Advertisement
P L E A S E R E A D A N D S AV E T H E S E
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
When using electrical appliances, basic safety precautions
electric shock or fire, or damage the heater.
should always be followed to reduce the risk of fire,
11. To prevent a possible fire, do not block air intakes or
electric shock, and injury to persons, including the
exhaust in any manner. Do not use on soft surfaces,
following:
like a bed, where openings may become blocked.
12. A heater has hot and arcing or sparking parts inside.
1. Read all instructions before using this heater.
2. This heater is hot when in use. To avoid burns, do not
Do not use it in areas where gasoline, paint, or
flammable liquids are used or stored.
let bare skin touch hot surfaces. If provided, use
13. Use this heater only as described in this manual. Any
handles when moving this heater. Keep combustible
materials, such as furniture, pillows, bedding, papers,
other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons.
clothes, and curtains at least 3 feet (0.9 m) from the
14. Always plug heaters directly into a wall outlet/
front of the heater and keep them away from the
sides and rear.
receptacle. Never use with an extension cord or
relocatable power tap (outlet/power strip).
3. Extreme caution is necessary when any heater is
used by or near children or invalids and whenever
15. When unplugging, be sure to pull by the plug and
the heater is left operating and unattended.
not the cord.
4. Always unplug heater when not in use.
16. If the heater will not operate, see specific instructions
on Auto Safety Shut-off.
5. Do not operate any heater with a damaged cord or
plug or after the heater malfunctions, has been
17. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
dropped or damaged in any manner. Discard heater,
your warranty. The inside of the unit contains no user
or return to authorized service facility for
examination and/or repair.
serviceable parts. All servicing should be performed
by qualified personnel only.
6. Do not use outdoors.
18. Discontinue use if plug or outlet is hot. It is
7. This heater is not intended for use in bathrooms,
recommended that the outlet be replaced if plug or
laundry areas and similar indoor locations. Never
locate heater where it may fall into a bathtub or
outlet is hot to touch.
19. The heater must not be located immediately below a
other water container.
socket-outlet. Do not use this heater in the
8. Do not run cord under carpeting. Do not cover cord
with throw rugs, runners, or similar coverings. Do not
immediate surroundings of a bath, a shower or a
swimming pool.
route cord under furniture or appliances. Arrange
cord away from traffic area and where it will not be
SAVE THESE
tripped over.
9. To disconnect heater, turn controls to off, then
INSTRUCTIONS
remove plug from outlet.
10. Do not insert or allow foreign objects to enter any
ventilation or exhaust opening as this may cause an
THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.
DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS
SAFETY FEATURE IN ANY WAY.
BCH9214RE-BM_14EM1.indd 2
F E AT U R E S - O P E R AT I O N S
TECHNICAL SPECIFICATIONS
NOTES:
• THIS PRODUCT CONTAINS A BUTTON BATTERY. IF
• Amps: 12.5
• Wattage: 1500W (+5% –10%)
SWALLOWED, IT COULD CAUSE SEVERE INJURY IN JUST 2
HOURS. SEEK MEDICAL ATTENTION IMMEDIATELY.
• Working voltage: 120V AC/60Hz
• Remove the battery from the equipment when it is not
Remote Control
being used for an extended period of time.
• Remove the used battery promptly.
Unpack the remote control from box. This includes one
• Do not discard used batteries into household trash
lithium battery, CR2025/3V. Please note this remote
containers. Contact your local government for disposal or
control will not work through walls. Remove battery
recycling practices in your area.
before discarding the remote.
NOTE: REMOVE THE PROTECTIVE COVER FROM THE
FCC STATEMENT
BATTERY PRIOR TO BEGINNING OPERATION.
Battery Replacement
Potential for Radio/Television interference
1. Locate the battery compartment on the back of the
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
remote control handset. Insert a small object (such as
not cause harmful interference, and (2) this device must
a pin or paper clip) into the hole of the battery cover
accept any interference received, including interference that
lock (see Figure 1) and slide out the battery cover.
may cause undesired operation.
2. Remove old battery.
This product has been tested and found to comply with the
3. Place new battery into battery compartment.
4. Slide battery compartment into the remote control
limits for a Class B digital device, pursuant to part 15 of the
FCC rules.
handset until the Battery Cover Lock is securely latched.
5. For your convenience, a remote control holder is
These limits are designed to provide reasonable protection
integrated into the back of the heater housing.
against harmful interference in a residential installation. The
product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
Figure 1
instructions, may cause harmful interference to radio
A
communications. However, there is no guarantee that the
Insert pin here
interference will not occur in a particular installation. If the
product does cause harmful interference to radio or television
reception, which can be determined by turning the product on
or off, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the product and the
receiver.
• Connect the product into an outlet on a circuit different
B
from that to which the receiver is connected.
A. Battery Cover Lock
• Consult the dealer or an experienced radio/TV technician
B. Battery cover
for help.
• Changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate the equipment.
F E AT U R E S - O P E R AT I O N S
OPERATING INSTRUCTIONS
Mode Selection
1. Place heater on a firm, level surface.
Select your desired heat settings by pressing the
2. Plug heater into a standard outlet. Once plugged in, the
corresponding buttons as located on your heater or press the
Power Light will illuminate.
Mode button on remote control to cycle through the heat
NOTE: Avoid overloading your circuit by not using other
settings. An indicator light will illuminate next to each button
high wattage appliances in the same outlet. At 1500
to indicate that the selected setting/mode is activated.
watts, this unit draws 12.5 Amps.
3. Operate heater by pressing the Power Button ( ) and
Fan Only Setting
selecting modes and settings according to preference.
