Assembly - Hilti WSJ 750-ET Operating Instructions Manual

Technical data
Tool
Nominal power rating
Nominal voltage
Mains frequency
Nominal current input
Weight of tool
Dimensions
(LxWxH)
Stroke rate
Stroke lenght
Max. cutting depth in wood
Max. cutting depth in aluminium
Max. cutting depth in mild steel
Angular cutting (left / right)
Number of orbital action settings
Blade connection end
Dust removal adapter exterior dia. 30 mm (1
Protection class II (double insulated) Z
Supplemental vibration-absorbing grip (a check showing it is only on the WSR 850 models)
Counter balance for low vibration, applicable to all models
Right of technical changes reserved!

5. Assembly

The cutting edges of the saw blade
G
are sharp.
The cutting edges may present a risk
G
of injury.
Wear protective gloves.
G
5.1 Extension cords
If extension cords are used: Use only extension cords
of a type approved for the intended purpose and of ade-
quate cross section. Failure to observe this point may
result in reduced performance and may cause the cord
to overheat. Replace damaged extension cords. Use only
correspondingly marked and approved extension cords
for working outdoors. Recommended minimum cross
sections and max. cord lengths:
Mains Conductor cross section
voltage 1.5 mm 2 2.5 mm
110–120 V 20 m 40 m
230 V 50 m 100 m
Printed: 07.07.2013 | Doc-Nr: PUB / 5071337 / 000 / 00
WSJ 750-ET
750 W
120 V
50 / 60 Hz
7.8 A
2.6 kg (5.7 lb)
256x75x201 mm
(10x3x8 in)
900–3000/min.
28 mm (1 1 ⁄ ")
8
up to 120 mm
(4 11 ⁄ ")
16
up to 25 mm
(1")
up to 10 mm
( ⁄ ")
3
8
0–45°
0-1-2-3
T-shank
1 / ") for hose adapter
4
-CAUTION-
AWG
2 14 12
75 ft 125 ft
– –
WSJ 750-EB WSJ 850-ET
750 W 850 W
120 V 120 V
50 / 60 Hz 50 / 60 Hz
7.8 A 8.4 A
2.5 kg (5.5 lb) 2.6 kg (5.7 lb)
256x75x194 mm 256x75x201 mm
(10x3x7.6 in) (10x3x8 in)
900–3000/min. 900–3000/min.
28 mm (1 1 ⁄ ") 28 mm (1
8
up to 120 mm up to 150 mm
(4 11 ⁄ ") (5 7 ⁄ ")
16 8
up to 25 mm up to 25 mm
(1") (1")
up to 10 mm up to 10 mm
( ⁄ ") ( ⁄ ")
3 3
8 8
0–45° 0–45°
0-1-2-3 0-1-2-3
T-shank T-shank
Extension cords for outdoor use
For outdoor work use only extension cords approved and
correspondingly marked as suitable for outdoor use.
5.2 Fitting the saw blade
1. Unplug the supply cord from the electric socket.
2. Press the saw blade release lever and hold it in this
position.
3. Push the saw blade into the blade holder (teeth fac-
ing cutting direction) until it engages.
4. Hold the blade against the resistance felt and then
allow the blade release lever to return to its original
position.
5. Check that the blade is held securely by gripping and
pulling it.
5.3 Changing the saw blade
-CAUTION-
When changing the saw blade, hold the tool in such a
way that persons or animals cannot be injured by the
saw blade as it is ejected.
1. Unplug the supply cord from the electric socket.
2. Press the saw blade release lever to the side as far as
it will go. The saw blade is then released and ejected.
WSJ 850-EB
850 W
120 V
50 / 60 Hz
8.4 A
2.5 kg (5.5 lb)
256x75x194 mm
(10x3x7.6 in)
900–3000/min.
1 ⁄ ") 28 mm (1 1 ⁄ ")
8 8
up to 150 mm
(5 7 ⁄ ")
8
up to 25 mm
(1")
up to 10 mm
( ⁄ ")
3
8
0–45°
0-1-2-3
T-shank
en
5