Related Manuals for Hark HK0522
Summary of Contents for Hark HK0522
- Page 1 2 DOOR GAS SMOKER Owner’s Manual ASSEMBLY, CARE & SAFETY INSTRUCTIONS Item No. HK0522 Certification AGA 7592 G...
- Page 2 You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. After Sales Support YEAR WARRANTY Telephone: 1300 799 787 (03) 9873 2711 Email: service@hark.com.au...
- Page 3 READ ALL SAFEGUARDS AND INSTRUCTIONS THOROUGHLY! YOUR SAFETY IS VERY IMPORTANT – FAILURE TO FOLLOW PROPER PROCEDURES AND SAFEGUARDS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. DANGER DANGER - This smoker is for OUTDOOR USE ONLY. - Do not allow anyone to conduct activities around - Never operate this smoker unattended.
-
Page 4: Save These Instructions
READ ALL SAFEGUARDS AND INSTRUCTIONS THOROUGHLY! YOUR SAFETY IS VERY IMPORTANT – FAILURE TO FOLLOW PROPER PROCEDURES AND SAFEGUARDS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. DANGER DANGER • Do not obstruct flow of combustion and • Always allow the hot water to cool completely ventilation. - Page 5 A. HARDWARE PACK NO. Description. Finish Note 1/4-20x1/2 Screw Black galvanized 19 Inside blister card 1/4-20 Flange Nut Black galvanized 8 10-24x1/2 Screw Black galvanized 11 10-24Nut Black galvanized 3 Inside blister card M5 spring washer Black galvanized 3 S hook for hose Chrome plated Inside blister card Zip tie...
-
Page 6: Table Of Contents
B. PARTS LIST Read all safeguards and assembly instructions before assembling and operating your smoker. Before assembling your new smoker, unpack all parts from the box. Carefully remove all packing material and lay out all the parts for easy access and identification. -
Page 7: Smoker Cabinet
C. ASSEMBLY INSTRUCTIONS WARNING DO NOT HANDLE SMOKER BY THE CROSS BAR ON SMOKER CABINET. DO NOT LIFT OR MOVE USING THIS CROSS BAR. Step 1 Locate: Cabinet (1), lower door (2) and upper door(3) Note: The doors are attached to the cabinet Procedure: —... -
Page 8: Burner Chamber Assembly
STEP 3 Locate: Control Panel Assembly [5], two 1/4-20x1/2” Screw [1a] (two remaining from previous step) Tools needed: Philips head screwdriver. Procedure: — Place the control panel assembly between the front legs as shown. There are slots on the control panel that fit around the legs and line up with the bolt holes. - Page 9 STEP 5 Locate: Dampers [7], three 10-24x1/2” Screws [3c], 10-24 Nuts [4c], M5 Spring Washers [5c] From hardware Pack - Blister card Tools needed: Philips head screwdriver and 3/8” wrench or shifter. Procedure: — From the outside of the cabinet, insert a 10-24x1/2”...
- Page 10 STEP 6 Locate: Two Side Handles [18], eight 1/4- 20x1/2” Screw [1a], and eight 1/4-20 Flange Nuts [2a] Tools needed: Philips head screwdriver and a 7/16” wrench or pliers Procedure: — Use four 1/4-20x1/2” Screw [1a] and four 1/4-20 Flange Nuts [2a] to attach the handle on the right side of the smoker cabinet [1].
- Page 11 STEP 10 Locate: Door Latch Plate (17) and 4 x 10-24x1/2” Screws. Tools Needed: Phillips head screwdriver Procedure: —Attach each door latch plate (17) to the upper and lower doors using 2 x 10-24x1/2” screws. Each latch plate is fastened to the side of the doors using two screws.
-
Page 12: Smoker Leg
Step 13 Locate: 2 x Grid Tracks (13), 1 x Water Bowel. Tools Needed: None Procedure: Install one grid track (13) in each of the next holes up from the bottom hole, located in the grid support for both the left and right hand sides of the cabinet. - Page 13 Assembly of your smoker is now completed. The following image shows how the assembled unit should look.
