Table of Contents
Advertisement
OPERATION
SECURfTY
CODE
WALL MOUNTING
(if dasirad)
The CLA-I 380AUS has a digfial security system with 10 milhon pessible
codas. Th!s system helps prevant the unauthorized use of your telephone
To mount the basa station on a wail
Ihneby another cordleaa tefephans war.
1. Inaaf the heals of the hangar in the holes in the back of the base sfahon.
A aecunfy code ia sat aufomafiilly
the first time the hamleet ia placed in tha
Then push tham in the diracfion of arrow @as
shown.
basa station cradla When the coda is sat, a bep
sounds.
Tha eecunfy cccte must b reset if the battery pack is raplaced or the powar is
2. Connact tha cord.
interwptad.
How to reset your security coda
1. Place the handset m the cradle
of the base station.
2. Press the PAGEilNT button on
the base station (wtihin 3
aaconds). A baap sounds wlthm
30 saconds. Tha sacunfy code
is now sat.
To change your sacunfy ccxfe
at any time, simply repaat the
above steps. A new sacurify
code IS automal!aliy
set each
time.
NOTES
-
It is nacas-sary to change the
Wcurify Cede it
. There is a pewar failure.
The baffary pack is changad.
oTha battery pack is exhaust-
ed.
. The AC adap+or is dkconnacf-
ed.
-
If fha sacurify coda has bean
claarad, talk cannot ba made
until the coda IS met.
NT
u
button
ANSWERING
SYSTEM
RING DELAY SWfTCH
(2/4/AUTO)
The RING DELAY switch lets you
choose the numbar of times the
telaphone rings before a call IS
answerad
2 position
Incommg calls are answerad on
the sacond ring.
-
4 pilstion:
Incommg calls are answarad on
the fourth ring.
AUTO (Toll Savar) position
The first incoming call is
answerad on the fowfh rfng,
and later calls are anawerad on
the sacond ring. If you call your
numbar from anothar phona
and hear threa rings, you know
you have no messages and can
hang up and save the cost of
the call. When you reset the
unit to the auto answar mode,
the unit again answera the fitat
new call on tha fourth ring.
RING DELAY switch
CPC OWOFF
The telephone systems in many
areas provide a disconnect puke
when a caller hangs up. If the
CPCIANS.ONLY
switch (Imatad
on the side of the basa station) is
sat to CPC ON, tha CIA-13S0
stops racording and returns to the
auto anawer mode when this
dkconnecf puke ia raceivad This
eliminates annoying recodings of
dial tonaa between meaaages.
The CPC/ANS.ONLY
switch
should ba kept in the CPC OFF
position it
-
Your telephone is aquIppad
with call waiting sarvke
-
You have a noisy telephone
exchange
(If the switch is not in the CPC
OFF position, your calls may ba
disconnected prematurely.)
ANSWER
ONLY
If you do not want massagas to ba
raceivad and racordad, sat the
switch to the ANS.ONLY
peaiion.
The unil then plays your outgoing
massage but doss not record
iktcoming messages.
CPWANS.ONLY
switch
3. Mount tha basa station on the wall
P
. . .
?,,"'
>
-l!
/;
~
o
[>*k,,
,,
A
Wall-mount
.)2
hanger
To socket
+
wall
NOTES:
Ths cordless tefaphone may not be compafibfa with carfain mUlfip18 lit18
PBX systama.
Avoid Imatwns near ekfrical
aquipment such aa computers, Ns,
flwraacant
lamps, halogen Iampa or microwave ovans. Thesa may
causa mterferenca or reduca the operating range of the cordless tela-
phone.
RECORDING
AN OUTGOING
MESSAGE
Safore you racord your outgoing message, dwde
what you are going to say
and write il down.
SAMPLE
OUTGOING
MESSAGE
"Hello. Th#s IS (your nama). Please leave your nama and teL@wne
number
and a brief messaga, and your ca// wi// be retumad as .xxM aa Po.saible.
Thank you. "
NOTES:
The message tape must b-s
insertad before an outgoing
message can be racordad. This
enauraa that them is a backup
tape racordhg of your outgoing
meaaage in the event of a powar
failure. (Sea "POWER FAILURE",
page 40.)
-
If you anempt to record an
outgoing message without a
message tapa insertad, 3 long
bsaps sound.
-
Your outgoing message can ba
up to approximately 16 saconds
in length. The IN USE ind~tor
flashes to alert you during the last
4 saconds of racording fima.
If you anempt to racord an
outgoing message more than 16
saconds In length, the answaring
system automaocalty stops
racording and enters the auto
answer mode
When outgoing messaga recorr-
lng la complatad, the unit swtch-
es to the auto answer mode
automatwally. If you want to
cancal the auto answer mode,
press fhe STOP button.
If an mcommg call is recaivad
while you are rawrdng
your
outgoing messaga or while the
backup tapa racordmg IS being
made, your outgoing massage IS
erasad. If thts happans, racord
your outgoing mesaaga again.
-
When you replace the message
tapa, you must racord your
oofgoing message again.
1. Press the STO~ bu~on.
–
2. Sal Ihe VOLUME control to the
mid position.
3. Press and hold the OGM REC
button for approximately t
sacond until a beep sounds.
The IN USE indicator fights.
4. When you haar the baap tone,
rscord your messaga using the
bunk-in mwophore.
5. Press the OGM REC button
again to end recording.
The IN USE and ANSWER
indicator flash affemately, and
your outgoing meseage plays
back automafiially.
(A backup
racmding of your outgoing
message is made automatically
on the message tape.)
~icrophone(MIC)
–4-
Advertisement
Table of Contents
Troubleshooting
