NAD CI980 Owner's Manual
  1. Manuals
  2. Brands
  3. NAD Manuals
  4. Amplifier
  5. CI980
  6. Owner's manual

NAD CI980 Owner's Manual

Multi-channel amplifier
Hide thumbs Also See for CI980:
Table of Contents

Advertisement

Quick Links

See also: Service Manual
CI980
®
Multi-Channel Amplifier
Multi-Channel Amplifier CI 980
© NAD CI980
Owner's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CI980 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for NAD CI980

Summary of Contents for NAD CI980

  • Page 1 CI980 ® Multi-Channel Amplifier Multi-Channel Amplifier CI 980 © NAD CI980 Owner’s Manual...

  • Page 2: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS 14 Outdoor Antenna Grounding - If an outside antenna or cable system SAVE THESE INSTRUCTIONS FOR LATER USE. is connected to the product, be sure the antenna or cable system is FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED ON THE grounded so as to provide some protection against voltage surges AUDIO EQUIPMENT.
  • Page 3 (including amplifiers) CAUTION that produce heat. Changes or modifications to this equipment not expressly approved by NAD WARNING Electronics for compliance could void the user’ s authority to operate this TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS equipment.

  • Page 4: Notes On Environmental Protection

    Serial no.: ........NAD is a trademark of NAD Electronics International, a division of Lenbrook Industries Limited...

  • Page 5: Getting Started

    After installing the speaker cables to the supplied speaker connectors, • Should water get into your NAD CI 980, shut off the power to the unit plug in the speaker connector to corresponding ZONE (ZONE 1- 4) and remove the plug from the AC socket. Have the unit inspected by a speaker terminal of CI 980.

  • Page 6: Identification Of Controls

    IDENTIFICATION OF CONTROLS FRONT PANEL Multi-Channel Amplifier CI 980 © NAD CI980 1 STANDBY BUTTON • Press this button to switch ON the CI 980. The Standby LED indicator will turn from amber to blue. • Pressing the Standby button again turns the unit back to standby mode.

  • Page 7: Rear Panel

    INPUT OUTPUT INPUT OUTPUT © NAD CI980 10 11 ATTENTION! Please make sure that the CI 980 is powered OFF or unplugged before making any connections. It is also advisable to power-down or unplug all associated components while making or breaking any signal or AC power connections.

  • Page 8: Ac Mains Input

    IDENTIFICATION OF CONTROLS REAR PANEL 5 INPUT/OUTPUT (ZONE 1 - 4) IMPORTANT NOTICE • These INPUT/OUTPUT terminals are dedicated to their respective Do not use any substitute fuses of different types or with different ratings ZONE SPEAKERS. or values. Failure to observe this precaution may cause damage to the •...

  • Page 9: Troubleshooting

    REFERENCE TROUBLESHOOTING CONDITION POSSIBLE CAUSES POSSIBLE SOLUTIONS No power. • The power cord is disconnected. • Plug the power cord into the wall outlet securely. • CI 980 at standby mode. • Press front panel STANDBY button to switch ON the CI 980 (TRIGGER OFF/ON/AUTO switch set to OFF position).

  • Page 10: Overall Specifications

    7.1 kg (15.7 lbs) NAD SHALL NOT BE HELD LIABLE FOR ANY TECHNICAL OR USER INTERFACE DISCREPANCIES IN THIS MANUAL. THE CI 980 OWNER’S MANUAL MAY BE SUBJECT TO CHANGE WITHOUT PRIOR NOTICE. CHECK OUT WWW.NADELECTRONICS.COM FOR THE LATEST VERSION OF THE CI 980 OWNER’S MANUAL.
  • Page 12 All rights reserved. NAD and the NAD logo are trademarks of NAD Electronics International, a division of Lenbrook Industries Limited. No part of this publication may be reproduced, stored or transmitted in any form without the written permission of NAD Electronics International.

Table of Contents