- Page 14 D. THE GAS SYSTEM DANGER ALL INSTRUCTIONS AND SAFEGUARDS MUST BE FOLLOWED TO PREVENT FIRE, PROPERT Y DAMAGE, OR PERSONAL INJURY. CONNECTING THE HOSE AND REGULATOR TO THE GAS AND REGULATOR INFORMATION GAS BOTTLE This smoker is designed for propane (LPG) gas •...
- Page 15 Please note that the hose is already fitted to the valve on the underside of the control panel of the smoker. You do not have to adjust this connection but should leak test this once the hose and regulator are connected to the gas cylinder. DO NOT DISCONNECT HOSE FROM VALVE.
- Page 16 GAS BOTTLE RESTRAINT Included is a strap with a hook at either end. This is to be used to secure the gas bottle to the smoker. Once you have fully assembled your smoker with the gas bottle connected, connect one end of the strap to the side handle of the smoker nearest to the gas bottle and the other end of the strap to the gas bottle handle.
- Page 17 E. OPERATION: BEFORE USE ADDING WOOD: PRE-USE PROCEDURES: Before you cook food in your smoker, it is To add wood before cooking, simply fill the important to “season” your smoker. Seasoning wood chip box with your choice of flavouring seals the paint and interior of your smoker hardwood chips.
-
Page 18: Damper
F. OPERATION: LIGHTING LP GAS LIGHTING PROCEDURE: 1. Check all connections for leaks using the leaktest as explained on page 15. 2. Open the smoker door. WARNING NEVER ATTEMPT TO LIGHT THE SMOKER WITH THE DOOR CLOSED OPEN DOOR TO LIGHT SMOKER 3. -
Page 19: Water Bowl
G. OPERATION: COOKING DAMPER ADJUSTMENTS • You are now ready to light the burner. Refer to the Temperature maintenance is best controlled Lighting Procedure on the previous pages of this by different damper adjustments. The key to effective manual. The heat from the burner will allow the wood smoking is to watch your heat indicator on the door chips to burn, causing the flavouring smoke to and adjust the damper accordingly. -
Page 20: Side Handle
I. AFTER USE SAFETY AND MAINTENANCE WARNING • Use caution when lifting and moving the smoker to avoid strains or back injury. 2 people are recommended to lift or move the smoker. • DO NOT store the smoker near gasoline or other combustible liquids or where combustible vapour may be present. - Page 21 Diagrammatical Representation of "OUTDOOR AREAS" THIS APPLIANCE SHALL ONLY BE USED IN AN ABOVE GROUND OPEN-AIR SITUATION WITH NATURAL VENTILATION, WITHOUT STAGNANT AREAS, WHERE GAS LEAKAGE AND PRODUCTS OF COMBUSTION ARE RAPIDLY DISPERSED BY WIND AND NATURAL CONVECTION. THIS SMOKER IS NOT DESIGNED FOR MARINE USE.
- Page 22 — Within a partial enclosure that includes an overhead cover and more than two walls, the following shall apply: a) at least 25% of the total wall area is completely open, and b) at least 30% of the remaining wall area is open and unrestricted (Refer to examples 3, 4 and 5).
-
Page 23: Replacement Parts
Made in China. Guangdong Kangbao Electrical Co., LTD Made in China This product is manufactured by: Imported by: Co., Ltd. Hark Enterprises Pty Ltd Guangdong Kangbao Electrical 268th Qixin Road, Xingtan Town. Unit 11, 41-49 Norcal Rd Shunde District, Foshan City, Nunawading, VIC, 3131 Guangdong Province. - Page 24 Hark Enterprises Pty Ltd Unit 11, 41-49 Norcal Rd, Nunawading, VIC 3131 T: 1300 799 787 E: service @ hark.com.au W: www.hark.com.au...