NAD CI940 Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. CI940
  6. Owner's manual

NAD CI940 Owner's Manual

Multi-channel amplifier
Hide thumbs Also See for CI940:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Service Manual
CI940
®
Multi-Channel Amplifier
Multi-Channel Amplifier CI 940
© NAD CI940
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CI940 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for NAD CI940

Summary of Contents for NAD CI940

  • Page 1 CI940 ® Multi-Channel Amplifier Multi-Channel Amplifier CI 940 © NAD CI940 Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 14 Outdoor Antenna Grounding - If an outside antenna or cable system SAVE THESE INSTRUCTIONS FOR LATER USE. is connected to the product, be sure the antenna or cable system is FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE AUDIO grounded so as to provide some protection against voltage surges EQUIPMENT.
  • Page 3 (including amplifiers) that produce heat. CAUTION Changes or modifications to this equipment not expressly approved by NAD Electronics for compliance could void the user’ s authority to operate this WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS equipment.
  • Page 4 Serial no.: ........NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited...

  • Page 5: Getting Started

    After installing the speaker cables to the supplied speaker connectors, · Should water get into your NAD CI 940, shut off the power to the unit plug in the speaker connector to ZONE 1 (and/or ZONE 2) speaker and remove the plug from the AC socket. Have the unit inspected by a terminal of CI 940.

  • Page 6: Identification Of Controls

    IDENTIFICATION OF CONTROLS FRONT PANEL Multi-Channel Amplifier CI 940 © NAD CI940 1 STANDBY BUTTON · Press this button to switch ON the CI 940. The Standby LED indicator will turn from amber to blue. · Pressing the Standby button again turns the unit back to standby mode.

  • Page 7: Rear Panel

    IDENTIFICATION OF CONTROLS REAR PANEL INPUT OUTPUT INPUT OUTPUT ATTENTION! Please make sure that the CI 940 is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections. 1 ZONE 2 (INPUT/OUTPUT) ·...
  • Page 8 IDENTIFICATION OF CONTROLS REAR PANEL 7 +12V TRIGGER IN/INPUT SENSE - OFF/AUTO 9 FUSE HOLDER · This dual function switch alternates between sensing a +12V input · In the unlikely event a fuse may need to be replaced, unplug the AC as applied through the +12V TRIGGER IN jack or sensing any active cord from the wall.
  • Page 9 IDENTIFICATION OF CONTROLS REAR PANEL AUTOMATED TURN-ON LOGIC (ATO LOGIC) CI 940 to be switched back to standby mode in the same manner it was The CI 940 may be turned ON in three discrete ways for complete system activated. In other words, if the CI 940 is switched ON via a +12V-control flexibility - from the front panel standby button, the 12V-TRIGGER circuit or signal, it cannot be switched to standby mode via the front panel STANDBY by the input signal-sensing circuit.

  • Page 10: Troubleshooting

    REFERENCE TROUBLESHOOTING CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS No power. • The power cord is disconnected. • Plug the power cord into the wall outlet securely. • CI 940 at standby mode. • Press the front panel STANDBY button to switch ON the CI 940. (+12V TRIGGER IN/INPUT SENSE switch set to OFF position) •...

  • Page 11: Overall Specifications

    8.4 kg (18.5 lbs) NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL. THE CI 940 OWNER’S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. CHECK OUT WWW.NADELECTRONICS.COM FOR THE LATEST VERSION OF THE CI 940 OWNER’S MANUAL.
  • Page 12 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents