings are easily legible, and that the graphics
can not be easily removed and show no signs of becoming detached
from the surface to which they are applied.
will be off, and the fan will remain on until it
Turns off all bright lights on
is switched off manually.
the control panel, leaving only
a dim Night Mode light.
This keeps the room dark when
Using the oscillation function
being used at night, ideal for
The 70 degree oscillation function can be
when sleeping.
used on any setting.
1.
Turn the unit on and select any fan speed.
2.
Press the
button on the tower or the
Sleep Breeze mode
remote. The fan will begin to oscillate from
In sleep breeze mode
side to side.
the airflow decreases over time
To stop the fan from oscillating, simply
and then turns off automatically.
press the
button once again.
This is ideal for when sleeping.
position will
position will
or
will illuminate
5 5
Hide quick links:
Advertisement