Press the Fan Only Button to run the heater without heat
NOTE: Remove the plastic film from the control panel
output. The Stay On icon will appear on the LCD Display.
before using (if included).
– HIGH Heat Setting
Power On/Off
Press the Max Heat Button to run the heater continuously
Press the Power On/Off Button to turn the heater on. Once
at 1500W. The Stay On icon will appear on the LCD Display.
on, the heater will run in the Max Heat mode and the
Stay On icon will appear on the LCD Display. Press the
Eco-Smart™ Setting
Power On/Off button to manually turn off the heater at any
Press the Eco-Smart™ Button to activate the energy
setting.
efficient Eco-Smart™ Mode. The heater will now cycle
NOTE: The Power Light will remain illuminated while unit is
between high (at 1500W) and low (at 750W) heat settings to
plugged in.
provide heat. The Stay On icon will appear on the LCD Display.
Thermostat Control
Figure 2
Your heater is equipped with a digital thermostat that allows
you to set your heater to a precise comfort level by turning
the Dial Wheel on the control panel or pressing the arrow
buttons on the remote control:
Turn the Dial Wheel to activate. The Thermostat icon ( )
will appear on the LCD Display.
To preset a precise comfort level, turn the Dial Wheel to
adjust the temperature from 85°F to 65°F (Default:
"85"). The LCD Display will show the selected temperature
reading. When the preset temperature is reached, the heater
will shut off and cool down for 15 seconds. When the room
temperature drops below the preset temperature, the heater
E
D
C
A
B
will automatically turn on again to maintain the preset
temperature level.
FrostProtect™ Setting
A Control Buttons
B LCD Display
Your heater is equipped with FrostProtect™ setting. The
C Dial Wheel
heater will turn on automatically when the room temperature
D Power Light
drops below 40°F. To activate FrostProtect™ setting, turn the
E Remote Control
Dial Wheel to show "40" and the FrostProtect™ icon
( ) will appear on the LCD Display.
F E AT U R E S - O P E R AT I O N S /
C L E A N I N G / M A I N T E N A N C E
NOTE: It is normal for the heater to cycle on and off to
1. Press the Timer Button ( ) once. The indicator light will
maintain the preset temperature. Raise the thermostat setting
begin to blink for 5 seconds. The LCD Display will show
or operate in Stay On mode to prevent the heater from
"0" and the "Hr" icon.
cycling. When the preset temperature is reached or when the
2. Turn the Dial Wheel on the control panel to adjust from
heater is shut off, the fan will run for 15 seconds without
0 to 24 to select your desired time interval for the
heat. This cool down process ensures an accurate and
heater to shut-off automatically. The selected hour will
consistent temperature reading.
appear on the LCD Display, and then the Timer indicator
light will stop blinking in 3 seconds to indicate that the
NOTE: To shut the heater off at any setting, press the Power
selected timer is activated. The LCD Display will return to
Button ( ) until the LCD Display goes off. The heater will
show the preset temperature and mode setting.
cool down for 15 seconds, and the Fan Only indicator light
will blink in Amber until cool down is completed. The digital
3. To cancel the Timer feature, press the Timer Button ( )
thermostat has memory; it will remember the last
twice within 5 seconds, the Timer indicator light will go
off.
temperature setting before the heater is turned off. However,
if the heater is unplugged, the digital thermostat will no
NOTE: The timer does not work with the FrostProtect
Setting.
TM
longer remember the previous temperature setting. You will
need to reset the digital thermostat if the heater is
CLEANING/MAINTENANCE
unplugged.
Always unplug the heater before cleaning and allow the
heater to cool down.
Oscillation
1. Clean the unit with a soft cloth moistened with a mild
Press the Oscillation Button (
) on control panel or
soap and water solution.
remote control to activate or stop the oscillation feature.
2. NEVER use abrasive or flammable solvents to clean the
NOTE: Please do not manually turn the heater on the base.
unit.
It is designed to turn only by motorized oscillation.
3. After cleaning, be sure to completely dry the unit with a
cloth or towel.
Timer
TIP: Over time, dust may accumulate on the front grills.
Your heater is equipped with 24-Hour Auto Shut-off Timer
This can be removed by wiping the unit with a damp
cloth.
feature. This allows you to program your heater to shut off
automatically after running a defined time interval (from 0
to 24 hours).
A U T O S A F E T Y S H U T- O F F /
H E AT E R S T O R A G E
AUTO SAFETY SHUT-OFF
This heater is equipped with a technologically-advanced safety system that requires the user to reset the heater if there is a
potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater
off. It can only resume operation when the user resets the unit.
If the heater shuts down and the Power Light is flashing:
1. Stand the heater upright.
2. Unplug the heater and allow 30 minutes for the heater to cool down.
3. After 30 minutes plug the heater in and operate normally.
4. If the heater does not work normally, repeat steps 1, 2 and 3 again.
NOTE: If the heater is plugged in again and Power On/Off Button is pressed within the 30-minute cool down period, heater
will run at Max Heat setting, but shut down in 2 seconds with the Power Light flashing. Please repeat the above 4 steps to
reset the heater again and ensure to allow sufficient time for the thermostat to cool down.
Tip Over Shut-Off:
When the unit is accidentally knocked over, it will instantly shut off and the Power Light will flash. The unit may also shut off
if it is moved or bumped. To reset, simply place the heater in an upright position, the Power Light will stop flashing and it will
operate normally.
NOTE: If unit does not turn on when placed in the upright position, press Power On/Off Button once and heater will resume
operation.
HEATER STORAGE
1. Store heater unit with cord in a cool, dry location.
2. We recommend storing the unit and cord in the original package.
9/05/14 9:00 AM
Advertisement
