Page 1
INSTRUCTION MANUAL VCB-3442P BEDIENUNGSANLEITUNG MANUEL D’INSTRUCTIONS B/W CCD Camera CCD-Schwarzweißkamera Caméra CCD Noir et Blanc About this manual A propos de ce manuel Before installing and using the camera, please read this Avant d’installer et d’utiliser la caméra, veuillez lire ce manual carefully.
Depending on the conditions of use, installation and environment, FEATURES please be sure to make the appropriate settings and adjustments. If you need help with installation and/or settings, please consult your dealer. • Built-in interline transfer method 1/3" CCD, approx. 320,000 CONTENTS picture elements •...
Disconnect the power greasy smoke or steam, where the dampness may get too high, or cord immediately, and consult your dealer (or a Sanyo Authorized where there is a lot of dust.
PARTS NAMES Camera setup section • Electronic iris (EI)/Auto iris (AI) setting • Backlight compensation (BLC) setting • Automatic gain control (AGC) setting SHUTTER VIDEO OUT Power indicator (POWER) Comes on when the power to the camera is on. POWER 12 V DC input terminal (12 V DC, GND) DC12V High speed electronic shutter switch (SHUTTER)
Page 5
PARTS NAMES Flange-back lock screw Lens mount cap The cap is installed to protect the lens mount section. Remove the lens mount cap before installing a lens (sold separately). Camera installation bracket The bracket can be fixed at the top or bottom of the camera. Camera mounting screw hole: 1/4"-20 UNC CAUTION: When installing the camera support, select a location that can support the total weight of the...
Page 6
ALC and LEVEL volume level controls are available on the lens for iris adjustments. (Set the Auto-iris lens switch to the VIDEO position.) Compatible auto-iris lenses 1/3 inch Sanyo DC type lens VIDEO type lens VCL-CS8LY: Standard angle, f= 8 mm...
MOUNTING THE LENS Please use a DC type auto-iris lens (sold separately). Checking the lens mount Do not use a lens if length “L” is more than 9 mm. If not, that may damage the camera and prevent proper installation. Remove the lens mount cap from the camera.
Page 8
MOUNTING THE LENS Rewiring the lens cable in the lens iris plug Prepare the lens cable. Cut the cable at the plug, then remove approx. 8 mm of the cable sheath and strip about 2 mm from each wire. Install the lens iris plug. Solder the cable to the pins following the correct pin layout (refer to the table and illustrations), then close the plug cover.
CONNECTIONS Basic connection for monitoring or recording The peripheral devices (VCR, monitor, lens, etc.) and cables are sold separately. Make the video signal connection between the camera and the monitor or time lapse VCR. Connect DC connecting cord from the AC adaptor to the 12 V DC IN terminal on the camera. WARNING: •...
SETTINGS Camera setup section Electronic iris function setting Use a manual or fixed iris lens and set the lens aperture to the shortest F stop. Set the EI/AI switch to EI position. When using an auto-iris lens (for indoor/outdoor use) Set the EI/AI switch to the AI position.
SETTINGS Lens iris adjustment Backlight compensation setting If using a DC type auto-iris lens, you will need to set the LEVEL Use an auto-iris lens and set the BLC switch to volume when shooting in the conditions described below. the ON position, to engage the backlight compensation function.
Page 12
SETTINGS High speed electronic shutter setting Normally, the speed setting switch for the high speed electronic shutter set to the 0 position. This sets the electronic shutter speed to 1/50 sec. The switch can be set as indicated in table A to select one of the 8 speeds available.
Before taking the camera for repairs, please check below to make sure that the camera is used correctly. If it still does not perform correctly, please consult your dealer or a Sanyo Authorized Service Centre. No picture on the monitor screen •...
Servicing should always be referred to your dealer or Electronic iris range : 0.07 lux to 42,000 (F 1.4, lens) Sanyo Authorized Service Centre. 0.05 lux to 30,000 (F 1.2, lens) : 12.5 mm ± 0.8 mm Flange-back : γ...
ACCESSORIES SPECIFICATIONS Dimensions Lens iris plug (4-pin)..............1 pc. AC adaptor ................1 pc. Hexagonal wrench..............1 pc. SHUTTER VIDEO OUT POWER DC12V 1/4”–20 UNC 81.4 48.9 1,830 1,830 58.5 Features and specifications are subject to change without prior notice or obligations. English...