Table of Contents
Advertisement
To check whether TIME 1 or TIME 2 is currently displayed
In the Timekeeping Mode, push the crown in four times.
TIME 1
TIME 2
This will re-enter the Timekeeping Mode (page E-21).
The b Lower Dial Hand will indicate either TIME 1 (1-TIME) or TIME
2 (TIME-2) for about one second. After that, the b Lower Dial Hand
will move to the current day of the week.
When you return to the Timekeeping Mode from another mode
(by pushing in and holding the crown for about two seconds), the
b Lower Dial Hand will move directly to the day of the week without
fi rst indicating TIME 1 or TIME 2.
E-24
Confi guring Home City Settings
There are two Home City settings: actually selecting the Home City and selecting either standard time or
daylight saving time (DST).
To confi gure Home City settings
Note
This watch does not have a city code that corresponds to Newfoundland.
1.
Push in and hold the crown for at least two seconds.
This will enter the Timekeeping Mode (page E-21).
2.
Pull out the crown.
This will cause the x Second Hand to move to the city code of the
currently selected TIME (page E-22).
This indicates the city code setting mode.
TOKYO (TYO)
If you do not perform any operation with the crown for about three
minutes after pulling it out, crown operations will become disabled and
the hand will not move if you rotate the crown. If this happens, push the
crown back in and then pull it out again.
For details about city codes, see the "City Code Table" at the back of
this manual.
3.
Rotate the crown to move the
to assign to the currently selected TIME.
Each time you select a city code, the z Hour Hand, c Minute Hand,
b Lower Dial Hand and n Day move to the current time and date for
that city code.
E-26
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from Standard Time.
Remember that not all countries or even local areas use Daylight Saving Time.
The time calibration signals transmitted from Mainfl ingen (Germany), Anthorn (England), or Fort Collins
(the United States) include both Standard Time and DST data.
Note that an AUTO setting (Auto STD or Auto DST) will be indicated only if the currently selected city
code is one that supports calibration time signal reception. While AUTO is selected, the watch will
switch between STD and DST automatically in accordance with time calibration signal data.
The initial default setting is AUTO when any one of the following city codes is selected as the Home
City code: LONDON (LON), PARIS (PAR), ATHENS (ATH), NEW YORK (NYC), CHICAGO (CHI),
DENVER (DEN), LOS ANGELES (LAX), ANCHORAGE (ANC), or TOKYO (TYO).
For information about manually overriding the time calibration STD/DST setting, see "To manually
override a time calibration standard time/daylight saving time setting" (page E-30).
Note that you cannot switch between STD (standard time) and DST (daylight saving time) while UTC*
is selected as your Home City.
*
Coordinated Universal Time, the world-wide scientifi c standard of timekeeping. The reference point for
UTC is Greenwich, England.
If you experience problems receiving the time calibration signal in your area, it probably is best to
switch between Standard Time and Daylight Saving Time (summer time) manually (page E-30).
E-28
Note
Selecting some city codes makes it possible for the watch to receive the time calibration signal for the
corresponding area automatically. See page E-11 for details.
To manually override a time calibration standard time/daylight saving time setting
1.
Perform steps 1 and 2 under "To confi gure Home City settings" on page E-26.
Each time you select a city code, the z Hour Hand, c Minute Hand, and
STD by manual setting
v Upper Dial Hand move to the current time for that city code.
A for about three seconds until the short end of the b Lower Dial
2.
Hold down
Hand points to DST.
This is the STD/DST manual/auto switching mode.
Performing the above step selects manual DST switching.
Note that you cannot switch between manual and auto switching while the
currently selected city code of the Home City is one that does not support
DST by manual setting
time calibration signal reception.
A toggles between STD and DST as shown in the illustration
3.
Each press of
to the left.
4.
Push the crown back in to return to the Timekeeping Mode.
E-30
Operation Guide 5141 (OC)
x Second Hand to the city code you want
To switch from TIME 1 to TIME 2
1.
In the Timekeeping Mode, hold down
step 2 of this procedure is complete (about three seconds). During that
period, the watch will perform the following operations automatically.
The x Second Hand will move to the city code of the currently
selected TIME (TIME 1 or TIME 2).
Next, the x Second Hand will move to the city code of the other TIME.
After that, the time and date settings will change to those for the
newly selected TIME.
Finally, the b Lower Dial Hand will indicate the new TIME (TIME 1 or
TIME 2) selection.
TOKYO (TYO)
2.
You can release
Hand.
City code
After about one second, the b Lower Dial Hand will indicate the
current day of the week for the selected TIME.
Pressing A during the one second after switching will indicate the
day of the week immediately.
To return to TIME 1 from TIME 2, hold down A in the Timekeeping
Mode again.
A to toggle the time for the currently selected city code between STD
4.
Press
STD setting by time
(standard time) and DST (daylight saving time).
calibration signal
In the city code setting mode, the short end of the b Lower Dial Hand
indicates the current daylight saving time setting as STD (standard time) or
DST (daylight saving time).
Note that an AUTO setting (Auto STD or Auto DST) will be indicated only if
the currently selected city code is one that supports calibration time signal
reception. While AUTO is selected, the watch will switch between STD and
DST automatically in accordance with time calibration signal data.
DST setting by time
While AUTO is in use, the short end of the b Lower Dial Hand will point to
calibration signal
the STD side or the DST side of AUTO, depending on the current STD/DST
setting.
The initial default setting is AUTO when any one of the following city
codes is selected as the Home City code: LONDON (LON), PARIS (PAR),
ATHENS (ATH), NEW YORK (NYC), CHICAGO (CHI), DENVER (DEN), LOS
ANGELES (LAX), ANCHORAGE (ANC), or TOKYO (TYO).
For details about the Daylight Saving Time setting, see "Daylight Saving
Time (DST)" (page E-28).
5.
After the settings are the way you want, push the crown back in to return to
the Timekeeping Mode.
STD/DST Switching
STD/DST switching can be performed either automatically or manually, depending on time calibration
signal reception conditions in your area, the use of daylight saving time in your area, etc.
−
To confi gure the watch to switch between STD and DST automatically in accordance with a time
calibration signal, see "To toggle the Home City time between standard time and daylight saving
time" (page E-29)
−
To override time calibration data and use a fi xed STD/DST setting, see "To manually override a time
calibration standard time/daylight saving time setting" (page E-30).
To toggle the Home City time between standard time and daylight saving time
1.
Perform steps 1 and 2 under "To confi gure Home City settings" on page E-26.
Each time you select a city code, the z Hour Hand, c Minute Hand, and
STD setting by time
v Upper Dial Hand move to the current time for that city code.
calibration signal
A to toggle the time for the currently selected city code between STD
2.
Press
(standard time) and DST (daylight saving time).
The short end of the b Lower Dial Hand will indicate the current daylight
saving time setting as STD (standard time) or DST (daylight saving time).
When AUTO is enabled, the short end of the b Lower Dial Hand will point
to the STD side of AUTO or the DST side (depending on the current STD/
DST setting by time
DST setting) of AUTO.
calibration signal
3.
After the settings are the way you want, push the crown back in to return to
the Timekeeping Mode.
Confi guring Current Time and Date Settings Manually
You can confi gure current time and date settings manually when the watch is unable to receive a time
calibration signal.
To change the current time setting manually
1.
In the Timekeeping Mode, pull out the crown.
This will cause the x Second Hand to move to the city code of the
currently selected TIME (page E-22).
At this time, the short end of the b Lower Dial Hand will indicate the
Home City's current daylight saving time setting (STD or DST).
If you do not perform any operation with the crown for about three minutes
after pulling it out, crown operations will become disabled and the hand
will not move if you rotate the crown. If this happens, push the crown back
in and then pull it out again.
TOKYO (TYO)
A and keep it held down until
A after the TIME is indicated by the b Lower Dial
E-25
E-27
E-29
E-31
Hide quick links:
Advertisement
Table of Contents
